Viewing file:  nl80211.h (327.41 KB) -rw-r--r--
Select action/file-type:
 (+) |  (+) |  (+) | Code (+) | Session (+) |  (+) | SDB (+) |  (+) |  (+) |  (+) |  (+) |  (+) |
#ifndef __LINUX_NL80211_H
#define __LINUX_NL80211_H
/*
* 802.11 netlink interface public header
*
* Copyright 2006-2010 Johannes Berg <johannes@sipsolutions.net>
* Copyright 2008 Michael Wu <flamingice@sourmilk.net>
* Copyright 2008 Luis Carlos Cobo <luisca@cozybit.com>
* Copyright 2008 Michael Buesch <m@bues.ch>
* Copyright 2008, 2009 Luis R. Rodriguez <lrodriguez@atheros.com>
* Copyright 2008 Jouni Malinen <jouni.malinen@atheros.com>
* Copyright 2008 Colin McCabe <colin@cozybit.com>
* Copyright 2015-2017 Intel Deutschland GmbH
* Copyright (C) 2018-2022 Intel Corporation
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
* copyright notice and this permission notice appear in all copies.
*
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*
*/
/*
* This header file defines the userspace API to the wireless stack. Please
* be careful not to break things - i.e. don't move anything around or so
* unless you can demonstrate that it breaks neither API nor ABI.
*
* Additions to the API should be accompanied by actual implementations in
* an upstream driver, so that example implementations exist in case there
* are ever concerns about the precise semantics of the API or changes are
* needed, and to ensure that code for dead (no longer implemented) API
* can actually be identified and removed.
* Nonetheless, semantics should also be documented carefully in this file.
*/
#include <linux/types.h>
#define NL80211_GENL_NAME "nl80211"
#define NL80211_MULTICAST_GROUP_CONFIG "config"
#define NL80211_MULTICAST_GROUP_SCAN "scan"
#define NL80211_MULTICAST_GROUP_REG "regulatory"
#define NL80211_MULTICAST_GROUP_MLME "mlme"
#define NL80211_MULTICAST_GROUP_VENDOR "vendor"
#define NL80211_MULTICAST_GROUP_NAN "nan"
#define NL80211_MULTICAST_GROUP_TESTMODE "testmode"
#define NL80211_EDMG_BW_CONFIG_MIN 4
#define NL80211_EDMG_BW_CONFIG_MAX 15
#define NL80211_EDMG_CHANNELS_MIN 1
#define NL80211_EDMG_CHANNELS_MAX 0x3c /* 0b00111100 */
/**
* DOC: Station handling
*
* Stations are added per interface, but a special case exists with VLAN
* interfaces. When a station is bound to an AP interface, it may be moved
* into a VLAN identified by a VLAN interface index (%NL80211_ATTR_STA_VLAN).
* The station is still assumed to belong to the AP interface it was added
* to.
*
* Station handling varies per interface type and depending on the driver's
* capabilities.
*
* For drivers supporting TDLS with external setup (WIPHY_FLAG_SUPPORTS_TDLS
* and WIPHY_FLAG_TDLS_EXTERNAL_SETUP), the station lifetime is as follows:
* - a setup station entry is added, not yet authorized, without any rate
* or capability information, this just exists to avoid race conditions
* - when the TDLS setup is done, a single NL80211_CMD_SET_STATION is valid
* to add rate and capability information to the station and at the same
* time mark it authorized.
* - %NL80211_TDLS_ENABLE_LINK is then used
* - after this, the only valid operation is to remove it by tearing down
* the TDLS link (%NL80211_TDLS_DISABLE_LINK)
*
* TODO: need more info for other interface types
*/
/**
* DOC: Frame transmission/registration support
*
* Frame transmission and registration support exists to allow userspace
* management entities such as wpa_supplicant react to management frames
* that are not being handled by the kernel. This includes, for example,
* certain classes of action frames that cannot be handled in the kernel
* for various reasons.
*
* Frame registration is done on a per-interface basis and registrations
* cannot be removed other than by closing the socket. It is possible to
* specify a registration filter to register, for example, only for a
* certain type of action frame. In particular with action frames, those
* that userspace registers for will not be returned as unhandled by the
* driver, so that the registered application has to take responsibility
* for doing that.
*
* The type of frame that can be registered for is also dependent on the
* driver and interface type. The frame types are advertised in wiphy
* attributes so applications know what to expect.
*
* NOTE: When an interface changes type while registrations are active,
* these registrations are ignored until the interface type is
* changed again. This means that changing the interface type can
* lead to a situation that couldn't otherwise be produced, but
* any such registrations will be dormant in the sense that they
* will not be serviced, i.e. they will not receive any frames.
*
* Frame transmission allows userspace to send for example the required
* responses to action frames. It is subject to some sanity checking,
* but many frames can be transmitted. When a frame was transmitted, its
* status is indicated to the sending socket.
*
* For more technical details, see the corresponding command descriptions
* below.
*/
/**
* DOC: Virtual interface / concurrency capabilities
*
* Some devices are able to operate with virtual MACs, they can have
* more than one virtual interface. The capability handling for this
* is a bit complex though, as there may be a number of restrictions
* on the types of concurrency that are supported.
*
* To start with, each device supports the interface types listed in
* the %NL80211_ATTR_SUPPORTED_IFTYPES attribute, but by listing the
* types there no concurrency is implied.
*
* Once concurrency is desired, more attributes must be observed:
* To start with, since some interface types are purely managed in
* software, like the AP-VLAN type in mac80211 for example, there's
* an additional list of these, they can be added at any time and
* are only restricted by some semantic restrictions (e.g. AP-VLAN
* cannot be added without a corresponding AP interface). This list
* is exported in the %NL80211_ATTR_SOFTWARE_IFTYPES attribute.
*
* Further, the list of supported combinations is exported. This is
* in the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute. Basically,
* it exports a list of "groups", and at any point in time the
* interfaces that are currently active must fall into any one of
* the advertised groups. Within each group, there are restrictions
* on the number of interfaces of different types that are supported
* and also the number of different channels, along with potentially
* some other restrictions. See &enum nl80211_if_combination_attrs.
*
* All together, these attributes define the concurrency of virtual
* interfaces that a given device supports.
*/
/**
* DOC: packet coalesce support
*
* In most cases, host that receives IPv4 and IPv6 multicast/broadcast
* packets does not do anything with these packets. Therefore the
* reception of these unwanted packets causes unnecessary processing
* and power consumption.
*
* Packet coalesce feature helps to reduce number of received interrupts
* to host by buffering these packets in firmware/hardware for some
* predefined time. Received interrupt will be generated when one of the
* following events occur.
* a) Expiration of hardware timer whose expiration time is set to maximum
* coalescing delay of matching coalesce rule.
* b) Coalescing buffer in hardware reaches it's limit.
* c) Packet doesn't match any of the configured coalesce rules.
*
* User needs to configure following parameters for creating a coalesce
* rule.
* a) Maximum coalescing delay
* b) List of packet patterns which needs to be matched
* c) Condition for coalescence. pattern 'match' or 'no match'
* Multiple such rules can be created.
*/
/**
* DOC: WPA/WPA2 EAPOL handshake offload
*
* By setting @NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_PSK flag drivers
* can indicate they support offloading EAPOL handshakes for WPA/WPA2
* preshared key authentication in station mode. In %NL80211_CMD_CONNECT
* the preshared key should be specified using %NL80211_ATTR_PMK. Drivers
* supporting this offload may reject the %NL80211_CMD_CONNECT when no
* preshared key material is provided, for example when that driver does
* not support setting the temporal keys through %NL80211_CMD_NEW_KEY.
*
* Similarly @NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_1X flag can be
* set by drivers indicating offload support of the PTK/GTK EAPOL
* handshakes during 802.1X authentication in station mode. In order to
* use the offload the %NL80211_CMD_CONNECT should have
* %NL80211_ATTR_WANT_1X_4WAY_HS attribute flag. Drivers supporting this
* offload may reject the %NL80211_CMD_CONNECT when the attribute flag is
* not present.
*
* By setting @NL80211_EXT_FEATURE_4WAY_HANDSHAKE_AP_PSK flag drivers
* can indicate they support offloading EAPOL handshakes for WPA/WPA2
* preshared key authentication in AP mode. In %NL80211_CMD_START_AP
* the preshared key should be specified using %NL80211_ATTR_PMK. Drivers
* supporting this offload may reject the %NL80211_CMD_START_AP when no
* preshared key material is provided, for example when that driver does
* not support setting the temporal keys through %NL80211_CMD_NEW_KEY.
*
* For 802.1X the PMK or PMK-R0 are set by providing %NL80211_ATTR_PMK
* using %NL80211_CMD_SET_PMK. For offloaded FT support also
* %NL80211_ATTR_PMKR0_NAME must be provided.
*/
/**
* DOC: FILS shared key authentication offload
*
* FILS shared key authentication offload can be advertized by drivers by
* setting @NL80211_EXT_FEATURE_FILS_SK_OFFLOAD flag. The drivers that support
* FILS shared key authentication offload should be able to construct the
* authentication and association frames for FILS shared key authentication and
* eventually do a key derivation as per IEEE 802.11ai. The below additional
* parameters should be given to driver in %NL80211_CMD_CONNECT and/or in
* %NL80211_CMD_UPDATE_CONNECT_PARAMS.
* %NL80211_ATTR_FILS_ERP_USERNAME - used to construct keyname_nai
* %NL80211_ATTR_FILS_ERP_REALM - used to construct keyname_nai
* %NL80211_ATTR_FILS_ERP_NEXT_SEQ_NUM - used to construct erp message
* %NL80211_ATTR_FILS_ERP_RRK - used to generate the rIK and rMSK
* rIK should be used to generate an authentication tag on the ERP message and
* rMSK should be used to derive a PMKSA.
* rIK, rMSK should be generated and keyname_nai, sequence number should be used
* as specified in IETF RFC 6696.
*
* When FILS shared key authentication is completed, driver needs to provide the
* below additional parameters to userspace, which can be either after setting
* up a connection or after roaming.
* %NL80211_ATTR_FILS_KEK - used for key renewal
* %NL80211_ATTR_FILS_ERP_NEXT_SEQ_NUM - used in further EAP-RP exchanges
* %NL80211_ATTR_PMKID - used to identify the PMKSA used/generated
* %Nl80211_ATTR_PMK - used to update PMKSA cache in userspace
* The PMKSA can be maintained in userspace persistently so that it can be used
* later after reboots or wifi turn off/on also.
*
* %NL80211_ATTR_FILS_CACHE_ID is the cache identifier advertized by a FILS
* capable AP supporting PMK caching. It specifies the scope within which the
* PMKSAs are cached in an ESS. %NL80211_CMD_SET_PMKSA and
* %NL80211_CMD_DEL_PMKSA are enhanced to allow support for PMKSA caching based
* on FILS cache identifier. Additionally %NL80211_ATTR_PMK is used with
* %NL80211_SET_PMKSA to specify the PMK corresponding to a PMKSA for driver to
* use in a FILS shared key connection with PMKSA caching.
*/
/**
* DOC: SAE authentication offload
*
* By setting @NL80211_EXT_FEATURE_SAE_OFFLOAD flag drivers can indicate they
* support offloading SAE authentication for WPA3-Personal networks in station
* mode. Similarly @NL80211_EXT_FEATURE_SAE_OFFLOAD_AP flag can be set by
* drivers indicating the offload support in AP mode.
*
* The password for SAE should be specified using %NL80211_ATTR_SAE_PASSWORD in
* %NL80211_CMD_CONNECT and %NL80211_CMD_START_AP for station and AP mode
* respectively.
*/
/**
* DOC: VLAN offload support for setting group keys and binding STAs to VLANs
*
* By setting @NL80211_EXT_FEATURE_VLAN_OFFLOAD flag drivers can indicate they
* support offloading VLAN functionality in a manner where the driver exposes a
* single netdev that uses VLAN tagged frames and separate VLAN-specific netdevs
* can then be added using RTM_NEWLINK/IFLA_VLAN_ID similarly to the Ethernet
* case. Frames received from stations that are not assigned to any VLAN are
* delivered on the main netdev and frames to such stations can be sent through
* that main netdev.
*
* %NL80211_CMD_NEW_KEY (for group keys), %NL80211_CMD_NEW_STATION, and
* %NL80211_CMD_SET_STATION will optionally specify vlan_id using
* %NL80211_ATTR_VLAN_ID.
*/
/**
* DOC: TID configuration
*
* TID config support can be checked in the %NL80211_ATTR_TID_CONFIG
* attribute given in wiphy capabilities.
*
* The necessary configuration parameters are mentioned in
* &enum nl80211_tid_config_attr and it will be passed to the
* %NL80211_CMD_SET_TID_CONFIG command in %NL80211_ATTR_TID_CONFIG.
*
* If the configuration needs to be applied for specific peer then the MAC
* address of the peer needs to be passed in %NL80211_ATTR_MAC, otherwise the
* configuration will be applied for all the connected peers in the vif except
* any peers that have peer specific configuration for the TID by default; if
* the %NL80211_TID_CONFIG_ATTR_OVERRIDE flag is set, peer specific values
* will be overwritten.
*
* All this configuration is valid only for STA's current connection
* i.e. the configuration will be reset to default when the STA connects back
* after disconnection/roaming, and this configuration will be cleared when
* the interface goes down.
*/
/**
* DOC: FILS shared key crypto offload
*
* This feature is applicable to drivers running in AP mode.
*
* FILS shared key crypto offload can be advertised by drivers by setting
* @NL80211_EXT_FEATURE_FILS_CRYPTO_OFFLOAD flag. The drivers that support
* FILS shared key crypto offload should be able to encrypt and decrypt
* association frames for FILS shared key authentication as per IEEE 802.11ai.
* With this capability, for FILS key derivation, drivers depend on userspace.
*
* After FILS key derivation, userspace shares the FILS AAD details with the
* driver and the driver stores the same to use in decryption of association
* request and in encryption of association response. The below parameters
* should be given to the driver in %NL80211_CMD_SET_FILS_AAD.
* %NL80211_ATTR_MAC - STA MAC address, used for storing FILS AAD per STA
* %NL80211_ATTR_FILS_KEK - Used for encryption or decryption
* %NL80211_ATTR_FILS_NONCES - Used for encryption or decryption
* (STA Nonce 16 bytes followed by AP Nonce 16 bytes)
*
* Once the association is done, the driver cleans the FILS AAD data.
*/
/**
* DOC: Multi-Link Operation
*
* In Multi-Link Operation, a connection between to MLDs utilizes multiple
* links. To use this in nl80211, various commands and responses now need
* to or will include the new %NL80211_ATTR_MLO_LINKS attribute.
* Additionally, various commands that need to operate on a specific link
* now need to be given the %NL80211_ATTR_MLO_LINK_ID attribute, e.g. to
* use %NL80211_CMD_START_AP or similar functions.
*/
/**
* enum nl80211_commands - supported nl80211 commands
*
* @NL80211_CMD_UNSPEC: unspecified command to catch errors
*
* @NL80211_CMD_GET_WIPHY: request information about a wiphy or dump request
* to get a list of all present wiphys.
* @NL80211_CMD_SET_WIPHY: set wiphy parameters, needs %NL80211_ATTR_WIPHY or
* %NL80211_ATTR_IFINDEX; can be used to set %NL80211_ATTR_WIPHY_NAME,
* %NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ,
* %NL80211_ATTR_WIPHY_FREQ_OFFSET (and the attributes determining the
* channel width; this is used for setting monitor mode channel),
* %NL80211_ATTR_WIPHY_RETRY_SHORT, %NL80211_ATTR_WIPHY_RETRY_LONG,
* %NL80211_ATTR_WIPHY_FRAG_THRESHOLD, and/or
* %NL80211_ATTR_WIPHY_RTS_THRESHOLD. However, for setting the channel,
* see %NL80211_CMD_SET_CHANNEL instead, the support here is for backward
* compatibility only.
* @NL80211_CMD_NEW_WIPHY: Newly created wiphy, response to get request
* or rename notification. Has attributes %NL80211_ATTR_WIPHY and
* %NL80211_ATTR_WIPHY_NAME.
* @NL80211_CMD_DEL_WIPHY: Wiphy deleted. Has attributes
* %NL80211_ATTR_WIPHY and %NL80211_ATTR_WIPHY_NAME.
*
* @NL80211_CMD_GET_INTERFACE: Request an interface's configuration;
* either a dump request for all interfaces or a specific get with a
* single %NL80211_ATTR_IFINDEX is supported.
* @NL80211_CMD_SET_INTERFACE: Set type of a virtual interface, requires
* %NL80211_ATTR_IFINDEX and %NL80211_ATTR_IFTYPE.
* @NL80211_CMD_NEW_INTERFACE: Newly created virtual interface or response
* to %NL80211_CMD_GET_INTERFACE. Has %NL80211_ATTR_IFINDEX,
* %NL80211_ATTR_WIPHY and %NL80211_ATTR_IFTYPE attributes. Can also
* be sent from userspace to request creation of a new virtual interface,
* then requires attributes %NL80211_ATTR_WIPHY, %NL80211_ATTR_IFTYPE and
* %NL80211_ATTR_IFNAME.
* @NL80211_CMD_DEL_INTERFACE: Virtual interface was deleted, has attributes
* %NL80211_ATTR_IFINDEX and %NL80211_ATTR_WIPHY. Can also be sent from
* userspace to request deletion of a virtual interface, then requires
* attribute %NL80211_ATTR_IFINDEX. If multiple BSSID advertisements are
* enabled using %NL80211_ATTR_MBSSID_CONFIG, %NL80211_ATTR_MBSSID_ELEMS,
* and if this command is used for the transmitting interface, then all
* the non-transmitting interfaces are deleted as well.
*
* @NL80211_CMD_GET_KEY: Get sequence counter information for a key specified
* by %NL80211_ATTR_KEY_IDX and/or %NL80211_ATTR_MAC. %NL80211_ATTR_MAC
* represents peer's MLD address for MLO pairwise key. For MLO group key,
* the link is identified by %NL80211_ATTR_MLO_LINK_ID.
* @NL80211_CMD_SET_KEY: Set key attributes %NL80211_ATTR_KEY_DEFAULT,
* %NL80211_ATTR_KEY_DEFAULT_MGMT, or %NL80211_ATTR_KEY_THRESHOLD.
* For MLO connection, the link to set default key is identified by
* %NL80211_ATTR_MLO_LINK_ID.
* @NL80211_CMD_NEW_KEY: add a key with given %NL80211_ATTR_KEY_DATA,
* %NL80211_ATTR_KEY_IDX, %NL80211_ATTR_MAC, %NL80211_ATTR_KEY_CIPHER,
* and %NL80211_ATTR_KEY_SEQ attributes. %NL80211_ATTR_MAC represents
* peer's MLD address for MLO pairwise key. The link to add MLO
* group key is identified by %NL80211_ATTR_MLO_LINK_ID.
* @NL80211_CMD_DEL_KEY: delete a key identified by %NL80211_ATTR_KEY_IDX
* or %NL80211_ATTR_MAC. %NL80211_ATTR_MAC represents peer's MLD address
* for MLO pairwise key. The link to delete group key is identified by
* %NL80211_ATTR_MLO_LINK_ID.
*
* @NL80211_CMD_GET_BEACON: (not used)
* @NL80211_CMD_SET_BEACON: change the beacon on an access point interface
* using the %NL80211_ATTR_BEACON_HEAD and %NL80211_ATTR_BEACON_TAIL
* attributes. For drivers that generate the beacon and probe responses
* internally, the following attributes must be provided: %NL80211_ATTR_IE,
* %NL80211_ATTR_IE_PROBE_RESP and %NL80211_ATTR_IE_ASSOC_RESP.
* @NL80211_CMD_START_AP: Start AP operation on an AP interface, parameters
* are like for %NL80211_CMD_SET_BEACON, and additionally parameters that
* do not change are used, these include %NL80211_ATTR_BEACON_INTERVAL,
* %NL80211_ATTR_DTIM_PERIOD, %NL80211_ATTR_SSID,
* %NL80211_ATTR_HIDDEN_SSID, %NL80211_ATTR_CIPHERS_PAIRWISE,
* %NL80211_ATTR_CIPHER_GROUP, %NL80211_ATTR_WPA_VERSIONS,
* %NL80211_ATTR_AKM_SUITES, %NL80211_ATTR_PRIVACY,
* %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_INACTIVITY_TIMEOUT,
* %NL80211_ATTR_ACL_POLICY and %NL80211_ATTR_MAC_ADDRS.
* The channel to use can be set on the interface or be given using the
* %NL80211_ATTR_WIPHY_FREQ and %NL80211_ATTR_WIPHY_FREQ_OFFSET, and the
* attributes determining channel width.
* @NL80211_CMD_NEW_BEACON: old alias for %NL80211_CMD_START_AP
* @NL80211_CMD_STOP_AP: Stop AP operation on the given interface
* @NL80211_CMD_DEL_BEACON: old alias for %NL80211_CMD_STOP_AP
*
* @NL80211_CMD_GET_STATION: Get station attributes for station identified by
* %NL80211_ATTR_MAC on the interface identified by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_SET_STATION: Set station attributes for station identified by
* %NL80211_ATTR_MAC on the interface identified by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_NEW_STATION: Add a station with given attributes to the
* interface identified by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_DEL_STATION: Remove a station identified by %NL80211_ATTR_MAC
* or, if no MAC address given, all stations, on the interface identified
* by %NL80211_ATTR_IFINDEX. For MLD station, MLD address is used in
* %NL80211_ATTR_MAC. %NL80211_ATTR_MGMT_SUBTYPE and
* %NL80211_ATTR_REASON_CODE can optionally be used to specify which type
* of disconnection indication should be sent to the station
* (Deauthentication or Disassociation frame and reason code for that
* frame).
*
* @NL80211_CMD_GET_MPATH: Get mesh path attributes for mesh path to
* destination %NL80211_ATTR_MAC on the interface identified by
* %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_SET_MPATH: Set mesh path attributes for mesh path to
* destination %NL80211_ATTR_MAC on the interface identified by
* %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_NEW_MPATH: Create a new mesh path for the destination given by
* %NL80211_ATTR_MAC via %NL80211_ATTR_MPATH_NEXT_HOP.
* @NL80211_CMD_DEL_MPATH: Delete a mesh path to the destination given by
* %NL80211_ATTR_MAC.
* @NL80211_CMD_NEW_PATH: Add a mesh path with given attributes to the
* interface identified by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_DEL_PATH: Remove a mesh path identified by %NL80211_ATTR_MAC
* or, if no MAC address given, all mesh paths, on the interface identified
* by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_SET_BSS: Set BSS attributes for BSS identified by
* %NL80211_ATTR_IFINDEX.
*
* @NL80211_CMD_GET_REG: ask the wireless core to send us its currently set
* regulatory domain. If %NL80211_ATTR_WIPHY is specified and the device
* has a private regulatory domain, it will be returned. Otherwise, the
* global regdomain will be returned.
* A device will have a private regulatory domain if it uses the
* regulatory_hint() API. Even when a private regdomain is used the channel
* information will still be mended according to further hints from
* the regulatory core to help with compliance. A dump version of this API
* is now available which will returns the global regdomain as well as
* all private regdomains of present wiphys (for those that have it).
* If a wiphy is self-managed (%NL80211_ATTR_WIPHY_SELF_MANAGED_REG), then
* its private regdomain is the only valid one for it. The regulatory
* core is not used to help with compliance in this case.
* @NL80211_CMD_SET_REG: Set current regulatory domain. CRDA sends this command
* after being queried by the kernel. CRDA replies by sending a regulatory
* domain structure which consists of %NL80211_ATTR_REG_ALPHA set to our
* current alpha2 if it found a match. It also provides
* NL80211_ATTR_REG_RULE_FLAGS, and a set of regulatory rules. Each
* regulatory rule is a nested set of attributes given by
* %NL80211_ATTR_REG_RULE_FREQ_[START|END] and
* %NL80211_ATTR_FREQ_RANGE_MAX_BW with an attached power rule given by
* %NL80211_ATTR_REG_RULE_POWER_MAX_ANT_GAIN and
* %NL80211_ATTR_REG_RULE_POWER_MAX_EIRP.
* @NL80211_CMD_REQ_SET_REG: ask the wireless core to set the regulatory domain
* to the specified ISO/IEC 3166-1 alpha2 country code. The core will
* store this as a valid request and then query userspace for it.
*
* @NL80211_CMD_GET_MESH_CONFIG: Get mesh networking properties for the
* interface identified by %NL80211_ATTR_IFINDEX
*
* @NL80211_CMD_SET_MESH_CONFIG: Set mesh networking properties for the
* interface identified by %NL80211_ATTR_IFINDEX
*
* @NL80211_CMD_SET_MGMT_EXTRA_IE: Set extra IEs for management frames. The
* interface is identified with %NL80211_ATTR_IFINDEX and the management
* frame subtype with %NL80211_ATTR_MGMT_SUBTYPE. The extra IE data to be
* added to the end of the specified management frame is specified with
* %NL80211_ATTR_IE. If the command succeeds, the requested data will be
* added to all specified management frames generated by
* kernel/firmware/driver.
* Note: This command has been removed and it is only reserved at this
* point to avoid re-using existing command number. The functionality this
* command was planned for has been provided with cleaner design with the
* option to specify additional IEs in NL80211_CMD_TRIGGER_SCAN,
* NL80211_CMD_AUTHENTICATE, NL80211_CMD_ASSOCIATE,
* NL80211_CMD_DEAUTHENTICATE, and NL80211_CMD_DISASSOCIATE.
*
* @NL80211_CMD_GET_SCAN: get scan results
* @NL80211_CMD_TRIGGER_SCAN: trigger a new scan with the given parameters
* %NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the
* probe requests at CCK rate or not. %NL80211_ATTR_BSSID can be used to
* specify a BSSID to scan for; if not included, the wildcard BSSID will
* be used.
* @NL80211_CMD_NEW_SCAN_RESULTS: scan notification (as a reply to
* NL80211_CMD_GET_SCAN and on the "scan" multicast group)
* @NL80211_CMD_SCAN_ABORTED: scan was aborted, for unspecified reasons,
* partial scan results may be available
*
* @NL80211_CMD_START_SCHED_SCAN: start a scheduled scan at certain
* intervals and certain number of cycles, as specified by
* %NL80211_ATTR_SCHED_SCAN_PLANS. If %NL80211_ATTR_SCHED_SCAN_PLANS is
* not specified and only %NL80211_ATTR_SCHED_SCAN_INTERVAL is specified,
* scheduled scan will run in an infinite loop with the specified interval.
* These attributes are mutually exculsive,
* i.e. NL80211_ATTR_SCHED_SCAN_INTERVAL must not be passed if
* NL80211_ATTR_SCHED_SCAN_PLANS is defined.
* If for some reason scheduled scan is aborted by the driver, all scan
* plans are canceled (including scan plans that did not start yet).
* Like with normal scans, if SSIDs (%NL80211_ATTR_SCAN_SSIDS)
* are passed, they are used in the probe requests. For
* broadcast, a broadcast SSID must be passed (ie. an empty
* string). If no SSID is passed, no probe requests are sent and
* a passive scan is performed. %NL80211_ATTR_SCAN_FREQUENCIES,
* if passed, define which channels should be scanned; if not
* passed, all channels allowed for the current regulatory domain
* are used. Extra IEs can also be passed from the userspace by
* using the %NL80211_ATTR_IE attribute. The first cycle of the
* scheduled scan can be delayed by %NL80211_ATTR_SCHED_SCAN_DELAY
* is supplied. If the device supports multiple concurrent scheduled
* scans, it will allow such when the caller provides the flag attribute
* %NL80211_ATTR_SCHED_SCAN_MULTI to indicate user-space support for it.
* @NL80211_CMD_STOP_SCHED_SCAN: stop a scheduled scan. Returns -ENOENT if
* scheduled scan is not running. The caller may assume that as soon
* as the call returns, it is safe to start a new scheduled scan again.
* @NL80211_CMD_SCHED_SCAN_RESULTS: indicates that there are scheduled scan
* results available.
* @NL80211_CMD_SCHED_SCAN_STOPPED: indicates that the scheduled scan has
* stopped. The driver may issue this event at any time during a
* scheduled scan. One reason for stopping the scan is if the hardware
* does not support starting an association or a normal scan while running
* a scheduled scan. This event is also sent when the
* %NL80211_CMD_STOP_SCHED_SCAN command is received or when the interface
* is brought down while a scheduled scan was running.
*
* @NL80211_CMD_GET_SURVEY: get survey resuls, e.g. channel occupation
* or noise level
* @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to
* NL80211_CMD_GET_SURVEY and on the "scan" multicast group)
*
* @NL80211_CMD_SET_PMKSA: Add a PMKSA cache entry using %NL80211_ATTR_MAC
* (for the BSSID), %NL80211_ATTR_PMKID, and optionally %NL80211_ATTR_PMK
* (PMK is used for PTKSA derivation in case of FILS shared key offload) or
* using %NL80211_ATTR_SSID, %NL80211_ATTR_FILS_CACHE_ID,
* %NL80211_ATTR_PMKID, and %NL80211_ATTR_PMK in case of FILS
* authentication where %NL80211_ATTR_FILS_CACHE_ID is the identifier
* advertized by a FILS capable AP identifying the scope of PMKSA in an
* ESS.
* @NL80211_CMD_DEL_PMKSA: Delete a PMKSA cache entry, using %NL80211_ATTR_MAC
* (for the BSSID) and %NL80211_ATTR_PMKID or using %NL80211_ATTR_SSID,
* %NL80211_ATTR_FILS_CACHE_ID, and %NL80211_ATTR_PMKID in case of FILS
* authentication.
* @NL80211_CMD_FLUSH_PMKSA: Flush all PMKSA cache entries.
*
* @NL80211_CMD_REG_CHANGE: indicates to userspace the regulatory domain
* has been changed and provides details of the request information
* that caused the change such as who initiated the regulatory request
* (%NL80211_ATTR_REG_INITIATOR), the wiphy_idx
* (%NL80211_ATTR_REG_ALPHA2) on which the request was made from if
* the initiator was %NL80211_REGDOM_SET_BY_COUNTRY_IE or
* %NL80211_REGDOM_SET_BY_DRIVER, the type of regulatory domain
* set (%NL80211_ATTR_REG_TYPE), if the type of regulatory domain is
* %NL80211_REG_TYPE_COUNTRY the alpha2 to which we have moved on
* to (%NL80211_ATTR_REG_ALPHA2).
* @NL80211_CMD_REG_BEACON_HINT: indicates to userspace that an AP beacon
* has been found while world roaming thus enabling active scan or
* any mode of operation that initiates TX (beacons) on a channel
* where we would not have been able to do either before. As an example
* if you are world roaming (regulatory domain set to world or if your
* driver is using a custom world roaming regulatory domain) and while
* doing a passive scan on the 5 GHz band you find an AP there (if not
* on a DFS channel) you will now be able to actively scan for that AP
* or use AP mode on your card on that same channel. Note that this will
* never be used for channels 1-11 on the 2 GHz band as they are always
* enabled world wide. This beacon hint is only sent if your device had
* either disabled active scanning or beaconing on a channel. We send to
* userspace the wiphy on which we removed a restriction from
* (%NL80211_ATTR_WIPHY) and the channel on which this occurred
* before (%NL80211_ATTR_FREQ_BEFORE) and after (%NL80211_ATTR_FREQ_AFTER)
* the beacon hint was processed.
*
* @NL80211_CMD_AUTHENTICATE: authentication request and notification.
* This command is used both as a command (request to authenticate) and
* as an event on the "mlme" multicast group indicating completion of the
* authentication process.
* When used as a command, %NL80211_ATTR_IFINDEX is used to identify the
* interface. %NL80211_ATTR_MAC is used to specify PeerSTAAddress (and
* BSSID in case of station mode). %NL80211_ATTR_SSID is used to specify
* the SSID (mainly for association, but is included in authentication
* request, too, to help BSS selection. %NL80211_ATTR_WIPHY_FREQ +
* %NL80211_ATTR_WIPHY_FREQ_OFFSET is used to specify the frequence of the
* channel in MHz. %NL80211_ATTR_AUTH_TYPE is used to specify the
* authentication type. %NL80211_ATTR_IE is used to define IEs
* (VendorSpecificInfo, but also including RSN IE and FT IEs) to be added
* to the frame.
* When used as an event, this reports reception of an Authentication
* frame in station and IBSS modes when the local MLME processed the
* frame, i.e., it was for the local STA and was received in correct
* state. This is similar to MLME-AUTHENTICATE.confirm primitive in the
* MLME SAP interface (kernel providing MLME, userspace SME). The
* included %NL80211_ATTR_FRAME attribute contains the management frame
* (including both the header and frame body, but not FCS). This event is
* also used to indicate if the authentication attempt timed out. In that
* case the %NL80211_ATTR_FRAME attribute is replaced with a
* %NL80211_ATTR_TIMED_OUT flag (and %NL80211_ATTR_MAC to indicate which
* pending authentication timed out).
* @NL80211_CMD_ASSOCIATE: association request and notification; like
* NL80211_CMD_AUTHENTICATE but for Association and Reassociation
* (similar to MLME-ASSOCIATE.request, MLME-REASSOCIATE.request,
* MLME-ASSOCIATE.confirm or MLME-REASSOCIATE.confirm primitives). The
* %NL80211_ATTR_PREV_BSSID attribute is used to specify whether the
* request is for the initial association to an ESS (that attribute not
* included) or for reassociation within the ESS (that attribute is
* included).
* @NL80211_CMD_DEAUTHENTICATE: deauthentication request and notification; like
* NL80211_CMD_AUTHENTICATE but for Deauthentication frames (similar to
* MLME-DEAUTHENTICATION.request and MLME-DEAUTHENTICATE.indication
* primitives).
* @NL80211_CMD_DISASSOCIATE: disassociation request and notification; like
* NL80211_CMD_AUTHENTICATE but for Disassociation frames (similar to
* MLME-DISASSOCIATE.request and MLME-DISASSOCIATE.indication primitives).
*
* @NL80211_CMD_MICHAEL_MIC_FAILURE: notification of a locally detected Michael
* MIC (part of TKIP) failure; sent on the "mlme" multicast group; the
* event includes %NL80211_ATTR_MAC to describe the source MAC address of
* the frame with invalid MIC, %NL80211_ATTR_KEY_TYPE to show the key
* type, %NL80211_ATTR_KEY_IDX to indicate the key identifier, and
* %NL80211_ATTR_KEY_SEQ to indicate the TSC value of the frame; this
* event matches with MLME-MICHAELMICFAILURE.indication() primitive
*
* @NL80211_CMD_JOIN_IBSS: Join a new IBSS -- given at least an SSID and a
* FREQ attribute (for the initial frequency if no peer can be found)
* and optionally a MAC (as BSSID) and FREQ_FIXED attribute if those
* should be fixed rather than automatically determined. Can only be
* executed on a network interface that is UP, and fixed BSSID/FREQ
* may be rejected. Another optional parameter is the beacon interval,
* given in the %NL80211_ATTR_BEACON_INTERVAL attribute, which if not
* given defaults to 100 TU (102.4ms).
* @NL80211_CMD_LEAVE_IBSS: Leave the IBSS -- no special arguments, the IBSS is
* determined by the network interface.
*
* @NL80211_CMD_TESTMODE: testmode command, takes a wiphy (or ifindex) attribute
* to identify the device, and the TESTDATA blob attribute to pass through
* to the driver.
*
* @NL80211_CMD_CONNECT: connection request and notification; this command
* requests to connect to a specified network but without separating
* auth and assoc steps. For this, you need to specify the SSID in a
* %NL80211_ATTR_SSID attribute, and can optionally specify the association
* IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE,
* %NL80211_ATTR_USE_MFP, %NL80211_ATTR_MAC, %NL80211_ATTR_WIPHY_FREQ,
* %NL80211_ATTR_WIPHY_FREQ_OFFSET, %NL80211_ATTR_CONTROL_PORT,
* %NL80211_ATTR_CONTROL_PORT_ETHERTYPE,
* %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT,
* %NL80211_ATTR_CONTROL_PORT_OVER_NL80211, %NL80211_ATTR_MAC_HINT, and
* %NL80211_ATTR_WIPHY_FREQ_HINT.
* If included, %NL80211_ATTR_MAC and %NL80211_ATTR_WIPHY_FREQ are
* restrictions on BSS selection, i.e., they effectively prevent roaming
* within the ESS. %NL80211_ATTR_MAC_HINT and %NL80211_ATTR_WIPHY_FREQ_HINT
* can be included to provide a recommendation of the initial BSS while
* allowing the driver to roam to other BSSes within the ESS and also to
* ignore this recommendation if the indicated BSS is not ideal. Only one
* set of BSSID,frequency parameters is used (i.e., either the enforcing
* %NL80211_ATTR_MAC,%NL80211_ATTR_WIPHY_FREQ or the less strict
* %NL80211_ATTR_MAC_HINT and %NL80211_ATTR_WIPHY_FREQ_HINT).
* %NL80211_ATTR_PREV_BSSID can be used to request a reassociation within
* the ESS in case the device is already associated and an association with
* a different BSS is desired.
* Background scan period can optionally be
* specified in %NL80211_ATTR_BG_SCAN_PERIOD,
* if not specified default background scan configuration
* in driver is used and if period value is 0, bg scan will be disabled.
* This attribute is ignored if driver does not support roam scan.
* It is also sent as an event, with the BSSID and response IEs when the
* connection is established or failed to be established. This can be
* determined by the %NL80211_ATTR_STATUS_CODE attribute (0 = success,
* non-zero = failure). If %NL80211_ATTR_TIMED_OUT is included in the
* event, the connection attempt failed due to not being able to initiate
* authentication/association or not receiving a response from the AP.
* Non-zero %NL80211_ATTR_STATUS_CODE value is indicated in that case as
* well to remain backwards compatible.
* @NL80211_CMD_ROAM: Notification indicating the card/driver roamed by itself.
* When a security association was established on an 802.1X network using
* fast transition, this event should be followed by an
* %NL80211_CMD_PORT_AUTHORIZED event.
* Following a %NL80211_CMD_ROAM event userspace can issue
* %NL80211_CMD_GET_SCAN in order to obtain the scan information for the
* new BSS the card/driver roamed to.
* @NL80211_CMD_DISCONNECT: drop a given connection; also used to notify
* userspace that a connection was dropped by the AP or due to other
* reasons, for this the %NL80211_ATTR_DISCONNECTED_BY_AP and
* %NL80211_ATTR_REASON_CODE attributes are used.
*
* @NL80211_CMD_SET_WIPHY_NETNS: Set a wiphy's netns. Note that all devices
* associated with this wiphy must be down and will follow.
*
* @NL80211_CMD_REMAIN_ON_CHANNEL: Request to remain awake on the specified
* channel for the specified amount of time. This can be used to do
* off-channel operations like transmit a Public Action frame and wait for
* a response while being associated to an AP on another channel.
* %NL80211_ATTR_IFINDEX is used to specify which interface (and thus
* radio) is used. %NL80211_ATTR_WIPHY_FREQ is used to specify the
* frequency for the operation.
* %NL80211_ATTR_DURATION is used to specify the duration in milliseconds
* to remain on the channel. This command is also used as an event to
* notify when the requested duration starts (it may take a while for the
* driver to schedule this time due to other concurrent needs for the
* radio).
* When called, this operation returns a cookie (%NL80211_ATTR_COOKIE)
* that will be included with any events pertaining to this request;
* the cookie is also used to cancel the request.
* @NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL: This command can be used to cancel a
* pending remain-on-channel duration if the desired operation has been
* completed prior to expiration of the originally requested duration.
* %NL80211_ATTR_WIPHY or %NL80211_ATTR_IFINDEX is used to specify the
* radio. The %NL80211_ATTR_COOKIE attribute must be given as well to
* uniquely identify the request.
* This command is also used as an event to notify when a requested
* remain-on-channel duration has expired.
*
* @NL80211_CMD_SET_TX_BITRATE_MASK: Set the mask of rates to be used in TX
* rate selection. %NL80211_ATTR_IFINDEX is used to specify the interface
* and @NL80211_ATTR_TX_RATES the set of allowed rates.
*
* @NL80211_CMD_REGISTER_FRAME: Register for receiving certain mgmt frames
* (via @NL80211_CMD_FRAME) for processing in userspace. This command
* requires an interface index, a frame type attribute (optional for
* backward compatibility reasons, if not given assumes action frames)
* and a match attribute containing the first few bytes of the frame
* that should match, e.g. a single byte for only a category match or
* four bytes for vendor frames including the OUI. The registration
* cannot be dropped, but is removed automatically when the netlink
* socket is closed. Multiple registrations can be made.
* The %NL80211_ATTR_RECEIVE_MULTICAST flag attribute can be given if
* %NL80211_EXT_FEATURE_MULTICAST_REGISTRATIONS is available, in which
* case the registration can also be modified to include/exclude the
* flag, rather than requiring unregistration to change it.
* @NL80211_CMD_REGISTER_ACTION: Alias for @NL80211_CMD_REGISTER_FRAME for
* backward compatibility
* @NL80211_CMD_FRAME: Management frame TX request and RX notification. This
* command is used both as a request to transmit a management frame and
* as an event indicating reception of a frame that was not processed in
* kernel code, but is for us (i.e., which may need to be processed in a
* user space application). %NL80211_ATTR_FRAME is used to specify the
* frame contents (including header). %NL80211_ATTR_WIPHY_FREQ is used
* to indicate on which channel the frame is to be transmitted or was
* received. If this channel is not the current channel (remain-on-channel
* or the operational channel) the device will switch to the given channel
* and transmit the frame, optionally waiting for a response for the time
* specified using %NL80211_ATTR_DURATION. When called, this operation
* returns a cookie (%NL80211_ATTR_COOKIE) that will be included with the
* TX status event pertaining to the TX request.
* %NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the
* management frames at CCK rate or not in 2GHz band.
* %NL80211_ATTR_CSA_C_OFFSETS_TX is an array of offsets to CSA
* counters which will be updated to the current value. This attribute
* is used during CSA period.
* For TX on an MLD, the frequency can be omitted and the link ID be
* specified, or if transmitting to a known peer MLD (with MLD addresses
* in the frame) both can be omitted and the link will be selected by
* lower layers.
* For RX notification, %NL80211_ATTR_RX_HW_TIMESTAMP may be included to
* indicate the frame RX timestamp and %NL80211_ATTR_TX_HW_TIMESTAMP may
* be included to indicate the ack TX timestamp.
* @NL80211_CMD_FRAME_WAIT_CANCEL: When an off-channel TX was requested, this
* command may be used with the corresponding cookie to cancel the wait
* time if it is known that it is no longer necessary. This command is
* also sent as an event whenever the driver has completed the off-channel
* wait time.
* @NL80211_CMD_ACTION: Alias for @NL80211_CMD_FRAME for backward compatibility.
* @NL80211_CMD_FRAME_TX_STATUS: Report TX status of a management frame
* transmitted with %NL80211_CMD_FRAME. %NL80211_ATTR_COOKIE identifies
* the TX command and %NL80211_ATTR_FRAME includes the contents of the
* frame. %NL80211_ATTR_ACK flag is included if the recipient acknowledged
* the frame. %NL80211_ATTR_TX_HW_TIMESTAMP may be included to indicate the
* tx timestamp and %NL80211_ATTR_RX_HW_TIMESTAMP may be included to
* indicate the ack RX timestamp.
* @NL80211_CMD_ACTION_TX_STATUS: Alias for @NL80211_CMD_FRAME_TX_STATUS for
* backward compatibility.
*
* @NL80211_CMD_SET_POWER_SAVE: Set powersave, using %NL80211_ATTR_PS_STATE
* @NL80211_CMD_GET_POWER_SAVE: Get powersave status in %NL80211_ATTR_PS_STATE
*
* @NL80211_CMD_SET_CQM: Connection quality monitor configuration. This command
* is used to configure connection quality monitoring notification trigger
* levels.
* @NL80211_CMD_NOTIFY_CQM: Connection quality monitor notification. This
* command is used as an event to indicate the that a trigger level was
* reached.
* @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ
* and the attributes determining channel width) the given interface
* (identifed by %NL80211_ATTR_IFINDEX) shall operate on.
* In case multiple channels are supported by the device, the mechanism
* with which it switches channels is implementation-defined.
* When a monitor interface is given, it can only switch channel while
* no other interfaces are operating to avoid disturbing the operation
* of any other interfaces, and other interfaces will again take
* precedence when they are used.
*
* @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface
* (no longer supported).
*
* @NL80211_CMD_SET_MULTICAST_TO_UNICAST: Configure if this AP should perform
* multicast to unicast conversion. When enabled, all multicast packets
* with ethertype ARP, IPv4 or IPv6 (possibly within an 802.1Q header)
* will be sent out to each station once with the destination (multicast)
* MAC address replaced by the station's MAC address. Note that this may
* break certain expectations of the receiver, e.g. the ability to drop
* unicast IP packets encapsulated in multicast L2 frames, or the ability
* to not send destination unreachable messages in such cases.
* This can only be toggled per BSS. Configure this on an interface of
* type %NL80211_IFTYPE_AP. It applies to all its VLAN interfaces
* (%NL80211_IFTYPE_AP_VLAN), except for those in 4addr (WDS) mode.
* If %NL80211_ATTR_MULTICAST_TO_UNICAST_ENABLED is not present with this
* command, the feature is disabled.
*
* @NL80211_CMD_JOIN_MESH: Join a mesh. The mesh ID must be given, and initial
* mesh config parameters may be given.
* @NL80211_CMD_LEAVE_MESH: Leave the mesh network -- no special arguments, the
* network is determined by the network interface.
*
* @NL80211_CMD_UNPROT_DEAUTHENTICATE: Unprotected deauthentication frame
* notification. This event is used to indicate that an unprotected
* deauthentication frame was dropped when MFP is in use.
* @NL80211_CMD_UNPROT_DISASSOCIATE: Unprotected disassociation frame
* notification. This event is used to indicate that an unprotected
* disassociation frame was dropped when MFP is in use.
*
* @NL80211_CMD_NEW_PEER_CANDIDATE: Notification on the reception of a
* beacon or probe response from a compatible mesh peer. This is only
* sent while no station information (sta_info) exists for the new peer
* candidate and when @NL80211_MESH_SETUP_USERSPACE_AUTH,
* @NL80211_MESH_SETUP_USERSPACE_AMPE, or
* @NL80211_MESH_SETUP_USERSPACE_MPM is set. On reception of this
* notification, userspace may decide to create a new station
* (@NL80211_CMD_NEW_STATION). To stop this notification from
* reoccurring, the userspace authentication daemon may want to create the
* new station with the AUTHENTICATED flag unset and maybe change it later
* depending on the authentication result.
*
* @NL80211_CMD_GET_WOWLAN: get Wake-on-Wireless-LAN (WoWLAN) settings.
* @NL80211_CMD_SET_WOWLAN: set Wake-on-Wireless-LAN (WoWLAN) settings.
* Since wireless is more complex than wired ethernet, it supports
* various triggers. These triggers can be configured through this
* command with the %NL80211_ATTR_WOWLAN_TRIGGERS attribute. For
* more background information, see
* https://wireless.wiki.kernel.org/en/users/Documentation/WoWLAN.
* The @NL80211_CMD_SET_WOWLAN command can also be used as a notification
* from the driver reporting the wakeup reason. In this case, the
* @NL80211_ATTR_WOWLAN_TRIGGERS attribute will contain the reason
* for the wakeup, if it was caused by wireless. If it is not present
* in the wakeup notification, the wireless device didn't cause the
* wakeup but reports that it was woken up.
*
* @NL80211_CMD_SET_REKEY_OFFLOAD: This command is used give the driver
* the necessary information for supporting GTK rekey offload. This
* feature is typically used during WoWLAN. The configuration data
* is contained in %NL80211_ATTR_REKEY_DATA (which is nested and
* contains the data in sub-attributes). After rekeying happened,
* this command may also be sent by the driver as an MLME event to
* inform userspace of the new replay counter.
*
* @NL80211_CMD_PMKSA_CANDIDATE: This is used as an event to inform userspace
* of PMKSA caching dandidates.
*
* @NL80211_CMD_TDLS_OPER: Perform a high-level TDLS command (e.g. link setup).
* In addition, this can be used as an event to request userspace to take
* actions on TDLS links (set up a new link or tear down an existing one).
* In such events, %NL80211_ATTR_TDLS_OPERATION indicates the requested
* operation, %NL80211_ATTR_MAC contains the peer MAC address, and
* %NL80211_ATTR_REASON_CODE the reason code to be used (only with
* %NL80211_TDLS_TEARDOWN).
* @NL80211_CMD_TDLS_MGMT: Send a TDLS management frame. The
* %NL80211_ATTR_TDLS_ACTION attribute determines the type of frame to be
* sent. Public Action codes (802.11-2012 8.1.5.1) will be sent as
* 802.11 management frames, while TDLS action codes (802.11-2012
* 8.5.13.1) will be encapsulated and sent as data frames. The currently
* supported Public Action code is %WLAN_PUB_ACTION_TDLS_DISCOVER_RES
* and the currently supported TDLS actions codes are given in
* &enum ieee80211_tdls_actioncode.
*
* @NL80211_CMD_UNEXPECTED_FRAME: Used by an application controlling an AP
* (or GO) interface (i.e. hostapd) to ask for unexpected frames to
* implement sending deauth to stations that send unexpected class 3
* frames. Also used as the event sent by the kernel when such a frame
* is received.
* For the event, the %NL80211_ATTR_MAC attribute carries the TA and
* other attributes like the interface index are present.
* If used as the command it must have an interface index and you can
* only unsubscribe from the event by closing the socket. Subscription
* is also for %NL80211_CMD_UNEXPECTED_4ADDR_FRAME events.
*
* @NL80211_CMD_UNEXPECTED_4ADDR_FRAME: Sent as an event indicating that the
* associated station identified by %NL80211_ATTR_MAC sent a 4addr frame
* and wasn't already in a 4-addr VLAN. The event will be sent similarly
* to the %NL80211_CMD_UNEXPECTED_FRAME event, to the same listener.
*
* @NL80211_CMD_PROBE_CLIENT: Probe an associated station on an AP interface
* by sending a null data frame to it and reporting when the frame is
* acknowleged. This is used to allow timing out inactive clients. Uses
* %NL80211_ATTR_IFINDEX and %NL80211_ATTR_MAC. The command returns a
* direct reply with an %NL80211_ATTR_COOKIE that is later used to match
* up the event with the request. The event includes the same data and
* has %NL80211_ATTR_ACK set if the frame was ACKed.
*
* @NL80211_CMD_REGISTER_BEACONS: Register this socket to receive beacons from
* other BSSes when any interfaces are in AP mode. This helps implement
* OLBC handling in hostapd. Beacons are reported in %NL80211_CMD_FRAME
* messages. Note that per PHY only one application may register.
*
* @NL80211_CMD_SET_NOACK_MAP: sets a bitmap for the individual TIDs whether
* No Acknowledgement Policy should be applied.
*
* @NL80211_CMD_CH_SWITCH_NOTIFY: An AP or GO may decide to switch channels
* independently of the userspace SME, send this event indicating
* %NL80211_ATTR_IFINDEX is now on %NL80211_ATTR_WIPHY_FREQ and the
* attributes determining channel width. This indication may also be
* sent when a remotely-initiated switch (e.g., when a STA receives a CSA
* from the remote AP) is completed;
*
* @NL80211_CMD_CH_SWITCH_STARTED_NOTIFY: Notify that a channel switch
* has been started on an interface, regardless of the initiator
* (ie. whether it was requested from a remote device or
* initiated on our own). It indicates that
* %NL80211_ATTR_IFINDEX will be on %NL80211_ATTR_WIPHY_FREQ
* after %NL80211_ATTR_CH_SWITCH_COUNT TBTT's. The userspace may
* decide to react to this indication by requesting other
* interfaces to change channel as well.
*
* @NL80211_CMD_START_P2P_DEVICE: Start the given P2P Device, identified by
* its %NL80211_ATTR_WDEV identifier. It must have been created with
* %NL80211_CMD_NEW_INTERFACE previously. After it has been started, the
* P2P Device can be used for P2P operations, e.g. remain-on-channel and
* public action frame TX.
* @NL80211_CMD_STOP_P2P_DEVICE: Stop the given P2P Device, identified by
* its %NL80211_ATTR_WDEV identifier.
*
* @NL80211_CMD_CONN_FAILED: connection request to an AP failed; used to
* notify userspace that AP has rejected the connection request from a
* station, due to particular reason. %NL80211_ATTR_CONN_FAILED_REASON
* is used for this.
*
* @NL80211_CMD_SET_MCAST_RATE: Change the rate used to send multicast frames
* for IBSS or MESH vif.
*
* @NL80211_CMD_SET_MAC_ACL: sets ACL for MAC address based access control.
* This is to be used with the drivers advertising the support of MAC
* address based access control. List of MAC addresses is passed in
* %NL80211_ATTR_MAC_ADDRS and ACL policy is passed in
* %NL80211_ATTR_ACL_POLICY. Driver will enable ACL with this list, if it
* is not already done. The new list will replace any existing list. Driver
* will clear its ACL when the list of MAC addresses passed is empty. This
* command is used in AP/P2P GO mode. Driver has to make sure to clear its
* ACL list during %NL80211_CMD_STOP_AP.
*
* @NL80211_CMD_RADAR_DETECT: Start a Channel availability check (CAC). Once
* a radar is detected or the channel availability scan (CAC) has finished
* or was aborted, or a radar was detected, usermode will be notified with
* this event. This command is also used to notify userspace about radars
* while operating on this channel.
* %NL80211_ATTR_RADAR_EVENT is used to inform about the type of the
* event.
*
* @NL80211_CMD_GET_PROTOCOL_FEATURES: Get global nl80211 protocol features,
* i.e. features for the nl80211 protocol rather than device features.
* Returns the features in the %NL80211_ATTR_PROTOCOL_FEATURES bitmap.
*
* @NL80211_CMD_UPDATE_FT_IES: Pass down the most up-to-date Fast Transition
* Information Element to the WLAN driver
*
* @NL80211_CMD_FT_EVENT: Send a Fast transition event from the WLAN driver
* to the supplicant. This will carry the target AP's MAC address along
* with the relevant Information Elements. This event is used to report
* received FT IEs (MDIE, FTIE, RSN IE, TIE, RICIE).
*
* @NL80211_CMD_CRIT_PROTOCOL_START: Indicates user-space will start running
* a critical protocol that needs more reliability in the connection to
* complete.
*
* @NL80211_CMD_CRIT_PROTOCOL_STOP: Indicates the connection reliability can
* return back to normal.
*
* @NL80211_CMD_GET_COALESCE: Get currently supported coalesce rules.
* @NL80211_CMD_SET_COALESCE: Configure coalesce rules or clear existing rules.
*
* @NL80211_CMD_CHANNEL_SWITCH: Perform a channel switch by announcing the
* new channel information (Channel Switch Announcement - CSA)
* in the beacon for some time (as defined in the
* %NL80211_ATTR_CH_SWITCH_COUNT parameter) and then change to the
* new channel. Userspace provides the new channel information (using
* %NL80211_ATTR_WIPHY_FREQ and the attributes determining channel
* width). %NL80211_ATTR_CH_SWITCH_BLOCK_TX may be supplied to inform
* other station that transmission must be blocked until the channel
* switch is complete.
*
* @NL80211_CMD_VENDOR: Vendor-specified command/event. The command is specified
* by the %NL80211_ATTR_VENDOR_ID attribute and a sub-command in
* %NL80211_ATTR_VENDOR_SUBCMD. Parameter(s) can be transported in
* %NL80211_ATTR_VENDOR_DATA.
* For feature advertisement, the %NL80211_ATTR_VENDOR_DATA attribute is
* used in the wiphy data as a nested attribute containing descriptions
* (&struct nl80211_vendor_cmd_info) of the supported vendor commands.
* This may also be sent as an event with the same attributes.
*
* @NL80211_CMD_SET_QOS_MAP: Set Interworking QoS mapping for IP DSCP values.
* The QoS mapping information is included in %NL80211_ATTR_QOS_MAP. If
* that attribute is not included, QoS mapping is disabled. Since this
* QoS mapping is relevant for IP packets, it is only valid during an
* association. This is cleared on disassociation and AP restart.
*
* @NL80211_CMD_ADD_TX_TS: Ask the kernel to add a traffic stream for the given
* %NL80211_ATTR_TSID and %NL80211_ATTR_MAC with %NL80211_ATTR_USER_PRIO
* and %NL80211_ATTR_ADMITTED_TIME parameters.
* Note that the action frame handshake with the AP shall be handled by
* userspace via the normal management RX/TX framework, this only sets
* up the TX TS in the driver/device.
* If the admitted time attribute is not added then the request just checks
* if a subsequent setup could be successful, the intent is to use this to
* avoid setting up a session with the AP when local restrictions would
* make that impossible. However, the subsequent "real" setup may still
* fail even if the check was successful.
* @NL80211_CMD_DEL_TX_TS: Remove an existing TS with the %NL80211_ATTR_TSID
* and %NL80211_ATTR_MAC parameters. It isn't necessary to call this
* before removing a station entry entirely, or before disassociating
* or similar, cleanup will happen in the driver/device in this case.
*
* @NL80211_CMD_GET_MPP: Get mesh path attributes for mesh proxy path to
* destination %NL80211_ATTR_MAC on the interface identified by
* %NL80211_ATTR_IFINDEX.
*
* @NL80211_CMD_JOIN_OCB: Join the OCB network. The center frequency and
* bandwidth of a channel must be given.
* @NL80211_CMD_LEAVE_OCB: Leave the OCB network -- no special arguments, the
* network is determined by the network interface.
*
* @NL80211_CMD_TDLS_CHANNEL_SWITCH: Start channel-switching with a TDLS peer,
* identified by the %NL80211_ATTR_MAC parameter. A target channel is
* provided via %NL80211_ATTR_WIPHY_FREQ and other attributes determining
* channel width/type. The target operating class is given via
* %NL80211_ATTR_OPER_CLASS.
* The driver is responsible for continually initiating channel-switching
* operations and returning to the base channel for communication with the
* AP.
* @NL80211_CMD_TDLS_CANCEL_CHANNEL_SWITCH: Stop channel-switching with a TDLS
* peer given by %NL80211_ATTR_MAC. Both peers must be on the base channel
* when this command completes.
*
* @NL80211_CMD_WIPHY_REG_CHANGE: Similar to %NL80211_CMD_REG_CHANGE, but used
* as an event to indicate changes for devices with wiphy-specific regdom
* management.
*
* @NL80211_CMD_ABORT_SCAN: Stop an ongoing scan. Returns -ENOENT if a scan is
* not running. The driver indicates the status of the scan through
* cfg80211_scan_done().
*
* @NL80211_CMD_START_NAN: Start NAN operation, identified by its
* %NL80211_ATTR_WDEV interface. This interface must have been
* previously created with %NL80211_CMD_NEW_INTERFACE. After it
* has been started, the NAN interface will create or join a
* cluster. This command must have a valid
* %NL80211_ATTR_NAN_MASTER_PREF attribute and optional
* %NL80211_ATTR_BANDS attributes. If %NL80211_ATTR_BANDS is
* omitted or set to 0, it means don't-care and the device will
* decide what to use. After this command NAN functions can be
* added.
* @NL80211_CMD_STOP_NAN: Stop the NAN operation, identified by
* its %NL80211_ATTR_WDEV interface.
* @NL80211_CMD_ADD_NAN_FUNCTION: Add a NAN function. The function is defined
* with %NL80211_ATTR_NAN_FUNC nested attribute. When called, this
* operation returns the strictly positive and unique instance id
* (%NL80211_ATTR_NAN_FUNC_INST_ID) and a cookie (%NL80211_ATTR_COOKIE)
* of the function upon success.
* Since instance ID's can be re-used, this cookie is the right
* way to identify the function. This will avoid races when a termination
* event is handled by the user space after it has already added a new
* function that got the same instance id from the kernel as the one
* which just terminated.
* This cookie may be used in NAN events even before the command
* returns, so userspace shouldn't process NAN events until it processes
* the response to this command.
* Look at %NL80211_ATTR_SOCKET_OWNER as well.
* @NL80211_CMD_DEL_NAN_FUNCTION: Delete a NAN function by cookie.
* This command is also used as a notification sent when a NAN function is
* terminated. This will contain a %NL80211_ATTR_NAN_FUNC_INST_ID
* and %NL80211_ATTR_COOKIE attributes.
* @NL80211_CMD_CHANGE_NAN_CONFIG: Change current NAN
* configuration. NAN must be operational (%NL80211_CMD_START_NAN
* was executed). It must contain at least one of the following
* attributes: %NL80211_ATTR_NAN_MASTER_PREF,
* %NL80211_ATTR_BANDS. If %NL80211_ATTR_BANDS is omitted, the
* current configuration is not changed. If it is present but
* set to zero, the configuration is changed to don't-care
* (i.e. the device can decide what to do).
* @NL80211_CMD_NAN_FUNC_MATCH: Notification sent when a match is reported.
* This will contain a %NL80211_ATTR_NAN_MATCH nested attribute and
* %NL80211_ATTR_COOKIE.
*
* @NL80211_CMD_UPDATE_CONNECT_PARAMS: Update one or more connect parameters
* for subsequent roaming cases if the driver or firmware uses internal
* BSS selection. This command can be issued only while connected and it
* does not result in a change for the current association. Currently,
* only the %NL80211_ATTR_IE data is used and updated with this command.
*
* @NL80211_CMD_SET_PMK: For offloaded 4-Way handshake, set the PMK or PMK-R0
* for the given authenticator address (specified with %NL80211_ATTR_MAC).
* When %NL80211_ATTR_PMKR0_NAME is set, %NL80211_ATTR_PMK specifies the
* PMK-R0, otherwise it specifies the PMK.
* @NL80211_CMD_DEL_PMK: For offloaded 4-Way handshake, delete the previously
* configured PMK for the authenticator address identified by
* %NL80211_ATTR_MAC.
* @NL80211_CMD_PORT_AUTHORIZED: An event that indicates an 802.1X FT roam was
* completed successfully. Drivers that support 4 way handshake offload
* should send this event after indicating 802.1X FT assocation with
* %NL80211_CMD_ROAM. If the 4 way handshake failed %NL80211_CMD_DISCONNECT
* should be indicated instead.
* @NL80211_CMD_CONTROL_PORT_FRAME: Control Port (e.g. PAE) frame TX request
* and RX notification. This command is used both as a request to transmit
* a control port frame and as a notification that a control port frame
* has been received. %NL80211_ATTR_FRAME is used to specify the
* frame contents. The frame is the raw EAPoL data, without ethernet or
* 802.11 headers.
* For an MLD transmitter, the %NL80211_ATTR_MLO_LINK_ID may be given and
* its effect will depend on the destination: If the destination is known
* to be an MLD, this will be used as a hint to select the link to transmit
* the frame on. If the destination is not an MLD, this will select both
* the link to transmit on and the source address will be set to the link
* address of that link.
* When used as an event indication %NL80211_ATTR_CONTROL_PORT_ETHERTYPE,
* %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT and %NL80211_ATTR_MAC are added
* indicating the protocol type of the received frame; whether the frame
* was received unencrypted and the MAC address of the peer respectively.
*
* @NL80211_CMD_RELOAD_REGDB: Request that the regdb firmware file is reloaded.
*
* @NL80211_CMD_EXTERNAL_AUTH: This interface is exclusively defined for host
* drivers that do not define separate commands for authentication and
* association, but rely on user space for the authentication to happen.
* This interface acts both as the event request (driver to user space)
* to trigger the authentication and command response (userspace to
* driver) to indicate the authentication status.
*
* User space uses the %NL80211_CMD_CONNECT command to the host driver to
* trigger a connection. The host driver selects a BSS and further uses
* this interface to offload only the authentication part to the user
* space. Authentication frames are passed between the driver and user
* space through the %NL80211_CMD_FRAME interface. Host driver proceeds
* further with the association after getting successful authentication
* status. User space indicates the authentication status through
* %NL80211_ATTR_STATUS_CODE attribute in %NL80211_CMD_EXTERNAL_AUTH
* command interface.
*
* Host driver sends MLD address of the AP with %NL80211_ATTR_MLD_ADDR in
* %NL80211_CMD_EXTERNAL_AUTH event to indicate user space to enable MLO
* during the authentication offload in STA mode while connecting to MLD
* APs. Host driver should check %NL80211_ATTR_MLO_SUPPORT flag capability
* in %NL80211_CMD_CONNECT to know whether the user space supports enabling
* MLO during the authentication offload or not.
* User space should enable MLO during the authentication only when it
* receives the AP MLD address in authentication offload request. User
* space shouldn't enable MLO when the authentication offload request
* doesn't indicate the AP MLD address even if the AP is MLO capable.
* User space should use %NL80211_ATTR_MLD_ADDR as peer's MLD address and
* interface address identified by %NL80211_ATTR_IFINDEX as self MLD
* address. User space and host driver to use MLD addresses in RA, TA and
* BSSID fields of the frames between them, and host driver translates the
* MLD addresses to/from link addresses based on the link chosen for the
* authentication.
*
* Host driver reports this status on an authentication failure to the
* user space through the connect result as the user space would have
* initiated the connection through the connect request.
*
* @NL80211_CMD_STA_OPMODE_CHANGED: An event that notify station's
* ht opmode or vht opmode changes using any of %NL80211_ATTR_SMPS_MODE,
* %NL80211_ATTR_CHANNEL_WIDTH,%NL80211_ATTR_NSS attributes with its
* address(specified in %NL80211_ATTR_MAC).
*
* @NL80211_CMD_GET_FTM_RESPONDER_STATS: Retrieve FTM responder statistics, in
* the %NL80211_ATTR_FTM_RESPONDER_STATS attribute.
*
* @NL80211_CMD_PEER_MEASUREMENT_START: start a (set of) peer measurement(s)
* with the given parameters, which are encapsulated in the nested
* %NL80211_ATTR_PEER_MEASUREMENTS attribute. Optionally, MAC address
* randomization may be enabled and configured by specifying the
* %NL80211_ATTR_MAC and %NL80211_ATTR_MAC_MASK attributes.
* If a timeout is requested, use the %NL80211_ATTR_TIMEOUT attribute.
* A u64 cookie for further %NL80211_ATTR_COOKIE use is returned in
* the netlink extended ack message.
*
* To cancel a measurement, close the socket that requested it.
*
* Measurement results are reported to the socket that requested the
* measurement using @NL80211_CMD_PEER_MEASUREMENT_RESULT when they
* become available, so applications must ensure a large enough socket
* buffer size.
*
* Depending on driver support it may or may not be possible to start
* multiple concurrent measurements.
* @NL80211_CMD_PEER_MEASUREMENT_RESULT: This command number is used for the
* result notification from the driver to the requesting socket.
* @NL80211_CMD_PEER_MEASUREMENT_COMPLETE: Notification only, indicating that
* the measurement completed, using the measurement cookie
* (%NL80211_ATTR_COOKIE).
*
* @NL80211_CMD_NOTIFY_RADAR: Notify the kernel that a radar signal was
* detected and reported by a neighboring device on the channel
* indicated by %NL80211_ATTR_WIPHY_FREQ and other attributes
* determining the width and type.
*
* @NL80211_CMD_UPDATE_OWE_INFO: This interface allows the host driver to
* offload OWE processing to user space. This intends to support
* OWE AKM by the host drivers that implement SME but rely
* on the user space for the cryptographic/DH IE processing in AP mode.
*
* @NL80211_CMD_PROBE_MESH_LINK: The requirement for mesh link metric
* refreshing, is that from one mesh point we be able to send some data
* frames to other mesh points which are not currently selected as a
* primary traffic path, but which are only 1 hop away. The absence of
* the primary path to the chosen node makes it necessary to apply some
* form of marking on a chosen packet stream so that the packets can be
* properly steered to the selected node for testing, and not by the
* regular mesh path lookup. Further, the packets must be of type data
* so that the rate control (often embedded in firmware) is used for
* rate selection.
*
* Here attribute %NL80211_ATTR_MAC is used to specify connected mesh
* peer MAC address and %NL80211_ATTR_FRAME is used to specify the frame
* content. The frame is ethernet data.
*
* @NL80211_CMD_SET_TID_CONFIG: Data frame TID specific configuration
* is passed using %NL80211_ATTR_TID_CONFIG attribute.
*
* @NL80211_CMD_UNPROT_BEACON: Unprotected or incorrectly protected Beacon
* frame. This event is used to indicate that a received Beacon frame was
* dropped because it did not include a valid MME MIC while beacon
* protection was enabled (BIGTK configured in station mode).
*
* @NL80211_CMD_CONTROL_PORT_FRAME_TX_STATUS: Report TX status of a control
* port frame transmitted with %NL80211_CMD_CONTROL_PORT_FRAME.
* %NL80211_ATTR_COOKIE identifies the TX command and %NL80211_ATTR_FRAME
* includes the contents of the frame. %NL80211_ATTR_ACK flag is included
* if the recipient acknowledged the frame.
*
* @NL80211_CMD_SET_SAR_SPECS: SAR power limitation configuration is
* passed using %NL80211_ATTR_SAR_SPEC. %NL80211_ATTR_WIPHY is used to
* specify the wiphy index to be applied to.
*
* @NL80211_CMD_OBSS_COLOR_COLLISION: This notification is sent out whenever
* mac80211/drv detects a bss color collision.
*
* @NL80211_CMD_COLOR_CHANGE_REQUEST: This command is used to indicate that
* userspace wants to change the BSS color.
*
* @NL80211_CMD_COLOR_CHANGE_STARTED: Notify userland, that a color change has
* started
*
* @NL80211_CMD_COLOR_CHANGE_ABORTED: Notify userland, that the color change has
* been aborted
*
* @NL80211_CMD_COLOR_CHANGE_COMPLETED: Notify userland that the color change
* has completed
*
* @NL80211_CMD_SET_FILS_AAD: Set FILS AAD data to the driver using -
* &NL80211_ATTR_MAC - for STA MAC address
* &NL80211_ATTR_FILS_KEK - for KEK
* &NL80211_ATTR_FILS_NONCES - for FILS Nonces
* (STA Nonce 16 bytes followed by AP Nonce 16 bytes)
*
* @NL80211_CMD_ASSOC_COMEBACK: notification about an association
* temporal rejection with comeback. The event includes %NL80211_ATTR_MAC
* to describe the BSSID address of the AP and %NL80211_ATTR_TIMEOUT to
* specify the timeout value.
*
* @NL80211_CMD_ADD_LINK: Add a new link to an interface. The
* %NL80211_ATTR_MLO_LINK_ID attribute is used for the new link.
* @NL80211_CMD_REMOVE_LINK: Remove a link from an interface. This may come
* without %NL80211_ATTR_MLO_LINK_ID as an easy way to remove all links
* in preparation for e.g. roaming to a regular (non-MLO) AP.
*
* @NL80211_CMD_ADD_LINK_STA: Add a link to an MLD station
* @NL80211_CMD_MODIFY_LINK_STA: Modify a link of an MLD station
* @NL80211_CMD_REMOVE_LINK_STA: Remove a link of an MLD station
*
* @NL80211_CMD_SET_HW_TIMESTAMP: Enable/disable HW timestamping of Timing
* measurement and Fine timing measurement frames. If %NL80211_ATTR_MAC
* is included, enable/disable HW timestamping only for frames to/from the
* specified MAC address. Otherwise enable/disable HW timestamping for
* all TM/FTM frames (including ones that were enabled with specific MAC
* address). If %NL80211_ATTR_HW_TIMESTAMP_ENABLED is not included, disable
* HW timestamping.
* The number of peers that HW timestamping can be enabled for concurrently
* is indicated by %NL80211_ATTR_MAX_HW_TIMESTAMP_PEERS.
*
* @NL80211_CMD_MAX: highest used command number
* @__NL80211_CMD_AFTER_LAST: internal use
*/
enum nl80211_commands {
/* don't change the order or add anything between, this is ABI! */
NL80211_CMD_UNSPEC,
NL80211_CMD_GET_WIPHY, /* can dump */
NL80211_CMD_SET_WIPHY,
NL80211_CMD_NEW_WIPHY,
NL80211_CMD_DEL_WIPHY,
NL80211_CMD_GET_INTERFACE, /* can dump */
NL80211_CMD_SET_INTERFACE,
NL80211_CMD_NEW_INTERFACE,
NL80211_CMD_DEL_INTERFACE,
NL80211_CMD_GET_KEY,
NL80211_CMD_SET_KEY,
NL80211_CMD_NEW_KEY,
NL80211_CMD_DEL_KEY,
NL80211_CMD_GET_BEACON,
NL80211_CMD_SET_BEACON,
NL80211_CMD_START_AP,
NL80211_CMD_NEW_BEACON = NL80211_CMD_START_AP,
NL80211_CMD_STOP_AP,
NL80211_CMD_DEL_BEACON = NL80211_CMD_STOP_AP,
NL80211_CMD_GET_STATION,
NL80211_CMD_SET_STATION,
NL80211_CMD_NEW_STATION,
NL80211_CMD_DEL_STATION,
NL80211_CMD_GET_MPATH,
NL80211_CMD_SET_MPATH,
NL80211_CMD_NEW_MPATH,
NL80211_CMD_DEL_MPATH,
NL80211_CMD_SET_BSS,
NL80211_CMD_SET_REG,
NL80211_CMD_REQ_SET_REG,
NL80211_CMD_GET_MESH_CONFIG,
NL80211_CMD_SET_MESH_CONFIG,
NL80211_CMD_SET_MGMT_EXTRA_IE /* reserved; not used */,
NL80211_CMD_GET_REG,
NL80211_CMD_GET_SCAN,
NL80211_CMD_TRIGGER_SCAN,
NL80211_CMD_NEW_SCAN_RESULTS,
NL80211_CMD_SCAN_ABORTED,
NL80211_CMD_REG_CHANGE,
NL80211_CMD_AUTHENTICATE,
NL80211_CMD_ASSOCIATE,
NL80211_CMD_DEAUTHENTICATE,
NL80211_CMD_DISASSOCIATE,
NL80211_CMD_MICHAEL_MIC_FAILURE,
NL80211_CMD_REG_BEACON_HINT,
NL80211_CMD_JOIN_IBSS,
NL80211_CMD_LEAVE_IBSS,
NL80211_CMD_TESTMODE,
NL80211_CMD_CONNECT,
NL80211_CMD_ROAM,
NL80211_CMD_DISCONNECT,
NL80211_CMD_SET_WIPHY_NETNS,
NL80211_CMD_GET_SURVEY,
NL80211_CMD_NEW_SURVEY_RESULTS,
NL80211_CMD_SET_PMKSA,
NL80211_CMD_DEL_PMKSA,
NL80211_CMD_FLUSH_PMKSA,
NL80211_CMD_REMAIN_ON_CHANNEL,
NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL,
NL80211_CMD_SET_TX_BITRATE_MASK,
NL80211_CMD_REGISTER_FRAME,
NL80211_CMD_REGISTER_ACTION = NL80211_CMD_REGISTER_FRAME,
NL80211_CMD_FRAME,
NL80211_CMD_ACTION = NL80211_CMD_FRAME,
NL80211_CMD_FRAME_TX_STATUS,
NL80211_CMD_ACTION_TX_STATUS = NL80211_CMD_FRAME_TX_STATUS,
NL80211_CMD_SET_POWER_SAVE,
NL80211_CMD_GET_POWER_SAVE,
NL80211_CMD_SET_CQM,
NL80211_CMD_NOTIFY_CQM,
NL80211_CMD_SET_CHANNEL,
NL80211_CMD_SET_WDS_PEER,
NL80211_CMD_FRAME_WAIT_CANCEL,
NL80211_CMD_JOIN_MESH,
NL80211_CMD_LEAVE_MESH,
NL80211_CMD_UNPROT_DEAUTHENTICATE,
NL80211_CMD_UNPROT_DISASSOCIATE,
NL80211_CMD_NEW_PEER_CANDIDATE,
NL80211_CMD_GET_WOWLAN,
NL80211_CMD_SET_WOWLAN,
NL80211_CMD_START_SCHED_SCAN,
NL80211_CMD_STOP_SCHED_SCAN,
NL80211_CMD_SCHED_SCAN_RESULTS,
NL80211_CMD_SCHED_SCAN_STOPPED,
NL80211_CMD_SET_REKEY_OFFLOAD,
NL80211_CMD_PMKSA_CANDIDATE,
NL80211_CMD_TDLS_OPER,
NL80211_CMD_TDLS_MGMT,
NL80211_CMD_UNEXPECTED_FRAME,
NL80211_CMD_PROBE_CLIENT,
NL80211_CMD_REGISTER_BEACONS,
NL80211_CMD_UNEXPECTED_4ADDR_FRAME,
NL80211_CMD_SET_NOACK_MAP,
NL80211_CMD_CH_SWITCH_NOTIFY,
NL80211_CMD_START_P2P_DEVICE,
NL80211_CMD_STOP_P2P_DEVICE,
NL80211_CMD_CONN_FAILED,
NL80211_CMD_SET_MCAST_RATE,
NL80211_CMD_SET_MAC_ACL,
NL80211_CMD_RADAR_DETECT,
NL80211_CMD_GET_PROTOCOL_FEATURES,
NL80211_CMD_UPDATE_FT_IES,
NL80211_CMD_FT_EVENT,
NL80211_CMD_CRIT_PROTOCOL_START,
NL80211_CMD_CRIT_PROTOCOL_STOP,
NL80211_CMD_GET_COALESCE,
NL80211_CMD_SET_COALESCE,
NL80211_CMD_CHANNEL_SWITCH,
NL80211_CMD_VENDOR,
NL80211_CMD_SET_QOS_MAP,
NL80211_CMD_ADD_TX_TS,
NL80211_CMD_DEL_TX_TS,
NL80211_CMD_GET_MPP,
NL80211_CMD_JOIN_OCB,
NL80211_CMD_LEAVE_OCB,
NL80211_CMD_CH_SWITCH_STARTED_NOTIFY,
NL80211_CMD_TDLS_CHANNEL_SWITCH,
NL80211_CMD_TDLS_CANCEL_CHANNEL_SWITCH,
NL80211_CMD_WIPHY_REG_CHANGE,
NL80211_CMD_ABORT_SCAN,
NL80211_CMD_START_NAN,
NL80211_CMD_STOP_NAN,
NL80211_CMD_ADD_NAN_FUNCTION,
NL80211_CMD_DEL_NAN_FUNCTION,
NL80211_CMD_CHANGE_NAN_CONFIG,
NL80211_CMD_NAN_MATCH,
NL80211_CMD_SET_MULTICAST_TO_UNICAST,
NL80211_CMD_UPDATE_CONNECT_PARAMS,
NL80211_CMD_SET_PMK,
NL80211_CMD_DEL_PMK,
NL80211_CMD_PORT_AUTHORIZED,
NL80211_CMD_RELOAD_REGDB,
NL80211_CMD_EXTERNAL_AUTH,
NL80211_CMD_STA_OPMODE_CHANGED,
NL80211_CMD_CONTROL_PORT_FRAME,
NL80211_CMD_GET_FTM_RESPONDER_STATS,
NL80211_CMD_PEER_MEASUREMENT_START,
NL80211_CMD_PEER_MEASUREMENT_RESULT,
NL80211_CMD_PEER_MEASUREMENT_COMPLETE,
NL80211_CMD_NOTIFY_RADAR,
NL80211_CMD_UPDATE_OWE_INFO,
NL80211_CMD_PROBE_MESH_LINK,
NL80211_CMD_SET_TID_CONFIG,
NL80211_CMD_UNPROT_BEACON,
NL80211_CMD_CONTROL_PORT_FRAME_TX_STATUS,
NL80211_CMD_SET_SAR_SPECS,
NL80211_CMD_OBSS_COLOR_COLLISION,
NL80211_CMD_COLOR_CHANGE_REQUEST,
NL80211_CMD_COLOR_CHANGE_STARTED,
NL80211_CMD_COLOR_CHANGE_ABORTED,
NL80211_CMD_COLOR_CHANGE_COMPLETED,
NL80211_CMD_SET_FILS_AAD,
NL80211_CMD_ASSOC_COMEBACK,
NL80211_CMD_ADD_LINK,
NL80211_CMD_REMOVE_LINK,
NL80211_CMD_ADD_LINK_STA,
NL80211_CMD_MODIFY_LINK_STA,
NL80211_CMD_REMOVE_LINK_STA,
NL80211_CMD_SET_HW_TIMESTAMP,
/* add new commands above here */
/* used to define NL80211_CMD_MAX below */
__NL80211_CMD_AFTER_LAST,
NL80211_CMD_MAX = __NL80211_CMD_AFTER_LAST - 1
};
/*
* Allow user space programs to use #ifdef on new commands by defining them
* here
*/
#define NL80211_CMD_SET_BSS NL80211_CMD_SET_BSS
#define NL80211_CMD_SET_MGMT_EXTRA_IE NL80211_CMD_SET_MGMT_EXTRA_IE
#define NL80211_CMD_REG_CHANGE NL80211_CMD_REG_CHANGE
#define NL80211_CMD_AUTHENTICATE NL80211_CMD_AUTHENTICATE
#define NL80211_CMD_ASSOCIATE NL80211_CMD_ASSOCIATE
#define NL80211_CMD_DEAUTHENTICATE NL80211_CMD_DEAUTHENTICATE
#define NL80211_CMD_DISASSOCIATE NL80211_CMD_DISASSOCIATE
#define NL80211_CMD_REG_BEACON_HINT NL80211_CMD_REG_BEACON_HINT
#define NL80211_ATTR_FEATURE_FLAGS NL80211_ATTR_FEATURE_FLAGS
/* source-level API compatibility */
#define NL80211_CMD_GET_MESH_PARAMS NL80211_CMD_GET_MESH_CONFIG
#define NL80211_CMD_SET_MESH_PARAMS NL80211_CMD_SET_MESH_CONFIG
#define NL80211_MESH_SETUP_VENDOR_PATH_SEL_IE NL80211_MESH_SETUP_IE
/**
* enum nl80211_attrs - nl80211 netlink attributes
*
* @NL80211_ATTR_UNSPEC: unspecified attribute to catch errors
*
* @NL80211_ATTR_WIPHY: index of wiphy to operate on, cf.
* /sys/class/ieee80211/<phyname>/index
* @NL80211_ATTR_WIPHY_NAME: wiphy name (used for renaming)
* @NL80211_ATTR_WIPHY_TXQ_PARAMS: a nested array of TX queue parameters
* @NL80211_ATTR_WIPHY_FREQ: frequency of the selected channel in MHz,
* defines the channel together with the (deprecated)
* %NL80211_ATTR_WIPHY_CHANNEL_TYPE attribute or the attributes
* %NL80211_ATTR_CHANNEL_WIDTH and if needed %NL80211_ATTR_CENTER_FREQ1
* and %NL80211_ATTR_CENTER_FREQ2
* @NL80211_ATTR_CHANNEL_WIDTH: u32 attribute containing one of the values
* of &enum nl80211_chan_width, describing the channel width. See the
* documentation of the enum for more information.
* @NL80211_ATTR_CENTER_FREQ1: Center frequency of the first part of the
* channel, used for anything but 20 MHz bandwidth. In S1G this is the
* operating channel center frequency.
* @NL80211_ATTR_CENTER_FREQ2: Center frequency of the second part of the
* channel, used only for 80+80 MHz bandwidth
* @NL80211_ATTR_WIPHY_CHANNEL_TYPE: included with NL80211_ATTR_WIPHY_FREQ
* if HT20 or HT40 are to be used (i.e., HT disabled if not included):
* NL80211_CHAN_NO_HT = HT not allowed (i.e., same as not including
* this attribute)
* NL80211_CHAN_HT20 = HT20 only
* NL80211_CHAN_HT40MINUS = secondary channel is below the primary channel
* NL80211_CHAN_HT40PLUS = secondary channel is above the primary channel
* This attribute is now deprecated.
* @NL80211_ATTR_WIPHY_RETRY_SHORT: TX retry limit for frames whose length is
* less than or equal to the RTS threshold; allowed range: 1..255;
* dot11ShortRetryLimit; u8
* @NL80211_ATTR_WIPHY_RETRY_LONG: TX retry limit for frames whose length is
* greater than the RTS threshold; allowed range: 1..255;
* dot11ShortLongLimit; u8
* @NL80211_ATTR_WIPHY_FRAG_THRESHOLD: fragmentation threshold, i.e., maximum
* length in octets for frames; allowed range: 256..8000, disable
* fragmentation with (u32)-1; dot11FragmentationThreshold; u32
* @NL80211_ATTR_WIPHY_RTS_THRESHOLD: RTS threshold (TX frames with length
* larger than or equal to this use RTS/CTS handshake); allowed range:
* 0..65536, disable with (u32)-1; dot11RTSThreshold; u32
* @NL80211_ATTR_WIPHY_COVERAGE_CLASS: Coverage Class as defined by IEEE 802.11
* section 7.3.2.9; dot11CoverageClass; u8
*
* @NL80211_ATTR_IFINDEX: network interface index of the device to operate on
* @NL80211_ATTR_IFNAME: network interface name
* @NL80211_ATTR_IFTYPE: type of virtual interface, see &enum nl80211_iftype
*
* @NL80211_ATTR_WDEV: wireless device identifier, used for pseudo-devices
* that don't have a netdev (u64)
*
* @NL80211_ATTR_MAC: MAC address (various uses)
*
* @NL80211_ATTR_KEY_DATA: (temporal) key data; for TKIP this consists of
* 16 bytes encryption key followed by 8 bytes each for TX and RX MIC
* keys
* @NL80211_ATTR_KEY_IDX: key ID (u8, 0-3)
* @NL80211_ATTR_KEY_CIPHER: key cipher suite (u32, as defined by IEEE 802.11
* section 7.3.2.25.1, e.g. 0x000FAC04)
* @NL80211_ATTR_KEY_SEQ: transmit key sequence number (IV/PN) for TKIP and
* CCMP keys, each six bytes in little endian
* @NL80211_ATTR_KEY_DEFAULT: Flag attribute indicating the key is default key
* @NL80211_ATTR_KEY_DEFAULT_MGMT: Flag attribute indicating the key is the
* default management key
* @NL80211_ATTR_CIPHER_SUITES_PAIRWISE: For crypto settings for connect or
* other commands, indicates which pairwise cipher suites are used
* @NL80211_ATTR_CIPHER_SUITE_GROUP: For crypto settings for connect or
* other commands, indicates which group cipher suite is used
*
* @NL80211_ATTR_BEACON_INTERVAL: beacon interval in TU
* @NL80211_ATTR_DTIM_PERIOD: DTIM period for beaconing
* @NL80211_ATTR_BEACON_HEAD: portion of the beacon before the TIM IE
* @NL80211_ATTR_BEACON_TAIL: portion of the beacon after the TIM IE
*
* @NL80211_ATTR_STA_AID: Association ID for the station (u16)
* @NL80211_ATTR_STA_FLAGS: flags, nested element with NLA_FLAG attributes of
* &enum nl80211_sta_flags (deprecated, use %NL80211_ATTR_STA_FLAGS2)
* @NL80211_ATTR_STA_LISTEN_INTERVAL: listen interval as defined by
* IEEE 802.11 7.3.1.6 (u16).
* @NL80211_ATTR_STA_SUPPORTED_RATES: supported rates, array of supported
* rates as defined by IEEE 802.11 7.3.2.2 but without the length
* restriction (at most %NL80211_MAX_SUPP_RATES).
* @NL80211_ATTR_STA_VLAN: interface index of VLAN interface to move station
* to, or the AP interface the station was originally added to.
* @NL80211_ATTR_STA_INFO: information about a station, part of station info
* given for %NL80211_CMD_GET_STATION, nested attribute containing
* info as possible, see &enum nl80211_sta_info.
*
* @NL80211_ATTR_WIPHY_BANDS: Information about an operating bands,
* consisting of a nested array.
*
* @NL80211_ATTR_MESH_ID: mesh id (1-32 bytes).
* @NL80211_ATTR_STA_PLINK_ACTION: action to perform on the mesh peer link
* (see &enum nl80211_plink_action).
* @NL80211_ATTR_MPATH_NEXT_HOP: MAC address of the next hop for a mesh path.
* @NL80211_ATTR_MPATH_INFO: information about a mesh_path, part of mesh path
* info given for %NL80211_CMD_GET_MPATH, nested attribute described at
* &enum nl80211_mpath_info.
*
* @NL80211_ATTR_MNTR_FLAGS: flags, nested element with NLA_FLAG attributes of
* &enum nl80211_mntr_flags.
*
* @NL80211_ATTR_REG_ALPHA2: an ISO-3166-alpha2 country code for which the
* current regulatory domain should be set to or is already set to.
* For example, 'CR', for Costa Rica. This attribute is used by the kernel
* to query the CRDA to retrieve one regulatory domain. This attribute can
* also be used by userspace to query the kernel for the currently set
* regulatory domain. We chose an alpha2 as that is also used by the
* IEEE-802.11 country information element to identify a country.
* Users can also simply ask the wireless core to set regulatory domain
* to a specific alpha2.
* @NL80211_ATTR_REG_RULES: a nested array of regulatory domain regulatory
* rules.
*
* @NL80211_ATTR_BSS_CTS_PROT: whether CTS protection is enabled (u8, 0 or 1)
* @NL80211_ATTR_BSS_SHORT_PREAMBLE: whether short preamble is enabled
* (u8, 0 or 1)
* @NL80211_ATTR_BSS_SHORT_SLOT_TIME: whether short slot time enabled
* (u8, 0 or 1)
* @NL80211_ATTR_BSS_BASIC_RATES: basic rates, array of basic
* rates in format defined by IEEE 802.11 7.3.2.2 but without the length
* restriction (at most %NL80211_MAX_SUPP_RATES).
*
* @NL80211_ATTR_HT_CAPABILITY: HT Capability information element (from
* association request when used with NL80211_CMD_NEW_STATION)
*
* @NL80211_ATTR_SUPPORTED_IFTYPES: nested attribute containing all
* supported interface types, each a flag attribute with the number
* of the interface mode.
*
* @NL80211_ATTR_MGMT_SUBTYPE: Management frame subtype for
* %NL80211_CMD_SET_MGMT_EXTRA_IE.
*
* @NL80211_ATTR_IE: Information element(s) data (used, e.g., with
* %NL80211_CMD_SET_MGMT_EXTRA_IE).
*
* @NL80211_ATTR_MAX_NUM_SCAN_SSIDS: number of SSIDs you can scan with
* a single scan request, a wiphy attribute.
* @NL80211_ATTR_MAX_NUM_SCHED_SCAN_SSIDS: number of SSIDs you can
* scan with a single scheduled scan request, a wiphy attribute.
* @NL80211_ATTR_MAX_SCAN_IE_LEN: maximum length of information elements
* that can be added to a scan request
* @NL80211_ATTR_MAX_SCHED_SCAN_IE_LEN: maximum length of information
* elements that can be added to a scheduled scan request
* @NL80211_ATTR_MAX_MATCH_SETS: maximum number of sets that can be
* used with @NL80211_ATTR_SCHED_SCAN_MATCH, a wiphy attribute.
*
* @NL80211_ATTR_SCAN_FREQUENCIES: nested attribute with frequencies (in MHz)
* @NL80211_ATTR_SCAN_SSIDS: nested attribute with SSIDs, leave out for passive
* scanning and include a zero-length SSID (wildcard) for wildcard scan
* @NL80211_ATTR_BSS: scan result BSS
*
* @NL80211_ATTR_REG_INITIATOR: indicates who requested the regulatory domain
* currently in effect. This could be any of the %NL80211_REGDOM_SET_BY_*
* @NL80211_ATTR_REG_TYPE: indicates the type of the regulatory domain currently
* set. This can be one of the nl80211_reg_type (%NL80211_REGDOM_TYPE_*)
*
* @NL80211_ATTR_SUPPORTED_COMMANDS: wiphy attribute that specifies
* an array of command numbers (i.e. a mapping index to command number)
* that the driver for the given wiphy supports.
*
* @NL80211_ATTR_FRAME: frame data (binary attribute), including frame header
* and body, but not FCS; used, e.g., with NL80211_CMD_AUTHENTICATE and
* NL80211_CMD_ASSOCIATE events
* @NL80211_ATTR_SSID: SSID (binary attribute, 0..32 octets)
* @NL80211_ATTR_AUTH_TYPE: AuthenticationType, see &enum nl80211_auth_type,
* represented as a u32
* @NL80211_ATTR_REASON_CODE: ReasonCode for %NL80211_CMD_DEAUTHENTICATE and
* %NL80211_CMD_DISASSOCIATE, u16
*
* @NL80211_ATTR_KEY_TYPE: Key Type, see &enum nl80211_key_type, represented as
* a u32
*
* @NL80211_ATTR_FREQ_BEFORE: A channel which has suffered a regulatory change
* due to considerations from a beacon hint. This attribute reflects
* the state of the channel _before_ the beacon hint processing. This
* attributes consists of a nested attribute containing
* NL80211_FREQUENCY_ATTR_*
* @NL80211_ATTR_FREQ_AFTER: A channel which has suffered a regulatory change
* due to considerations from a beacon hint. This attribute reflects
* the state of the channel _after_ the beacon hint processing. This
* attributes consists of a nested attribute containing
* NL80211_FREQUENCY_ATTR_*
*
* @NL80211_ATTR_CIPHER_SUITES: a set of u32 values indicating the supported
* cipher suites
*
* @NL80211_ATTR_FREQ_FIXED: a flag indicating the IBSS should not try to look
* for other networks on different channels
*
* @NL80211_ATTR_TIMED_OUT: a flag indicating than an operation timed out; this
* is used, e.g., with %NL80211_CMD_AUTHENTICATE event
*
* @NL80211_ATTR_USE_MFP: Whether management frame protection (IEEE 802.11w) is
* used for the association (&enum nl80211_mfp, represented as a u32);
* this attribute can be used with %NL80211_CMD_ASSOCIATE and
* %NL80211_CMD_CONNECT requests. %NL80211_MFP_OPTIONAL is not allowed for
* %NL80211_CMD_ASSOCIATE since user space SME is expected and hence, it
* must have decided whether to use management frame protection or not.
* Setting %NL80211_MFP_OPTIONAL with a %NL80211_CMD_CONNECT request will
* let the driver (or the firmware) decide whether to use MFP or not.
*
* @NL80211_ATTR_STA_FLAGS2: Attribute containing a
* &struct nl80211_sta_flag_update.
*
* @NL80211_ATTR_CONTROL_PORT: A flag indicating whether user space controls
* IEEE 802.1X port, i.e., sets/clears %NL80211_STA_FLAG_AUTHORIZED, in
* station mode. If the flag is included in %NL80211_CMD_ASSOCIATE
* request, the driver will assume that the port is unauthorized until
* authorized by user space. Otherwise, port is marked authorized by
* default in station mode.
* @NL80211_ATTR_CONTROL_PORT_ETHERTYPE: A 16-bit value indicating the
* ethertype that will be used for key negotiation. It can be
* specified with the associate and connect commands. If it is not
* specified, the value defaults to 0x888E (PAE, 802.1X). This
* attribute is also used as a flag in the wiphy information to
* indicate that protocols other than PAE are supported.
* @NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT: When included along with
* %NL80211_ATTR_CONTROL_PORT_ETHERTYPE, indicates that the custom
* ethertype frames used for key negotiation must not be encrypted.
* @NL80211_ATTR_CONTROL_PORT_OVER_NL80211: A flag indicating whether control
* port frames (e.g. of type given in %NL80211_ATTR_CONTROL_PORT_ETHERTYPE)
* will be sent directly to the network interface or sent via the NL80211
* socket. If this attribute is missing, then legacy behavior of sending
* control port frames directly to the network interface is used. If the
* flag is included, then control port frames are sent over NL80211 instead
* using %CMD_CONTROL_PORT_FRAME. If control port routing over NL80211 is
* to be used then userspace must also use the %NL80211_ATTR_SOCKET_OWNER
* flag. When used with %NL80211_ATTR_CONTROL_PORT_NO_PREAUTH, pre-auth
* frames are not forwared over the control port.
*
* @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver.
* We recommend using nested, driver-specific attributes within this.
*
* @NL80211_ATTR_DISCONNECTED_BY_AP: A flag indicating that the DISCONNECT
* event was due to the AP disconnecting the station, and not due to
* a local disconnect request.
* @NL80211_ATTR_STATUS_CODE: StatusCode for the %NL80211_CMD_CONNECT
* event (u16)
* @NL80211_ATTR_PRIVACY: Flag attribute, used with connect(), indicating
* that protected APs should be used. This is also used with NEW_BEACON to
* indicate that the BSS is to use protection.
*
* @NL80211_ATTR_CIPHERS_PAIRWISE: Used with CONNECT, ASSOCIATE, and NEW_BEACON
* to indicate which unicast key ciphers will be used with the connection
* (an array of u32).
* @NL80211_ATTR_CIPHER_GROUP: Used with CONNECT, ASSOCIATE, and NEW_BEACON to
* indicate which group key cipher will be used with the connection (a
* u32).
* @NL80211_ATTR_WPA_VERSIONS: Used with CONNECT, ASSOCIATE, and NEW_BEACON to
* indicate which WPA version(s) the AP we want to associate with is using
* (a u32 with flags from &enum nl80211_wpa_versions).
* @NL80211_ATTR_AKM_SUITES: Used with CONNECT, ASSOCIATE, and NEW_BEACON to
* indicate which key management algorithm(s) to use (an array of u32).
* This attribute is also sent in response to @NL80211_CMD_GET_WIPHY,
* indicating the supported AKM suites, intended for specific drivers which
* implement SME and have constraints on which AKMs are supported and also
* the cases where an AKM support is offloaded to the driver/firmware.
* If there is no such notification from the driver, user space should
* assume the driver supports all the AKM suites.
*
* @NL80211_ATTR_REQ_IE: (Re)association request information elements as
* sent out by the card, for ROAM and successful CONNECT events.
* @NL80211_ATTR_RESP_IE: (Re)association response information elements as
* sent by peer, for ROAM and successful CONNECT events.
*
* @NL80211_ATTR_PREV_BSSID: previous BSSID, to be used in ASSOCIATE and CONNECT
* commands to specify a request to reassociate within an ESS, i.e., to use
* Reassociate Request frame (with the value of this attribute in the
* Current AP address field) instead of Association Request frame which is
* used for the initial association to an ESS.
*
* @NL80211_ATTR_KEY: key information in a nested attribute with
* %NL80211_KEY_* sub-attributes
* @NL80211_ATTR_KEYS: array of keys for static WEP keys for connect()
* and join_ibss(), key information is in a nested attribute each
* with %NL80211_KEY_* sub-attributes
*
* @NL80211_ATTR_PID: Process ID of a network namespace.
*
* @NL80211_ATTR_GENERATION: Used to indicate consistent snapshots for
* dumps. This number increases whenever the object list being
* dumped changes, and as such userspace can verify that it has
* obtained a complete and consistent snapshot by verifying that
* all dump messages contain the same generation number. If it
* changed then the list changed and the dump should be repeated
* completely from scratch.
*
* @NL80211_ATTR_4ADDR: Use 4-address frames on a virtual interface
*
* @NL80211_ATTR_SURVEY_INFO: survey information about a channel, part of
* the survey response for %NL80211_CMD_GET_SURVEY, nested attribute
* containing info as possible, see &enum survey_info.
*
* @NL80211_ATTR_PMKID: PMK material for PMKSA caching.
* @NL80211_ATTR_MAX_NUM_PMKIDS: maximum number of PMKIDs a firmware can
* cache, a wiphy attribute.
*
* @NL80211_ATTR_DURATION: Duration of an operation in milliseconds, u32.
* @NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION: Device attribute that
* specifies the maximum duration that can be requested with the
* remain-on-channel operation, in milliseconds, u32.
*
* @NL80211_ATTR_COOKIE: Generic 64-bit cookie to identify objects.
*
* @NL80211_ATTR_TX_RATES: Nested set of attributes
* (enum nl80211_tx_rate_attributes) describing TX rates per band. The
* enum nl80211_band value is used as the index (nla_type() of the nested
* data. If a band is not included, it will be configured to allow all
* rates based on negotiated supported rates information. This attribute
* is used with %NL80211_CMD_SET_TX_BITRATE_MASK and with starting AP,
* and joining mesh networks (not IBSS yet). In the later case, it must
* specify just a single bitrate, which is to be used for the beacon.
* The driver must also specify support for this with the extended
* features NL80211_EXT_FEATURE_BEACON_RATE_LEGACY,
* NL80211_EXT_FEATURE_BEACON_RATE_HT,
* NL80211_EXT_FEATURE_BEACON_RATE_VHT and
* NL80211_EXT_FEATURE_BEACON_RATE_HE.
*
* @NL80211_ATTR_FRAME_MATCH: A binary attribute which typically must contain
* at least one byte, currently used with @NL80211_CMD_REGISTER_FRAME.
* @NL80211_ATTR_FRAME_TYPE: A u16 indicating the frame type/subtype for the
* @NL80211_CMD_REGISTER_FRAME command.
* @NL80211_ATTR_TX_FRAME_TYPES: wiphy capability attribute, which is a
* nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing
* information about which frame types can be transmitted with
* %NL80211_CMD_FRAME.
* @NL80211_ATTR_RX_FRAME_TYPES: wiphy capability attribute, which is a
* nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing
* information about which frame types can be registered for RX.
*
* @NL80211_ATTR_ACK: Flag attribute indicating that the frame was
* acknowledged by the recipient.
*
* @NL80211_ATTR_PS_STATE: powersave state, using &enum nl80211_ps_state values.
*
* @NL80211_ATTR_CQM: connection quality monitor configuration in a
* nested attribute with %NL80211_ATTR_CQM_* sub-attributes.
*
* @NL80211_ATTR_LOCAL_STATE_CHANGE: Flag attribute to indicate that a command
* is requesting a local authentication/association state change without
* invoking actual management frame exchange. This can be used with
* NL80211_CMD_AUTHENTICATE, NL80211_CMD_DEAUTHENTICATE,
* NL80211_CMD_DISASSOCIATE.
*
* @NL80211_ATTR_AP_ISOLATE: (AP mode) Do not forward traffic between stations
* connected to this BSS.
*
* @NL80211_ATTR_WIPHY_TX_POWER_SETTING: Transmit power setting type. See
* &enum nl80211_tx_power_setting for possible values.
* @NL80211_ATTR_WIPHY_TX_POWER_LEVEL: Transmit power level in signed mBm units.
* This is used in association with @NL80211_ATTR_WIPHY_TX_POWER_SETTING
* for non-automatic settings.
*
* @NL80211_ATTR_SUPPORT_IBSS_RSN: The device supports IBSS RSN, which mostly
* means support for per-station GTKs.
*
* @NL80211_ATTR_WIPHY_ANTENNA_TX: Bitmap of allowed antennas for transmitting.
* This can be used to mask out antennas which are not attached or should
* not be used for transmitting. If an antenna is not selected in this
* bitmap the hardware is not allowed to transmit on this antenna.
*
* Each bit represents one antenna, starting with antenna 1 at the first
* bit. Depending on which antennas are selected in the bitmap, 802.11n
* drivers can derive which chainmasks to use (if all antennas belonging to
* a particular chain are disabled this chain should be disabled) and if
* a chain has diversity antennas wether diversity should be used or not.
* HT capabilities (STBC, TX Beamforming, Antenna selection) can be
* derived from the available chains after applying the antenna mask.
* Non-802.11n drivers can derive wether to use diversity or not.
* Drivers may reject configurations or RX/TX mask combinations they cannot
* support by returning -EINVAL.
*
* @NL80211_ATTR_WIPHY_ANTENNA_RX: Bitmap of allowed antennas for receiving.
* This can be used to mask out antennas which are not attached or should
* not be used for receiving. If an antenna is not selected in this bitmap
* the hardware should not be configured to receive on this antenna.
* For a more detailed description see @NL80211_ATTR_WIPHY_ANTENNA_TX.
*
* @NL80211_ATTR_WIPHY_ANTENNA_AVAIL_TX: Bitmap of antennas which are available
* for configuration as TX antennas via the above parameters.
*
* @NL80211_ATTR_WIPHY_ANTENNA_AVAIL_RX: Bitmap of antennas which are available
* for configuration as RX antennas via the above parameters.
*
* @NL80211_ATTR_MCAST_RATE: Multicast tx rate (in 100 kbps) for IBSS
*
* @NL80211_ATTR_OFFCHANNEL_TX_OK: For management frame TX, the frame may be
* transmitted on another channel when the channel given doesn't match
* the current channel. If the current channel doesn't match and this
* flag isn't set, the frame will be rejected. This is also used as an
* nl80211 capability flag.
*
* @NL80211_ATTR_BSS_HT_OPMODE: HT operation mode (u16)
*
* @NL80211_ATTR_KEY_DEFAULT_TYPES: A nested attribute containing flags
* attributes, specifying what a key should be set as default as.
* See &enum nl80211_key_default_types.
*
* @NL80211_ATTR_MESH_SETUP: Optional mesh setup parameters. These cannot be
* changed once the mesh is active.
* @NL80211_ATTR_MESH_CONFIG: Mesh configuration parameters, a nested attribute
* containing attributes from &enum nl80211_meshconf_params.
* @NL80211_ATTR_SUPPORT_MESH_AUTH: Currently, this means the underlying driver
* allows auth frames in a mesh to be passed to userspace for processing via
* the @NL80211_MESH_SETUP_USERSPACE_AUTH flag.
* @NL80211_ATTR_STA_PLINK_STATE: The state of a mesh peer link as defined in
* &enum nl80211_plink_state. Used when userspace is driving the peer link
* management state machine. @NL80211_MESH_SETUP_USERSPACE_AMPE or
* @NL80211_MESH_SETUP_USERSPACE_MPM must be enabled.
*
* @NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED: indicates, as part of the wiphy
* capabilities, the supported WoWLAN triggers
* @NL80211_ATTR_WOWLAN_TRIGGERS: used by %NL80211_CMD_SET_WOWLAN to
* indicate which WoW triggers should be enabled. This is also
* used by %NL80211_CMD_GET_WOWLAN to get the currently enabled WoWLAN
* triggers.
*
* @NL80211_ATTR_SCHED_SCAN_INTERVAL: Interval between scheduled scan
* cycles, in msecs.
*
* @NL80211_ATTR_SCHED_SCAN_MATCH: Nested attribute with one or more
* sets of attributes to match during scheduled scans. Only BSSs
* that match any of the sets will be reported. These are
* pass-thru filter rules.
* For a match to succeed, the BSS must match all attributes of a
* set. Since not every hardware supports matching all types of
* attributes, there is no guarantee that the reported BSSs are
* fully complying with the match sets and userspace needs to be
* able to ignore them by itself.
* Thus, the implementation is somewhat hardware-dependent, but
* this is only an optimization and the userspace application
* needs to handle all the non-filtered results anyway.
* If the match attributes don't make sense when combined with
* the values passed in @NL80211_ATTR_SCAN_SSIDS (eg. if an SSID
* is included in the probe request, but the match attributes
* will never let it go through), -EINVAL may be returned.
* If omitted, no filtering is done.
*
* @NL80211_ATTR_INTERFACE_COMBINATIONS: Nested attribute listing the supported
* interface combinations. In each nested item, it contains attributes
* defined in &enum nl80211_if_combination_attrs.
* @NL80211_ATTR_SOFTWARE_IFTYPES: Nested attribute (just like
* %NL80211_ATTR_SUPPORTED_IFTYPES) containing the interface types that
* are managed in software: interfaces of these types aren't subject to
* any restrictions in their number or combinations.
*
* @NL80211_ATTR_REKEY_DATA: nested attribute containing the information
* necessary for GTK rekeying in the device, see &enum nl80211_rekey_data.
*
* @NL80211_ATTR_SCAN_SUPP_RATES: rates per to be advertised as supported in scan,
* nested array attribute containing an entry for each band, with the entry
* being a list of supported rates as defined by IEEE 802.11 7.3.2.2 but
* without the length restriction (at most %NL80211_MAX_SUPP_RATES).
*
* @NL80211_ATTR_HIDDEN_SSID: indicates whether SSID is to be hidden from Beacon
* and Probe Response (when response to wildcard Probe Request); see
* &enum nl80211_hidden_ssid, represented as a u32
*
* @NL80211_ATTR_IE_PROBE_RESP: Information element(s) for Probe Response frame.
* This is used with %NL80211_CMD_NEW_BEACON and %NL80211_CMD_SET_BEACON to
* provide extra IEs (e.g., WPS/P2P IE) into Probe Response frames when the
* driver (or firmware) replies to Probe Request frames.
* @NL80211_ATTR_IE_ASSOC_RESP: Information element(s) for (Re)Association
* Response frames. This is used with %NL80211_CMD_NEW_BEACON and
* %NL80211_CMD_SET_BEACON to provide extra IEs (e.g., WPS/P2P IE) into
* (Re)Association Response frames when the driver (or firmware) replies to
* (Re)Association Request frames.
*
* @NL80211_ATTR_STA_WME: Nested attribute containing the wme configuration
* of the station, see &enum nl80211_sta_wme_attr.
* @NL80211_ATTR_SUPPORT_AP_UAPSD: the device supports uapsd when working
* as AP.
*
* @NL80211_ATTR_ROAM_SUPPORT: Indicates whether the firmware is capable of
* roaming to another AP in the same ESS if the signal lever is low.
*
* @NL80211_ATTR_PMKSA_CANDIDATE: Nested attribute containing the PMKSA caching
* candidate information, see &enum nl80211_pmksa_candidate_attr.
*
* @NL80211_ATTR_TX_NO_CCK_RATE: Indicates whether to use CCK rate or not
* for management frames transmission. In order to avoid p2p probe/action
* frames are being transmitted at CCK rate in 2GHz band, the user space
* applications use this attribute.
* This attribute is used with %NL80211_CMD_TRIGGER_SCAN and
* %NL80211_CMD_FRAME commands.
*
* @NL80211_ATTR_TDLS_ACTION: Low level TDLS action code (e.g. link setup
* request, link setup confirm, link teardown, etc.). Values are
* described in the TDLS (802.11z) specification.
* @NL80211_ATTR_TDLS_DIALOG_TOKEN: Non-zero token for uniquely identifying a
* TDLS conversation between two devices.
* @NL80211_ATTR_TDLS_OPERATION: High level TDLS operation; see
* &enum nl80211_tdls_operation, represented as a u8.
* @NL80211_ATTR_TDLS_SUPPORT: A flag indicating the device can operate
* as a TDLS peer sta.
* @NL80211_ATTR_TDLS_EXTERNAL_SETUP: The TDLS discovery/setup and teardown
* procedures should be performed by sending TDLS packets via
* %NL80211_CMD_TDLS_MGMT. Otherwise %NL80211_CMD_TDLS_OPER should be
* used for asking the driver to perform a TDLS operation.
*
* @NL80211_ATTR_DEVICE_AP_SME: This u32 attribute may be listed for devices
* that have AP support to indicate that they have the AP SME integrated
* with support for the features listed in this attribute, see
* &enum nl80211_ap_sme_features.
*
* @NL80211_ATTR_DONT_WAIT_FOR_ACK: Used with %NL80211_CMD_FRAME, this tells
* the driver to not wait for an acknowledgement. Note that due to this,
* it will also not give a status callback nor return a cookie. This is
* mostly useful for probe responses to save airtime.
*
* @NL80211_ATTR_FEATURE_FLAGS: This u32 attribute contains flags from
* &enum nl80211_feature_flags and is advertised in wiphy information.
* @NL80211_ATTR_PROBE_RESP_OFFLOAD: Indicates that the HW responds to probe
* requests while operating in AP-mode.
* This attribute holds a bitmap of the supported protocols for
* offloading (see &enum nl80211_probe_resp_offload_support_attr).
*
* @NL80211_ATTR_PROBE_RESP: Probe Response template data. Contains the entire
* probe-response frame. The DA field in the 802.11 header is zero-ed out,
* to be filled by the FW.
* @NL80211_ATTR_DISABLE_HT: Force HT capable interfaces to disable
* this feature during association. This is a flag attribute.
* Currently only supported in mac80211 drivers.
* @NL80211_ATTR_DISABLE_VHT: Force VHT capable interfaces to disable
* this feature during association. This is a flag attribute.
* Currently only supported in mac80211 drivers.
* @NL80211_ATTR_DISABLE_HE: Force HE capable interfaces to disable
* this feature during association. This is a flag attribute.
* Currently only supported in mac80211 drivers.
* @NL80211_ATTR_HT_CAPABILITY_MASK: Specify which bits of the
* ATTR_HT_CAPABILITY to which attention should be paid.
* Currently, only mac80211 NICs support this feature.
* The values that may be configured are:
* MCS rates, MAX-AMSDU, HT-20-40 and HT_CAP_SGI_40
* AMPDU density and AMPDU factor.
* All values are treated as suggestions and may be ignored
* by the driver as required. The actual values may be seen in
* the station debugfs ht_caps file.
*
* @NL80211_ATTR_DFS_REGION: region for regulatory rules which this country
* abides to when initiating radiation on DFS channels. A country maps
* to one DFS region.
*
* @NL80211_ATTR_NOACK_MAP: This u16 bitmap contains the No Ack Policy of
* up to 16 TIDs.
*
* @NL80211_ATTR_INACTIVITY_TIMEOUT: timeout value in seconds, this can be
* used by the drivers which has MLME in firmware and does not have support
* to report per station tx/rx activity to free up the station entry from
* the list. This needs to be used when the driver advertises the
* capability to timeout the stations.
*
* @NL80211_ATTR_RX_SIGNAL_DBM: signal strength in dBm (as a 32-bit int);
* this attribute is (depending on the driver capabilities) added to
* received frames indicated with %NL80211_CMD_FRAME.
*
* @NL80211_ATTR_BG_SCAN_PERIOD: Background scan period in seconds
* or 0 to disable background scan.
*
* @NL80211_ATTR_USER_REG_HINT_TYPE: type of regulatory hint passed from
* userspace. If unset it is assumed the hint comes directly from
* a user. If set code could specify exactly what type of source
* was used to provide the hint. For the different types of
* allowed user regulatory hints see nl80211_user_reg_hint_type.
*
* @NL80211_ATTR_CONN_FAILED_REASON: The reason for which AP has rejected
* the connection request from a station. nl80211_connect_failed_reason
* enum has different reasons of connection failure.
*
* @NL80211_ATTR_AUTH_DATA: Fields and elements in Authentication frames.
* This contains the authentication frame body (non-IE and IE data),
* excluding the Authentication algorithm number, i.e., starting at the
* Authentication transaction sequence number field. It is used with
* authentication algorithms that need special fields to be added into
* the frames (SAE and FILS). Currently, only the SAE cases use the
* initial two fields (Authentication transaction sequence number and
* Status code). However, those fields are included in the attribute data
* for all authentication algorithms to keep the attribute definition
* consistent.
*
* @NL80211_ATTR_VHT_CAPABILITY: VHT Capability information element (from
* association request when used with NL80211_CMD_NEW_STATION)
*
* @NL80211_ATTR_SCAN_FLAGS: scan request control flags (u32)
*
* @NL80211_ATTR_P2P_CTWINDOW: P2P GO Client Traffic Window (u8), used with
* the START_AP and SET_BSS commands
* @NL80211_ATTR_P2P_OPPPS: P2P GO opportunistic PS (u8), used with the
* START_AP and SET_BSS commands. This can have the values 0 or 1;
* if not given in START_AP 0 is assumed, if not given in SET_BSS
* no change is made.
*
* @NL80211_ATTR_LOCAL_MESH_POWER_MODE: local mesh STA link-specific power mode
* defined in &enum nl80211_mesh_power_mode.
*
* @NL80211_ATTR_ACL_POLICY: ACL policy, see &enum nl80211_acl_policy,
* carried in a u32 attribute
*
* @NL80211_ATTR_MAC_ADDRS: Array of nested MAC addresses, used for
* MAC ACL.
*
* @NL80211_ATTR_MAC_ACL_MAX: u32 attribute to advertise the maximum
* number of MAC addresses that a device can support for MAC
* ACL.
*
* @NL80211_ATTR_RADAR_EVENT: Type of radar event for notification to userspace,
* contains a value of enum nl80211_radar_event (u32).
*
* @NL80211_ATTR_EXT_CAPA: 802.11 extended capabilities that the kernel driver
* has and handles. The format is the same as the IE contents. See
* 802.11-2012 8.4.2.29 for more information.
* @NL80211_ATTR_EXT_CAPA_MASK: Extended capabilities that the kernel driver
* has set in the %NL80211_ATTR_EXT_CAPA value, for multibit fields.
*
* @NL80211_ATTR_STA_CAPABILITY: Station capabilities (u16) are advertised to
* the driver, e.g., to enable TDLS power save (PU-APSD).
*
* @NL80211_ATTR_STA_EXT_CAPABILITY: Station extended capabilities are
* advertised to the driver, e.g., to enable TDLS off channel operations
* and PU-APSD.
*
* @NL80211_ATTR_PROTOCOL_FEATURES: global nl80211 feature flags, see
* &enum nl80211_protocol_features, the attribute is a u32.
*
* @NL80211_ATTR_SPLIT_WIPHY_DUMP: flag attribute, userspace supports
* receiving the data for a single wiphy split across multiple
* messages, given with wiphy dump message
*
* @NL80211_ATTR_MDID: Mobility Domain Identifier
*
* @NL80211_ATTR_IE_RIC: Resource Information Container Information
* Element
*
* @NL80211_ATTR_CRIT_PROT_ID: critical protocol identifier requiring increased
* reliability, see &enum nl80211_crit_proto_id (u16).
* @NL80211_ATTR_MAX_CRIT_PROT_DURATION: duration in milliseconds in which
* the connection should have increased reliability (u16).
*
* @NL80211_ATTR_PEER_AID: Association ID for the peer TDLS station (u16).
* This is similar to @NL80211_ATTR_STA_AID but with a difference of being
* allowed to be used with the first @NL80211_CMD_SET_STATION command to
* update a TDLS peer STA entry.
*
* @NL80211_ATTR_COALESCE_RULE: Coalesce rule information.
*
* @NL80211_ATTR_CH_SWITCH_COUNT: u32 attribute specifying the number of TBTT's
* until the channel switch event.
* @NL80211_ATTR_CH_SWITCH_BLOCK_TX: flag attribute specifying that transmission
* must be blocked on the current channel (before the channel switch
* operation). Also included in the channel switch started event if quiet
* was requested by the AP.
* @NL80211_ATTR_CSA_IES: Nested set of attributes containing the IE information
* for the time while performing a channel switch.
* @NL80211_ATTR_CNTDWN_OFFS_BEACON: An array of offsets (u16) to the channel
* switch or color change counters in the beacons tail (%NL80211_ATTR_BEACON_TAIL).
* @NL80211_ATTR_CNTDWN_OFFS_PRESP: An array of offsets (u16) to the channel
* switch or color change counters in the probe response (%NL80211_ATTR_PROBE_RESP).
*
* @NL80211_ATTR_RXMGMT_FLAGS: flags for nl80211_send_mgmt(), u32.
* As specified in the &enum nl80211_rxmgmt_flags.
*
* @NL80211_ATTR_STA_SUPPORTED_CHANNELS: array of supported channels.
*
* @NL80211_ATTR_STA_SUPPORTED_OPER_CLASSES: array of supported
* operating classes.
*
* @NL80211_ATTR_HANDLE_DFS: A flag indicating whether user space
* controls DFS operation in IBSS mode. If the flag is included in
* %NL80211_CMD_JOIN_IBSS request, the driver will allow use of DFS
* channels and reports radar events to userspace. Userspace is required
* to react to radar events, e.g. initiate a channel switch or leave the
* IBSS network.
*
* @NL80211_ATTR_SUPPORT_5_MHZ: A flag indicating that the device supports
* 5 MHz channel bandwidth.
* @NL80211_ATTR_SUPPORT_10_MHZ: A flag indicating that the device supports
* 10 MHz channel bandwidth.
*
* @NL80211_ATTR_OPMODE_NOTIF: Operating mode field from Operating Mode
* Notification Element based on association request when used with
* %NL80211_CMD_NEW_STATION or %NL80211_CMD_SET_STATION (only when
* %NL80211_FEATURE_FULL_AP_CLIENT_STATE is supported, or with TDLS);
* u8 attribute.
*
* @NL80211_ATTR_VENDOR_ID: The vendor ID, either a 24-bit OUI or, if
* %NL80211_VENDOR_ID_IS_LINUX is set, a special Linux ID (not used yet)
* @NL80211_ATTR_VENDOR_SUBCMD: vendor sub-command
* @NL80211_ATTR_VENDOR_DATA: data for the vendor command, if any; this
* attribute is also used for vendor command feature advertisement
* @NL80211_ATTR_VENDOR_EVENTS: used for event list advertising in the wiphy
* info, containing a nested array of possible events
*
* @NL80211_ATTR_QOS_MAP: IP DSCP mapping for Interworking QoS mapping. This
* data is in the format defined for the payload of the QoS Map Set element
* in IEEE Std 802.11-2012, 8.4.2.97.
*
* @NL80211_ATTR_MAC_HINT: MAC address recommendation as initial BSS
* @NL80211_ATTR_WIPHY_FREQ_HINT: frequency of the recommended initial BSS
*
* @NL80211_ATTR_MAX_AP_ASSOC_STA: Device attribute that indicates how many
* associated stations are supported in AP mode (including P2P GO); u32.
* Since drivers may not have a fixed limit on the maximum number (e.g.,
* other concurrent operations may affect this), drivers are allowed to
* advertise values that cannot always be met. In such cases, an attempt
* to add a new station entry with @NL80211_CMD_NEW_STATION may fail.
*
* @NL80211_ATTR_CSA_C_OFFSETS_TX: An array of csa counter offsets (u16) which
* should be updated when the frame is transmitted.
* @NL80211_ATTR_MAX_CSA_COUNTERS: U8 attribute used to advertise the maximum
* supported number of csa counters.
*
* @NL80211_ATTR_TDLS_PEER_CAPABILITY: flags for TDLS peer capabilities, u32.
* As specified in the &enum nl80211_tdls_peer_capability.
*
* @NL80211_ATTR_SOCKET_OWNER: Flag attribute, if set during interface
* creation then the new interface will be owned by the netlink socket
* that created it and will be destroyed when the socket is closed.
* If set during scheduled scan start then the new scan req will be
* owned by the netlink socket that created it and the scheduled scan will
* be stopped when the socket is closed.
* If set during configuration of regulatory indoor operation then the
* regulatory indoor configuration would be owned by the netlink socket
* that configured the indoor setting, and the indoor operation would be
* cleared when the socket is closed.
* If set during NAN interface creation, the interface will be destroyed
* if the socket is closed just like any other interface. Moreover, NAN
* notifications will be sent in unicast to that socket. Without this
* attribute, the notifications will be sent to the %NL80211_MCGRP_NAN
* multicast group.
* If set during %NL80211_CMD_ASSOCIATE or %NL80211_CMD_CONNECT the
* station will deauthenticate when the socket is closed.
* If set during %NL80211_CMD_JOIN_IBSS the IBSS will be automatically
* torn down when the socket is closed.
* If set during %NL80211_CMD_JOIN_MESH the mesh setup will be
* automatically torn down when the socket is closed.
* If set during %NL80211_CMD_START_AP the AP will be automatically
* disabled when the socket is closed.
*
* @NL80211_ATTR_TDLS_INITIATOR: flag attribute indicating the current end is
* the TDLS link initiator.
*
* @NL80211_ATTR_USE_RRM: flag for indicating whether the current connection
* shall support Radio Resource Measurements (11k). This attribute can be
* used with %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests.
* User space applications are expected to use this flag only if the
* underlying device supports these minimal RRM features:
* %NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES,
* %NL80211_FEATURE_QUIET,
* Or, if global RRM is supported, see:
* %NL80211_EXT_FEATURE_RRM
* If this flag is used, driver must add the Power Capabilities IE to the
* association request. In addition, it must also set the RRM capability
* flag in the association request's Capability Info field.
*
* @NL80211_ATTR_WIPHY_DYN_ACK: flag attribute used to enable ACK timeout
* estimation algorithm (dynack). In order to activate dynack
* %NL80211_FEATURE_ACKTO_ESTIMATION feature flag must be set by lower
* drivers to indicate dynack capability. Dynack is automatically disabled
* setting valid value for coverage class.
*
* @NL80211_ATTR_TSID: a TSID value (u8 attribute)
* @NL80211_ATTR_USER_PRIO: user priority value (u8 attribute)
* @NL80211_ATTR_ADMITTED_TIME: admitted time in units of 32 microseconds
* (per second) (u16 attribute)
*
* @NL80211_ATTR_SMPS_MODE: SMPS mode to use (ap mode). see
* &enum nl80211_smps_mode.
*
* @NL80211_ATTR_OPER_CLASS: operating class
*
* @NL80211_ATTR_MAC_MASK: MAC address mask
*
* @NL80211_ATTR_WIPHY_SELF_MANAGED_REG: flag attribute indicating this device
* is self-managing its regulatory information and any regulatory domain
* obtained from it is coming from the device's wiphy and not the global
* cfg80211 regdomain.
*
* @NL80211_ATTR_EXT_FEATURES: extended feature flags contained in a byte
* array. The feature flags are identified by their bit index (see &enum
* nl80211_ext_feature_index). The bit index is ordered starting at the
* least-significant bit of the first byte in the array, ie. bit index 0
* is located at bit 0 of byte 0. bit index 25 would be located at bit 1
* of byte 3 (u8 array).
*
* @NL80211_ATTR_SURVEY_RADIO_STATS: Request overall radio statistics to be
* returned along with other survey data. If set, @NL80211_CMD_GET_SURVEY
* may return a survey entry without a channel indicating global radio
* statistics (only some values are valid and make sense.)
* For devices that don't return such an entry even then, the information
* should be contained in the result as the sum of the respective counters
* over all channels.
*
* @NL80211_ATTR_SCHED_SCAN_DELAY: delay before the first cycle of a
* scheduled scan is started. Or the delay before a WoWLAN
* net-detect scan is started, counting from the moment the
* system is suspended. This value is a u32, in seconds.
* @NL80211_ATTR_REG_INDOOR: flag attribute, if set indicates that the device
* is operating in an indoor environment.
*
* @NL80211_ATTR_MAX_NUM_SCHED_SCAN_PLANS: maximum number of scan plans for
* scheduled scan supported by the device (u32), a wiphy attribute.
* @NL80211_ATTR_MAX_SCAN_PLAN_INTERVAL: maximum interval (in seconds) for
* a scan plan (u32), a wiphy attribute.
* @NL80211_ATTR_MAX_SCAN_PLAN_ITERATIONS: maximum number of iterations in
* a scan plan (u32), a wiphy attribute.
* @NL80211_ATTR_SCHED_SCAN_PLANS: a list of scan plans for scheduled scan.
* Each scan plan defines the number of scan iterations and the interval
* between scans. The last scan plan will always run infinitely,
* thus it must not specify the number of iterations, only the interval
* between scans. The scan plans are executed sequentially.
* Each scan plan is a nested attribute of &enum nl80211_sched_scan_plan.
* @NL80211_ATTR_PBSS: flag attribute. If set it means operate
* in a PBSS. Specified in %NL80211_CMD_CONNECT to request
* connecting to a PCP, and in %NL80211_CMD_START_AP to start
* a PCP instead of AP. Relevant for DMG networks only.
* @NL80211_ATTR_BSS_SELECT: nested attribute for driver supporting the
* BSS selection feature. When used with %NL80211_CMD_GET_WIPHY it contains
* attributes according &enum nl80211_bss_select_attr to indicate what
* BSS selection behaviours are supported. When used with %NL80211_CMD_CONNECT
* it contains the behaviour-specific attribute containing the parameters for
* BSS selection to be done by driver and/or firmware.
*
* @NL80211_ATTR_STA_SUPPORT_P2P_PS: whether P2P PS mechanism supported
* or not. u8, one of the values of &enum nl80211_sta_p2p_ps_status
*
* @NL80211_ATTR_PAD: attribute used for padding for 64-bit alignment
*
* @NL80211_ATTR_IFTYPE_EXT_CAPA: Nested attribute of the following attributes:
* %NL80211_ATTR_IFTYPE, %NL80211_ATTR_EXT_CAPA,
* %NL80211_ATTR_EXT_CAPA_MASK, to specify the extended capabilities and
* other interface-type specific capabilities per interface type. For MLO,
* %NL80211_ATTR_EML_CAPABILITY and %NL80211_ATTR_MLD_CAPA_AND_OPS are
* present.
*
* @NL80211_ATTR_MU_MIMO_GROUP_DATA: array of 24 bytes that defines a MU-MIMO
* groupID for monitor mode.
* The first 8 bytes are a mask that defines the membership in each
* group (there are 64 groups, group 0 and 63 are reserved),
* each bit represents a group and set to 1 for being a member in
* that group and 0 for not being a member.
* The remaining 16 bytes define the position in each group: 2 bits for
* each group.
* (smaller group numbers represented on most significant bits and bigger
* group numbers on least significant bits.)
* This attribute is used only if all interfaces are in monitor mode.
* Set this attribute in order to monitor packets using the given MU-MIMO
* groupID data.
* to turn off that feature set all the bits of the groupID to zero.
* @NL80211_ATTR_MU_MIMO_FOLLOW_MAC_ADDR: mac address for the sniffer to follow
* when using MU-MIMO air sniffer.
* to turn that feature off set an invalid mac address
* (e.g. FF:FF:FF:FF:FF:FF)
*
* @NL80211_ATTR_SCAN_START_TIME_TSF: The time at which the scan was actually
* started (u64). The time is the TSF of the BSS the interface that
* requested the scan is connected to (if available, otherwise this
* attribute must not be included).
* @NL80211_ATTR_SCAN_START_TIME_TSF_BSSID: The BSS according to which
* %NL80211_ATTR_SCAN_START_TIME_TSF is set.
* @NL80211_ATTR_MEASUREMENT_DURATION: measurement duration in TUs (u16). If
* %NL80211_ATTR_MEASUREMENT_DURATION_MANDATORY is not set, this is the
* maximum measurement duration allowed. This attribute is used with
* measurement requests. It can also be used with %NL80211_CMD_TRIGGER_SCAN
* if the scan is used for beacon report radio measurement.
* @NL80211_ATTR_MEASUREMENT_DURATION_MANDATORY: flag attribute that indicates
* that the duration specified with %NL80211_ATTR_MEASUREMENT_DURATION is
* mandatory. If this flag is not set, the duration is the maximum duration
* and the actual measurement duration may be shorter.
*
* @NL80211_ATTR_MESH_PEER_AID: Association ID for the mesh peer (u16). This is
* used to pull the stored data for mesh peer in power save state.
*
* @NL80211_ATTR_NAN_MASTER_PREF: the master preference to be used by
* %NL80211_CMD_START_NAN and optionally with
* %NL80211_CMD_CHANGE_NAN_CONFIG. Its type is u8 and it can't be 0.
* Also, values 1 and 255 are reserved for certification purposes and
* should not be used during a normal device operation.
* @NL80211_ATTR_BANDS: operating bands configuration. This is a u32
* bitmask of BIT(NL80211_BAND_*) as described in %enum
* nl80211_band. For instance, for NL80211_BAND_2GHZ, bit 0
* would be set. This attribute is used with
* %NL80211_CMD_START_NAN and %NL80211_CMD_CHANGE_NAN_CONFIG, and
* it is optional. If no bands are set, it means don't-care and
* the device will decide what to use.
* @NL80211_ATTR_NAN_FUNC: a function that can be added to NAN. See
* &enum nl80211_nan_func_attributes for description of this nested
* attribute.
* @NL80211_ATTR_NAN_MATCH: used to report a match. This is a nested attribute.
* See &enum nl80211_nan_match_attributes.
* @NL80211_ATTR_FILS_KEK: KEK for FILS (Re)Association Request/Response frame
* protection.
* @NL80211_ATTR_FILS_NONCES: Nonces (part of AAD) for FILS (Re)Association
* Request/Response frame protection. This attribute contains the 16 octet
* STA Nonce followed by 16 octets of AP Nonce.
*
* @NL80211_ATTR_MULTICAST_TO_UNICAST_ENABLED: Indicates whether or not multicast
* packets should be send out as unicast to all stations (flag attribute).
*
* @NL80211_ATTR_BSSID: The BSSID of the AP. Note that %NL80211_ATTR_MAC is also
* used in various commands/events for specifying the BSSID.
*
* @NL80211_ATTR_SCHED_SCAN_RELATIVE_RSSI: Relative RSSI threshold by which
* other BSSs has to be better or slightly worse than the current
* connected BSS so that they get reported to user space.
* This will give an opportunity to userspace to consider connecting to
* other matching BSSs which have better or slightly worse RSSI than
* the current connected BSS by using an offloaded operation to avoid
* unnecessary wakeups.
*
* @NL80211_ATTR_SCHED_SCAN_RSSI_ADJUST: When present the RSSI level for BSSs in
* the specified band is to be adjusted before doing
* %NL80211_ATTR_SCHED_SCAN_RELATIVE_RSSI based comparison to figure out
* better BSSs. The attribute value is a packed structure
* value as specified by &struct nl80211_bss_select_rssi_adjust.
*
* @NL80211_ATTR_TIMEOUT_REASON: The reason for which an operation timed out.
* u32 attribute with an &enum nl80211_timeout_reason value. This is used,
* e.g., with %NL80211_CMD_CONNECT event.
*
* @NL80211_ATTR_FILS_ERP_USERNAME: EAP Re-authentication Protocol (ERP)
* username part of NAI used to refer keys rRK and rIK. This is used with
* %NL80211_CMD_CONNECT.
*
* @NL80211_ATTR_FILS_ERP_REALM: EAP Re-authentication Protocol (ERP) realm part
* of NAI specifying the domain name of the ER server. This is used with
* %NL80211_CMD_CONNECT.
*
* @NL80211_ATTR_FILS_ERP_NEXT_SEQ_NUM: Unsigned 16-bit ERP next sequence number
* to use in ERP messages. This is used in generating the FILS wrapped data
* for FILS authentication and is used with %NL80211_CMD_CONNECT.
*
* @NL80211_ATTR_FILS_ERP_RRK: ERP re-authentication Root Key (rRK) for the
* NAI specified by %NL80211_ATTR_FILS_ERP_USERNAME and
* %NL80211_ATTR_FILS_ERP_REALM. This is used for generating rIK and rMSK
* from successful FILS authentication and is used with
* %NL80211_CMD_CONNECT.
*
* @NL80211_ATTR_FILS_CACHE_ID: A 2-octet identifier advertized by a FILS AP
* identifying the scope of PMKSAs. This is used with
* @NL80211_CMD_SET_PMKSA and @NL80211_CMD_DEL_PMKSA.
*
* @NL80211_ATTR_PMK: attribute for passing PMK key material. Used with
* %NL80211_CMD_SET_PMKSA for the PMKSA identified by %NL80211_ATTR_PMKID.
* For %NL80211_CMD_CONNECT and %NL80211_CMD_START_AP it is used to provide
* PSK for offloading 4-way handshake for WPA/WPA2-PSK networks. For 802.1X
* authentication it is used with %NL80211_CMD_SET_PMK. For offloaded FT
* support this attribute specifies the PMK-R0 if NL80211_ATTR_PMKR0_NAME
* is included as well.
*
* @NL80211_ATTR_SCHED_SCAN_MULTI: flag attribute which user-space shall use to
* indicate that it supports multiple active scheduled scan requests.
* @NL80211_ATTR_SCHED_SCAN_MAX_REQS: indicates maximum number of scheduled
* scan request that may be active for the device (u32).
*
* @NL80211_ATTR_WANT_1X_4WAY_HS: flag attribute which user-space can include
* in %NL80211_CMD_CONNECT to indicate that for 802.1X authentication it
* wants to use the supported offload of the 4-way handshake.
* @NL80211_ATTR_PMKR0_NAME: PMK-R0 Name for offloaded FT.
* @NL80211_ATTR_PORT_AUTHORIZED: (reserved)
*
* @NL80211_ATTR_EXTERNAL_AUTH_ACTION: Identify the requested external
* authentication operation (u32 attribute with an
* &enum nl80211_external_auth_action value). This is used with the
* %NL80211_CMD_EXTERNAL_AUTH request event.
* @NL80211_ATTR_EXTERNAL_AUTH_SUPPORT: Flag attribute indicating that the user
* space supports external authentication. This attribute shall be used
* with %NL80211_CMD_CONNECT and %NL80211_CMD_START_AP request. The driver
* may offload authentication processing to user space if this capability
* is indicated in the respective requests from the user space. (This flag
* attribute deprecated for %NL80211_CMD_START_AP, use
* %NL80211_ATTR_AP_SETTINGS_FLAGS)
*
* @NL80211_ATTR_NSS: Station's New/updated RX_NSS value notified using this
* u8 attribute. This is used with %NL80211_CMD_STA_OPMODE_CHANGED.
*
* @NL80211_ATTR_TXQ_STATS: TXQ statistics (nested attribute, see &enum
* nl80211_txq_stats)
* @NL80211_ATTR_TXQ_LIMIT: Total packet limit for the TXQ queues for this phy.
* The smaller of this and the memory limit is enforced.
* @NL80211_ATTR_TXQ_MEMORY_LIMIT: Total memory limit (in bytes) for the
* TXQ queues for this phy. The smaller of this and the packet limit is
* enforced.
* @NL80211_ATTR_TXQ_QUANTUM: TXQ scheduler quantum (bytes). Number of bytes
* a flow is assigned on each round of the DRR scheduler.
* @NL80211_ATTR_HE_CAPABILITY: HE Capability information element (from
* association request when used with NL80211_CMD_NEW_STATION). Can be set
* only if %NL80211_STA_FLAG_WME is set.
*
* @NL80211_ATTR_FTM_RESPONDER: nested attribute which user-space can include
* in %NL80211_CMD_START_AP or %NL80211_CMD_SET_BEACON for fine timing
* measurement (FTM) responder functionality and containing parameters as
* possible, see &enum nl80211_ftm_responder_attr
*
* @NL80211_ATTR_FTM_RESPONDER_STATS: Nested attribute with FTM responder
* statistics, see &enum nl80211_ftm_responder_stats.
*
* @NL80211_ATTR_TIMEOUT: Timeout for the given operation in milliseconds (u32),
* if the attribute is not given no timeout is requested. Note that 0 is an
* invalid value.
*
* @NL80211_ATTR_PEER_MEASUREMENTS: peer measurements request (and result)
* data, uses nested attributes specified in
* &enum nl80211_peer_measurement_attrs.
* This is also used for capability advertisement in the wiphy information,
* with the appropriate sub-attributes.
*
* @NL80211_ATTR_AIRTIME_WEIGHT: Station's weight when scheduled by the airtime
* scheduler.
*
* @NL80211_ATTR_STA_TX_POWER_SETTING: Transmit power setting type (u8) for
* station associated with the AP. See &enum nl80211_tx_power_setting for
* possible values.
* @NL80211_ATTR_STA_TX_POWER: Transmit power level (s16) in dBm units. This
* allows to set Tx power for a station. If this attribute is not included,
* the default per-interface tx power setting will be overriding. Driver
* should be picking up the lowest tx power, either tx power per-interface
* or per-station.
*
* @NL80211_ATTR_SAE_PASSWORD: attribute for passing SAE password material. It
* is used with %NL80211_CMD_CONNECT to provide password for offloading
* SAE authentication for WPA3-Personal networks.
*
* @NL80211_ATTR_TWT_RESPONDER: Enable target wait time responder support.
*
* @NL80211_ATTR_HE_OBSS_PD: nested attribute for OBSS Packet Detection
* functionality.
*
* @NL80211_ATTR_WIPHY_EDMG_CHANNELS: bitmap that indicates the 2.16 GHz
* channel(s) that are allowed to be used for EDMG transmissions.
* Defined by IEEE P802.11ay/D4.0 section 9.4.2.251. (u8 attribute)
* @NL80211_ATTR_WIPHY_EDMG_BW_CONFIG: Channel BW Configuration subfield encodes
* the allowed channel bandwidth configurations. (u8 attribute)
* Defined by IEEE P802.11ay/D4.0 section 9.4.2.251, Table 13.
*
* @NL80211_ATTR_VLAN_ID: VLAN ID (1..4094) for the station and VLAN group key
* (u16).
*
* @NL80211_ATTR_HE_BSS_COLOR: nested attribute for BSS Color Settings.
*
* @NL80211_ATTR_IFTYPE_AKM_SUITES: nested array attribute, with each entry
* using attributes from &enum nl80211_iftype_akm_attributes. This
* attribute is sent in a response to %NL80211_CMD_GET_WIPHY indicating
* supported AKM suites capability per interface. AKMs advertised in
* %NL80211_ATTR_AKM_SUITES are default capabilities if AKM suites not
* advertised for a specific interface type.
*
* @NL80211_ATTR_TID_CONFIG: TID specific configuration in a
* nested attribute with &enum nl80211_tid_config_attr sub-attributes;
* on output (in wiphy attributes) it contains only the feature sub-
* attributes.
*
* @NL80211_ATTR_CONTROL_PORT_NO_PREAUTH: disable preauth frame rx on control
* port in order to forward/receive them as ordinary data frames.
*
* @NL80211_ATTR_PMK_LIFETIME: Maximum lifetime for PMKSA in seconds (u32,
* dot11RSNAConfigPMKReauthThreshold; 0 is not a valid value).
* An optional parameter configured through %NL80211_CMD_SET_PMKSA.
* Drivers that trigger roaming need to know the lifetime of the
* configured PMKSA for triggering the full vs. PMKSA caching based
* authentication. This timeout helps authentication methods like SAE,
* where PMK gets updated only by going through a full (new SAE)
* authentication instead of getting updated during an association for EAP
* authentication. No new full authentication within the PMK expiry shall
* result in a disassociation at the end of the lifetime.
*
* @NL80211_ATTR_PMK_REAUTH_THRESHOLD: Reauthentication threshold time, in
* terms of percentage of %NL80211_ATTR_PMK_LIFETIME
* (u8, dot11RSNAConfigPMKReauthThreshold, 1..100). This is an optional
* parameter configured through %NL80211_CMD_SET_PMKSA. Requests the
* driver to trigger a full authentication roam (without PMKSA caching)
* after the reauthentication threshold time, but before the PMK lifetime
* has expired.
*
* Authentication methods like SAE need to be able to generate a new PMKSA
* entry without having to force a disconnection after the PMK timeout. If
* no roaming occurs between the reauth threshold and PMK expiration,
* disassociation is still forced.
* @NL80211_ATTR_RECEIVE_MULTICAST: multicast flag for the
* %NL80211_CMD_REGISTER_FRAME command, see the description there.
* @NL80211_ATTR_WIPHY_FREQ_OFFSET: offset of the associated
* %NL80211_ATTR_WIPHY_FREQ in positive KHz. Only valid when supplied with
* an %NL80211_ATTR_WIPHY_FREQ_OFFSET.
* @NL80211_ATTR_CENTER_FREQ1_OFFSET: Center frequency offset in KHz for the
* first channel segment specified in %NL80211_ATTR_CENTER_FREQ1.
* @NL80211_ATTR_SCAN_FREQ_KHZ: nested attribute with KHz frequencies
*
* @NL80211_ATTR_HE_6GHZ_CAPABILITY: HE 6 GHz Band Capability element (from
* association request when used with NL80211_CMD_NEW_STATION).
*
* @NL80211_ATTR_FILS_DISCOVERY: Optional parameter to configure FILS
* discovery. It is a nested attribute, see
* &enum nl80211_fils_discovery_attributes.
*
* @NL80211_ATTR_UNSOL_BCAST_PROBE_RESP: Optional parameter to configure
* unsolicited broadcast probe response. It is a nested attribute, see
* &enum nl80211_unsol_bcast_probe_resp_attributes.
*
* @NL80211_ATTR_S1G_CAPABILITY: S1G Capability information element (from
* association request when used with NL80211_CMD_NEW_STATION)
* @NL80211_ATTR_S1G_CAPABILITY_MASK: S1G Capability Information element
* override mask. Used with NL80211_ATTR_S1G_CAPABILITY in
* NL80211_CMD_ASSOCIATE or NL80211_CMD_CONNECT.
*
* @NL80211_ATTR_SAE_PWE: Indicates the mechanism(s) allowed for SAE PWE
* derivation in WPA3-Personal networks which are using SAE authentication.
* This is a u8 attribute that encapsulates one of the values from
* &enum nl80211_sae_pwe_mechanism.
*
* @NL80211_ATTR_SAR_SPEC: SAR power limitation specification when
* used with %NL80211_CMD_SET_SAR_SPECS. The message contains fields
* of %nl80211_sar_attrs which specifies the sar type and related
* sar specs. Sar specs contains array of %nl80211_sar_specs_attrs.
*
* @NL80211_ATTR_RECONNECT_REQUESTED: flag attribute, used with deauth and
* disassoc events to indicate that an immediate reconnect to the AP
* is desired.
*
* @NL80211_ATTR_OBSS_COLOR_BITMAP: bitmap of the u64 BSS colors for the
* %NL80211_CMD_OBSS_COLOR_COLLISION event.
*
* @NL80211_ATTR_COLOR_CHANGE_COUNT: u8 attribute specifying the number of TBTT's
* until the color switch event.
* @NL80211_ATTR_COLOR_CHANGE_COLOR: u8 attribute specifying the color that we are
* switching to
* @NL80211_ATTR_COLOR_CHANGE_ELEMS: Nested set of attributes containing the IE
* information for the time while performing a color switch.
*
* @NL80211_ATTR_MBSSID_CONFIG: Nested attribute for multiple BSSID
* advertisements (MBSSID) parameters in AP mode.
* Kernel uses this attribute to indicate the driver's support for MBSSID
* and enhanced multi-BSSID advertisements (EMA AP) to the userspace.
* Userspace should use this attribute to configure per interface MBSSID
* parameters.
* See &enum nl80211_mbssid_config_attributes for details.
*
* @NL80211_ATTR_MBSSID_ELEMS: Nested parameter to pass multiple BSSID elements.
* Mandatory parameter for the transmitting interface to enable MBSSID.
* Optional for the non-transmitting interfaces.
*
* @NL80211_ATTR_RADAR_BACKGROUND: Configure dedicated offchannel chain
* available for radar/CAC detection on some hw. This chain can't be used
* to transmit or receive frames and it is bounded to a running wdev.
* Background radar/CAC detection allows to avoid the CAC downtime
* switching on a different channel during CAC detection on the selected
* radar channel.
*
* @NL80211_ATTR_AP_SETTINGS_FLAGS: u32 attribute contains ap settings flags,
* enumerated in &enum nl80211_ap_settings_flags. This attribute shall be
* used with %NL80211_CMD_START_AP request.
*
* @NL80211_ATTR_EHT_CAPABILITY: EHT Capability information element (from
* association request when used with NL80211_CMD_NEW_STATION). Can be set
* only if %NL80211_STA_FLAG_WME is set.
*
* @NL80211_ATTR_MLO_LINK_ID: A (u8) link ID for use with MLO, to be used with
* various commands that need a link ID to operate.
* @NL80211_ATTR_MLO_LINKS: A nested array of links, each containing some
* per-link information and a link ID.
* @NL80211_ATTR_MLD_ADDR: An MLD address, used with various commands such as
* authenticate/associate.
*
* @NL80211_ATTR_MLO_SUPPORT: Flag attribute to indicate user space supports MLO
* connection. Used with %NL80211_CMD_CONNECT. If this attribute is not
* included in NL80211_CMD_CONNECT drivers must not perform MLO connection.
*
* @NL80211_ATTR_MAX_NUM_AKM_SUITES: U16 attribute. Indicates maximum number of
* AKM suites allowed for %NL80211_CMD_CONNECT, %NL80211_CMD_ASSOCIATE and
* %NL80211_CMD_START_AP in %NL80211_CMD_GET_WIPHY response. If this
* attribute is not present userspace shall consider maximum number of AKM
* suites allowed as %NL80211_MAX_NR_AKM_SUITES which is the legacy maximum
* number prior to the introduction of this attribute.
*
* @NL80211_ATTR_EML_CAPABILITY: EML Capability information (u16)
* @NL80211_ATTR_MLD_CAPA_AND_OPS: MLD Capabilities and Operations (u16)
*
* @NL80211_ATTR_TX_HW_TIMESTAMP: Hardware timestamp for TX operation in
* nanoseconds (u64). This is the device clock timestamp so it will
* probably reset when the device is stopped or the firmware is reset.
* When used with %NL80211_CMD_FRAME_TX_STATUS, indicates the frame TX
* timestamp. When used with %NL80211_CMD_FRAME RX notification, indicates
* the ack TX timestamp.
* @NL80211_ATTR_RX_HW_TIMESTAMP: Hardware timestamp for RX operation in
* nanoseconds (u64). This is the device clock timestamp so it will
* probably reset when the device is stopped or the firmware is reset.
* When used with %NL80211_CMD_FRAME_TX_STATUS, indicates the ack RX
* timestamp. When used with %NL80211_CMD_FRAME RX notification, indicates
* the incoming frame RX timestamp.
* @NL80211_ATTR_TD_BITMAP: Transition Disable bitmap, for subsequent
* (re)associations.
*
* @NL80211_ATTR_PUNCT_BITMAP: (u32) Preamble puncturing bitmap, lowest
* bit corresponds to the lowest 20 MHz channel. Each bit set to 1
* indicates that the sub-channel is punctured. Higher 16 bits are
* reserved.
*
* @NL80211_ATTR_MAX_HW_TIMESTAMP_PEERS: Maximum number of peers that HW
* timestamping can be enabled for concurrently (u16), a wiphy attribute.
* A value of 0xffff indicates setting for all peers (i.e. not specifying
* an address with %NL80211_CMD_SET_HW_TIMESTAMP) is supported.
* @NL80211_ATTR_HW_TIMESTAMP_ENABLED: Indicates whether HW timestamping should
* be enabled or not (flag attribute).
*
* @NL80211_ATTR_EMA_RNR_ELEMS: Optional nested attribute for
* reduced neighbor report (RNR) elements. This attribute can be used
* only when NL80211_MBSSID_CONFIG_ATTR_EMA is enabled.
* Userspace is responsible for splitting the RNR into multiple
* elements such that each element excludes the non-transmitting
* profiles already included in the MBSSID element
* (%NL80211_ATTR_MBSSID_ELEMS) at the same index. Each EMA beacon
* will be generated by adding MBSSID and RNR elements at the same
* index. If the userspace includes more RNR elements than number of
* MBSSID elements then these will be added in every EMA beacon.
*
* @NUM_NL80211_ATTR: total number of nl80211_attrs available
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
*/
enum nl80211_attrs {
/* don't change the order or add anything between, this is ABI! */
NL80211_ATTR_UNSPEC,
NL80211_ATTR_WIPHY,
NL80211_ATTR_WIPHY_NAME,
NL80211_ATTR_IFINDEX,
NL80211_ATTR_IFNAME,
NL80211_ATTR_IFTYPE,
NL80211_ATTR_MAC,
NL80211_ATTR_KEY_DATA,
NL80211_ATTR_KEY_IDX,
NL80211_ATTR_KEY_CIPHER,
NL80211_ATTR_KEY_SEQ,
NL80211_ATTR_KEY_DEFAULT,
NL80211_ATTR_BEACON_INTERVAL,
NL80211_ATTR_DTIM_PERIOD,
NL80211_ATTR_BEACON_HEAD,
NL80211_ATTR_BEACON_TAIL,
NL80211_ATTR_STA_AID,
NL80211_ATTR_STA_FLAGS,
NL80211_ATTR_STA_LISTEN_INTERVAL,
NL80211_ATTR_STA_SUPPORTED_RATES,
NL80211_ATTR_STA_VLAN,
NL80211_ATTR_STA_INFO,
NL80211_ATTR_WIPHY_BANDS,
NL80211_ATTR_MNTR_FLAGS,
NL80211_ATTR_MESH_ID,
NL80211_ATTR_STA_PLINK_ACTION,
NL80211_ATTR_MPATH_NEXT_HOP,
NL80211_ATTR_MPATH_INFO,
NL80211_ATTR_BSS_CTS_PROT,
NL80211_ATTR_BSS_SHORT_PREAMBLE,
NL80211_ATTR_BSS_SHORT_SLOT_TIME,
NL80211_ATTR_HT_CAPABILITY,
NL80211_ATTR_SUPPORTED_IFTYPES,
NL80211_ATTR_REG_ALPHA2,
NL80211_ATTR_REG_RULES,
NL80211_ATTR_MESH_CONFIG,
NL80211_ATTR_BSS_BASIC_RATES,
NL80211_ATTR_WIPHY_TXQ_PARAMS,
NL80211_ATTR_WIPHY_FREQ,
NL80211_ATTR_WIPHY_CHANNEL_TYPE,
NL80211_ATTR_KEY_DEFAULT_MGMT,
NL80211_ATTR_MGMT_SUBTYPE,
NL80211_ATTR_IE,
NL80211_ATTR_MAX_NUM_SCAN_SSIDS,
NL80211_ATTR_SCAN_FREQUENCIES,
NL80211_ATTR_SCAN_SSIDS,
NL80211_ATTR_GENERATION, /* replaces old SCAN_GENERATION */
NL80211_ATTR_BSS,
NL80211_ATTR_REG_INITIATOR,
NL80211_ATTR_REG_TYPE,
NL80211_ATTR_SUPPORTED_COMMANDS,
NL80211_ATTR_FRAME,
NL80211_ATTR_SSID,
NL80211_ATTR_AUTH_TYPE,
NL80211_ATTR_REASON_CODE,
NL80211_ATTR_KEY_TYPE,
NL80211_ATTR_MAX_SCAN_IE_LEN,
NL80211_ATTR_CIPHER_SUITES,
NL80211_ATTR_FREQ_BEFORE,
NL80211_ATTR_FREQ_AFTER,
NL80211_ATTR_FREQ_FIXED,
NL80211_ATTR_WIPHY_RETRY_SHORT,
NL80211_ATTR_WIPHY_RETRY_LONG,
NL80211_ATTR_WIPHY_FRAG_THRESHOLD,
NL80211_ATTR_WIPHY_RTS_THRESHOLD,
NL80211_ATTR_TIMED_OUT,
NL80211_ATTR_USE_MFP,
NL80211_ATTR_STA_FLAGS2,
NL80211_ATTR_CONTROL_PORT,
NL80211_ATTR_TESTDATA,
NL80211_ATTR_PRIVACY,
NL80211_ATTR_DISCONNECTED_BY_AP,
NL80211_ATTR_STATUS_CODE,
NL80211_ATTR_CIPHER_SUITES_PAIRWISE,
NL80211_ATTR_CIPHER_SUITE_GROUP,
NL80211_ATTR_WPA_VERSIONS,
NL80211_ATTR_AKM_SUITES,
NL80211_ATTR_REQ_IE,
NL80211_ATTR_RESP_IE,
NL80211_ATTR_PREV_BSSID,
NL80211_ATTR_KEY,
NL80211_ATTR_KEYS,
NL80211_ATTR_PID,
NL80211_ATTR_4ADDR,
NL80211_ATTR_SURVEY_INFO,
NL80211_ATTR_PMKID,
NL80211_ATTR_MAX_NUM_PMKIDS,
NL80211_ATTR_DURATION,
NL80211_ATTR_COOKIE,
NL80211_ATTR_WIPHY_COVERAGE_CLASS,
NL80211_ATTR_TX_RATES,
NL80211_ATTR_FRAME_MATCH,
NL80211_ATTR_ACK,
NL80211_ATTR_PS_STATE,
NL80211_ATTR_CQM,
NL80211_ATTR_LOCAL_STATE_CHANGE,
NL80211_ATTR_AP_ISOLATE,
NL80211_ATTR_WIPHY_TX_POWER_SETTING,
NL80211_ATTR_WIPHY_TX_POWER_LEVEL,
NL80211_ATTR_TX_FRAME_TYPES,
NL80211_ATTR_RX_FRAME_TYPES,
NL80211_ATTR_FRAME_TYPE,
NL80211_ATTR_CONTROL_PORT_ETHERTYPE,
NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT,
NL80211_ATTR_SUPPORT_IBSS_RSN,
NL80211_ATTR_WIPHY_ANTENNA_TX,
NL80211_ATTR_WIPHY_ANTENNA_RX,
NL80211_ATTR_MCAST_RATE,
NL80211_ATTR_OFFCHANNEL_TX_OK,
NL80211_ATTR_BSS_HT_OPMODE,
NL80211_ATTR_KEY_DEFAULT_TYPES,
NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION,
NL80211_ATTR_MESH_SETUP,
NL80211_ATTR_WIPHY_ANTENNA_AVAIL_TX,
NL80211_ATTR_WIPHY_ANTENNA_AVAIL_RX,
NL80211_ATTR_SUPPORT_MESH_AUTH,
NL80211_ATTR_STA_PLINK_STATE,
NL80211_ATTR_WOWLAN_TRIGGERS,
NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED,
NL80211_ATTR_SCHED_SCAN_INTERVAL,
NL80211_ATTR_INTERFACE_COMBINATIONS,
NL80211_ATTR_SOFTWARE_IFTYPES,
NL80211_ATTR_REKEY_DATA,
NL80211_ATTR_MAX_NUM_SCHED_SCAN_SSIDS,
NL80211_ATTR_MAX_SCHED_SCAN_IE_LEN,
NL80211_ATTR_SCAN_SUPP_RATES,
NL80211_ATTR_HIDDEN_SSID,
NL80211_ATTR_IE_PROBE_RESP,
NL80211_ATTR_IE_ASSOC_RESP,
NL80211_ATTR_STA_WME,
NL80211_ATTR_SUPPORT_AP_UAPSD,
NL80211_ATTR_ROAM_SUPPORT,
NL80211_ATTR_SCHED_SCAN_MATCH,
NL80211_ATTR_MAX_MATCH_SETS,
NL80211_ATTR_PMKSA_CANDIDATE,
NL80211_ATTR_TX_NO_CCK_RATE,
NL80211_ATTR_TDLS_ACTION,
NL80211_ATTR_TDLS_DIALOG_TOKEN,
NL80211_ATTR_TDLS_OPERATION,
NL80211_ATTR_TDLS_SUPPORT,
NL80211_ATTR_TDLS_EXTERNAL_SETUP,
NL80211_ATTR_DEVICE_AP_SME,
NL80211_ATTR_DONT_WAIT_FOR_ACK,
NL80211_ATTR_FEATURE_FLAGS,
NL80211_ATTR_PROBE_RESP_OFFLOAD,
NL80211_ATTR_PROBE_RESP,
NL80211_ATTR_DFS_REGION,
NL80211_ATTR_DISABLE_HT,
NL80211_ATTR_HT_CAPABILITY_MASK,
NL80211_ATTR_NOACK_MAP,
NL80211_ATTR_INACTIVITY_TIMEOUT,
NL80211_ATTR_RX_SIGNAL_DBM,
NL80211_ATTR_BG_SCAN_PERIOD,
NL80211_ATTR_WDEV,
NL80211_ATTR_USER_REG_HINT_TYPE,
NL80211_ATTR_CONN_FAILED_REASON,
NL80211_ATTR_AUTH_DATA,
NL80211_ATTR_VHT_CAPABILITY,
NL80211_ATTR_SCAN_FLAGS,
NL80211_ATTR_CHANNEL_WIDTH,
NL80211_ATTR_CENTER_FREQ1,
NL80211_ATTR_CENTER_FREQ2,
NL80211_ATTR_P2P_CTWINDOW,
NL80211_ATTR_P2P_OPPPS,
NL80211_ATTR_LOCAL_MESH_POWER_MODE,
NL80211_ATTR_ACL_POLICY,
NL80211_ATTR_MAC_ADDRS,
NL80211_ATTR_MAC_ACL_MAX,
NL80211_ATTR_RADAR_EVENT,
NL80211_ATTR_EXT_CAPA,
NL80211_ATTR_EXT_CAPA_MASK,
NL80211_ATTR_STA_CAPABILITY,
NL80211_ATTR_STA_EXT_CAPABILITY,
NL80211_ATTR_PROTOCOL_FEATURES,
NL80211_ATTR_SPLIT_WIPHY_DUMP,
NL80211_ATTR_DISABLE_VHT,
NL80211_ATTR_VHT_CAPABILITY_MASK,
NL80211_ATTR_MDID,
NL80211_ATTR_IE_RIC,
NL80211_ATTR_CRIT_PROT_ID,
NL80211_ATTR_MAX_CRIT_PROT_DURATION,
NL80211_ATTR_PEER_AID,
NL80211_ATTR_COALESCE_RULE,
NL80211_ATTR_CH_SWITCH_COUNT,
NL80211_ATTR_CH_SWITCH_BLOCK_TX,
NL80211_ATTR_CSA_IES,
NL80211_ATTR_CNTDWN_OFFS_BEACON,
NL80211_ATTR_CNTDWN_OFFS_PRESP,
NL80211_ATTR_RXMGMT_FLAGS,
NL80211_ATTR_STA_SUPPORTED_CHANNELS,
NL80211_ATTR_STA_SUPPORTED_OPER_CLASSES,
NL80211_ATTR_HANDLE_DFS,
NL80211_ATTR_SUPPORT_5_MHZ,
NL80211_ATTR_SUPPORT_10_MHZ,
NL80211_ATTR_OPMODE_NOTIF,
NL80211_ATTR_VENDOR_ID,
NL80211_ATTR_VENDOR_SUBCMD,
NL80211_ATTR_VENDOR_DATA,
NL80211_ATTR_VENDOR_EVENTS,
NL80211_ATTR_QOS_MAP,
NL80211_ATTR_MAC_HINT,
NL80211_ATTR_WIPHY_FREQ_HINT,
NL80211_ATTR_MAX_AP_ASSOC_STA,
NL80211_ATTR_TDLS_PEER_CAPABILITY,
NL80211_ATTR_SOCKET_OWNER,
NL80211_ATTR_CSA_C_OFFSETS_TX,
NL80211_ATTR_MAX_CSA_COUNTERS,
NL80211_ATTR_TDLS_INITIATOR,
NL80211_ATTR_USE_RRM,
NL80211_ATTR_WIPHY_DYN_ACK,
NL80211_ATTR_TSID,
NL80211_ATTR_USER_PRIO,
NL80211_ATTR_ADMITTED_TIME,
NL80211_ATTR_SMPS_MODE,
NL80211_ATTR_OPER_CLASS,
NL80211_ATTR_MAC_MASK,
NL80211_ATTR_WIPHY_SELF_MANAGED_REG,
NL80211_ATTR_EXT_FEATURES,
NL80211_ATTR_SURVEY_RADIO_STATS,
NL80211_ATTR_NETNS_FD,
NL80211_ATTR_SCHED_SCAN_DELAY,
NL80211_ATTR_REG_INDOOR,
NL80211_ATTR_MAX_NUM_SCHED_SCAN_PLANS,
NL80211_ATTR_MAX_SCAN_PLAN_INTERVAL,
NL80211_ATTR_MAX_SCAN_PLAN_ITERATIONS,
NL80211_ATTR_SCHED_SCAN_PLANS,
NL80211_ATTR_PBSS,
NL80211_ATTR_BSS_SELECT,
NL80211_ATTR_STA_SUPPORT_P2P_PS,
NL80211_ATTR_PAD,
NL80211_ATTR_IFTYPE_EXT_CAPA,
NL80211_ATTR_MU_MIMO_GROUP_DATA,
NL80211_ATTR_MU_MIMO_FOLLOW_MAC_ADDR,
NL80211_ATTR_SCAN_START_TIME_TSF,
NL80211_ATTR_SCAN_START_TIME_TSF_BSSID,
NL80211_ATTR_MEASUREMENT_DURATION,
NL80211_ATTR_MEASUREMENT_DURATION_MANDATORY,
NL80211_ATTR_MESH_PEER_AID,
NL80211_ATTR_NAN_MASTER_PREF,
NL80211_ATTR_BANDS,
NL80211_ATTR_NAN_FUNC,
NL80211_ATTR_NAN_MATCH,
NL80211_ATTR_FILS_KEK,
NL80211_ATTR_FILS_NONCES,
NL80211_ATTR_MULTICAST_TO_UNICAST_ENABLED,
NL80211_ATTR_BSSID,
NL80211_ATTR_SCHED_SCAN_RELATIVE_RSSI,
NL80211_ATTR_SCHED_SCAN_RSSI_ADJUST,
NL80211_ATTR_TIMEOUT_REASON,
NL80211_ATTR_FILS_ERP_USERNAME,
NL80211_ATTR_FILS_ERP_REALM,
NL80211_ATTR_FILS_ERP_NEXT_SEQ_NUM,
NL80211_ATTR_FILS_ERP_RRK,
NL80211_ATTR_FILS_CACHE_ID,
NL80211_ATTR_PMK,
NL80211_ATTR_SCHED_SCAN_MULTI,
NL80211_ATTR_SCHED_SCAN_MAX_REQS,
NL80211_ATTR_WANT_1X_4WAY_HS,
NL80211_ATTR_PMKR0_NAME,
NL80211_ATTR_PORT_AUTHORIZED,
NL80211_ATTR_EXTERNAL_AUTH_ACTION,
NL80211_ATTR_EXTERNAL_AUTH_SUPPORT,
NL80211_ATTR_NSS,
NL80211_ATTR_ACK_SIGNAL,
NL80211_ATTR_CONTROL_PORT_OVER_NL80211,
NL80211_ATTR_TXQ_STATS,
NL80211_ATTR_TXQ_LIMIT,
NL80211_ATTR_TXQ_MEMORY_LIMIT,
NL80211_ATTR_TXQ_QUANTUM,
NL80211_ATTR_HE_CAPABILITY,
NL80211_ATTR_FTM_RESPONDER,
NL80211_ATTR_FTM_RESPONDER_STATS,
NL80211_ATTR_TIMEOUT,
NL80211_ATTR_PEER_MEASUREMENTS,
NL80211_ATTR_AIRTIME_WEIGHT,
NL80211_ATTR_STA_TX_POWER_SETTING,
NL80211_ATTR_STA_TX_POWER,
NL80211_ATTR_SAE_PASSWORD,
NL80211_ATTR_TWT_RESPONDER,
NL80211_ATTR_HE_OBSS_PD,
NL80211_ATTR_WIPHY_EDMG_CHANNELS,
NL80211_ATTR_WIPHY_EDMG_BW_CONFIG,
NL80211_ATTR_VLAN_ID,
NL80211_ATTR_HE_BSS_COLOR,
NL80211_ATTR_IFTYPE_AKM_SUITES,
NL80211_ATTR_TID_CONFIG,
NL80211_ATTR_CONTROL_PORT_NO_PREAUTH,
NL80211_ATTR_PMK_LIFETIME,
NL80211_ATTR_PMK_REAUTH_THRESHOLD,
NL80211_ATTR_RECEIVE_MULTICAST,
NL80211_ATTR_WIPHY_FREQ_OFFSET,
NL80211_ATTR_CENTER_FREQ1_OFFSET,
NL80211_ATTR_SCAN_FREQ_KHZ,
NL80211_ATTR_HE_6GHZ_CAPABILITY,
NL80211_ATTR_FILS_DISCOVERY,
NL80211_ATTR_UNSOL_BCAST_PROBE_RESP,
NL80211_ATTR_S1G_CAPABILITY,
NL80211_ATTR_S1G_CAPABILITY_MASK,
NL80211_ATTR_SAE_PWE,
NL80211_ATTR_RECONNECT_REQUESTED,
NL80211_ATTR_SAR_SPEC,
NL80211_ATTR_DISABLE_HE,
NL80211_ATTR_OBSS_COLOR_BITMAP,
NL80211_ATTR_COLOR_CHANGE_COUNT,
NL80211_ATTR_COLOR_CHANGE_COLOR,
NL80211_ATTR_COLOR_CHANGE_ELEMS,
NL80211_ATTR_MBSSID_CONFIG,
NL80211_ATTR_MBSSID_ELEMS,
NL80211_ATTR_RADAR_BACKGROUND,
NL80211_ATTR_AP_SETTINGS_FLAGS,
NL80211_ATTR_EHT_CAPABILITY,
NL80211_ATTR_DISABLE_EHT,
NL80211_ATTR_MLO_LINKS,
NL80211_ATTR_MLO_LINK_ID,
NL80211_ATTR_MLD_ADDR,
NL80211_ATTR_MLO_SUPPORT,
NL80211_ATTR_MAX_NUM_AKM_SUITES,
NL80211_ATTR_EML_CAPABILITY,
NL80211_ATTR_MLD_CAPA_AND_OPS,
NL80211_ATTR_TX_HW_TIMESTAMP,
NL80211_ATTR_RX_HW_TIMESTAMP,
NL80211_ATTR_TD_BITMAP,
NL80211_ATTR_PUNCT_BITMAP,
NL80211_ATTR_MAX_HW_TIMESTAMP_PEERS,
NL80211_ATTR_HW_TIMESTAMP_ENABLED,
NL80211_ATTR_EMA_RNR_ELEMS,
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
NUM_NL80211_ATTR = __NL80211_ATTR_AFTER_LAST,
NL80211_ATTR_MAX = __NL80211_ATTR_AFTER_LAST - 1
};
/* source-level API compatibility */
#define NL80211_ATTR_SCAN_GENERATION NL80211_ATTR_GENERATION
#define NL80211_ATTR_MESH_PARAMS NL80211_ATTR_MESH_CONFIG
#define NL80211_ATTR_IFACE_SOCKET_OWNER NL80211_ATTR_SOCKET_OWNER
#define NL80211_ATTR_SAE_DATA NL80211_ATTR_AUTH_DATA
#define NL80211_ATTR_CSA_C_OFF_BEACON NL80211_ATTR_CNTDWN_OFFS_BEACON
#define NL80211_ATTR_CSA_C_OFF_PRESP NL80211_ATTR_CNTDWN_OFFS_PRESP
/*
* Allow user space programs to use #ifdef on new attributes by defining them
* here
*/
#define NL80211_CMD_CONNECT NL80211_CMD_CONNECT
#define NL80211_ATTR_HT_CAPABILITY NL80211_ATTR_HT_CAPABILITY
#define NL80211_ATTR_BSS_BASIC_RATES NL80211_ATTR_BSS_BASIC_RATES
#define NL80211_ATTR_WIPHY_TXQ_PARAMS NL80211_ATTR_WIPHY_TXQ_PARAMS
#define NL80211_ATTR_WIPHY_FREQ NL80211_ATTR_WIPHY_FREQ
#define NL80211_ATTR_WIPHY_CHANNEL_TYPE NL80211_ATTR_WIPHY_CHANNEL_TYPE
#define NL80211_ATTR_MGMT_SUBTYPE NL80211_ATTR_MGMT_SUBTYPE
#define NL80211_ATTR_IE NL80211_ATTR_IE
#define NL80211_ATTR_REG_INITIATOR NL80211_ATTR_REG_INITIATOR
#define NL80211_ATTR_REG_TYPE NL80211_ATTR_REG_TYPE
#define NL80211_ATTR_FRAME NL80211_ATTR_FRAME
#define NL80211_ATTR_SSID NL80211_ATTR_SSID
#define NL80211_ATTR_AUTH_TYPE NL80211_ATTR_AUTH_TYPE
#define NL80211_ATTR_REASON_CODE NL80211_ATTR_REASON_CODE
#define NL80211_ATTR_CIPHER_SUITES_PAIRWISE NL80211_ATTR_CIPHER_SUITES_PAIRWISE
#define NL80211_ATTR_CIPHER_SUITE_GROUP NL80211_ATTR_CIPHER_SUITE_GROUP
#define NL80211_ATTR_WPA_VERSIONS NL80211_ATTR_WPA_VERSIONS
#define NL80211_ATTR_AKM_SUITES NL80211_ATTR_AKM_SUITES
#define NL80211_ATTR_KEY NL80211_ATTR_KEY
#define NL80211_ATTR_KEYS NL80211_ATTR_KEYS
#define NL80211_ATTR_FEATURE_FLAGS NL80211_ATTR_FEATURE_FLAGS
#define NL80211_WIPHY_NAME_MAXLEN 64
#define NL80211_MAX_SUPP_RATES 32
#define NL80211_MAX_SUPP_HT_RATES 77
#define NL80211_MAX_SUPP_REG_RULES 128
#define NL80211_TKIP_DATA_OFFSET_ENCR_KEY 0
#define NL80211_TKIP_DATA_OFFSET_TX_MIC_KEY 16
#define NL80211_TKIP_DATA_OFFSET_RX_MIC_KEY 24
#define NL80211_HT_CAPABILITY_LEN 26
#define NL80211_VHT_CAPABILITY_LEN 12
#define NL80211_HE_MIN_CAPABILITY_LEN 16
#define NL80211_HE_MAX_CAPABILITY_LEN 54
#define NL80211_MAX_NR_CIPHER_SUITES 5
/*
* NL80211_MAX_NR_AKM_SUITES is obsolete when %NL80211_ATTR_MAX_NUM_AKM_SUITES
* present in %NL80211_CMD_GET_WIPHY response.
*/
#define NL80211_MAX_NR_AKM_SUITES 2
#define NL80211_EHT_MIN_CAPABILITY_LEN 13
#define NL80211_EHT_MAX_CAPABILITY_LEN 51
#define NL80211_MIN_REMAIN_ON_CHANNEL_TIME 10
/* default RSSI threshold for scan results if none specified. */
#define NL80211_SCAN_RSSI_THOLD_OFF -300
#define NL80211_CQM_TXE_MAX_INTVL 1800
/**
* enum nl80211_iftype - (virtual) interface types
*
* @NL80211_IFTYPE_UNSPECIFIED: unspecified type, driver decides
* @NL80211_IFTYPE_ADHOC: independent BSS member
* @NL80211_IFTYPE_STATION: managed BSS member
* @NL80211_IFTYPE_AP: access point
* @NL80211_IFTYPE_AP_VLAN: VLAN interface for access points; VLAN interfaces
* are a bit special in that they must always be tied to a pre-existing
* AP type interface.
* @NL80211_IFTYPE_WDS: wireless distribution interface
* @NL80211_IFTYPE_MONITOR: monitor interface receiving all frames
* @NL80211_IFTYPE_MESH_POINT: mesh point
* @NL80211_IFTYPE_P2P_CLIENT: P2P client
* @NL80211_IFTYPE_P2P_GO: P2P group owner
* @NL80211_IFTYPE_P2P_DEVICE: P2P device interface type, this is not a netdev
* and therefore can't be created in the normal ways, use the
* %NL80211_CMD_START_P2P_DEVICE and %NL80211_CMD_STOP_P2P_DEVICE
* commands to create and destroy one
* @NL80211_IFTYPE_OCB: Outside Context of a BSS
* This mode corresponds to the MIB variable dot11OCBActivated=true
* @NL80211_IFTYPE_NAN: NAN device interface type (not a netdev)
* @NL80211_IFTYPE_MAX: highest interface type number currently defined
* @NUM_NL80211_IFTYPES: number of defined interface types
*
* These values are used with the %NL80211_ATTR_IFTYPE
* to set the type of an interface.
*
*/
enum nl80211_iftype {
NL80211_IFTYPE_UNSPECIFIED,
NL80211_IFTYPE_ADHOC,
NL80211_IFTYPE_STATION,
NL80211_IFTYPE_AP,
NL80211_IFTYPE_AP_VLAN,
NL80211_IFTYPE_WDS,
NL80211_IFTYPE_MONITOR,
NL80211_IFTYPE_MESH_POINT,
NL80211_IFTYPE_P2P_CLIENT,
NL80211_IFTYPE_P2P_GO,
NL80211_IFTYPE_P2P_DEVICE,
NL80211_IFTYPE_OCB,
NL80211_IFTYPE_NAN,
/* keep last */
NUM_NL80211_IFTYPES,
NL80211_IFTYPE_MAX = NUM_NL80211_IFTYPES - 1
};
/**
* enum nl80211_sta_flags - station flags
*
* Station flags. When a station is added to an AP interface, it is
* assumed to be already associated (and hence authenticated.)
*
* @__NL80211_STA_FLAG_INVALID: attribute number 0 is reserved
* @NL80211_STA_FLAG_AUTHORIZED: station is authorized (802.1X)
* @NL80211_STA_FLAG_SHORT_PREAMBLE: station is capable of receiving frames
* with short barker preamble
* @NL80211_STA_FLAG_WME: station is WME/QoS capable
* @NL80211_STA_FLAG_MFP: station uses management frame protection
* @NL80211_STA_FLAG_AUTHENTICATED: station is authenticated
* @NL80211_STA_FLAG_TDLS_PEER: station is a TDLS peer -- this flag should
* only be used in managed mode (even in the flags mask). Note that the
* flag can't be changed, it is only valid while adding a station, and
* attempts to change it will silently be ignored (rather than rejected
* as errors.)
* @NL80211_STA_FLAG_ASSOCIATED: station is associated; used with drivers
* that support %NL80211_FEATURE_FULL_AP_CLIENT_STATE to transition a
* previously added station into associated state
* @NL80211_STA_FLAG_MAX: highest station flag number currently defined
* @__NL80211_STA_FLAG_AFTER_LAST: internal use
*/
enum nl80211_sta_flags {
__NL80211_STA_FLAG_INVALID,
NL80211_STA_FLAG_AUTHORIZED,
NL80211_STA_FLAG_SHORT_PREAMBLE,
NL80211_STA_FLAG_WME,
NL80211_STA_FLAG_MFP,
NL80211_STA_FLAG_AUTHENTICATED,
NL80211_STA_FLAG_TDLS_PEER,
NL80211_STA_FLAG_ASSOCIATED,
/* keep last */
__NL80211_STA_FLAG_AFTER_LAST,
NL80211_STA_FLAG_MAX = __NL80211_STA_FLAG_AFTER_LAST - 1
};
/**
* enum nl80211_sta_p2p_ps_status - station support of P2P PS
*
* @NL80211_P2P_PS_UNSUPPORTED: station doesn't support P2P PS mechanism
* @@NL80211_P2P_PS_SUPPORTED: station supports P2P PS mechanism
* @NUM_NL80211_P2P_PS_STATUS: number of values
*/
enum nl80211_sta_p2p_ps_status {
NL80211_P2P_PS_UNSUPPORTED = 0,
NL80211_P2P_PS_SUPPORTED,
NUM_NL80211_P2P_PS_STATUS,
};
#define NL80211_STA_FLAG_MAX_OLD_API NL80211_STA_FLAG_TDLS_PEER
/**
* struct nl80211_sta_flag_update - station flags mask/set
* @mask: mask of station flags to set
* @set: which values to set them to
*
* Both mask and set contain bits as per &enum nl80211_sta_flags.
*/
struct nl80211_sta_flag_update {
__u32 mask;
__u32 set;
} __attribute__((packed));
/**
* enum nl80211_he_gi - HE guard interval
* @NL80211_RATE_INFO_HE_GI_0_8: 0.8 usec
* @NL80211_RATE_INFO_HE_GI_1_6: 1.6 usec
* @NL80211_RATE_INFO_HE_GI_3_2: 3.2 usec
*/
enum nl80211_he_gi {
NL80211_RATE_INFO_HE_GI_0_8,
NL80211_RATE_INFO_HE_GI_1_6,
NL80211_RATE_INFO_HE_GI_3_2,
};
/**
* enum nl80211_he_ltf - HE long training field
* @NL80211_RATE_INFO_HE_1xLTF: 3.2 usec
* @NL80211_RATE_INFO_HE_2xLTF: 6.4 usec
* @NL80211_RATE_INFO_HE_4xLTF: 12.8 usec
*/
enum nl80211_he_ltf {
NL80211_RATE_INFO_HE_1XLTF,
NL80211_RATE_INFO_HE_2XLTF,
NL80211_RATE_INFO_HE_4XLTF,
};
/**
* enum nl80211_he_ru_alloc - HE RU allocation values
* @NL80211_RATE_INFO_HE_RU_ALLOC_26: 26-tone RU allocation
* @NL80211_RATE_INFO_HE_RU_ALLOC_52: 52-tone RU allocation
* @NL80211_RATE_INFO_HE_RU_ALLOC_106: 106-tone RU allocation
* @NL80211_RATE_INFO_HE_RU_ALLOC_242: 242-tone RU allocation
* @NL80211_RATE_INFO_HE_RU_ALLOC_484: 484-tone RU allocation
* @NL80211_RATE_INFO_HE_RU_ALLOC_996: 996-tone RU allocation
* @NL80211_RATE_INFO_HE_RU_ALLOC_2x996: 2x996-tone RU allocation
*/
enum nl80211_he_ru_alloc {
NL80211_RATE_INFO_HE_RU_ALLOC_26,
NL80211_RATE_INFO_HE_RU_ALLOC_52,
NL80211_RATE_INFO_HE_RU_ALLOC_106,
NL80211_RATE_INFO_HE_RU_ALLOC_242,
NL80211_RATE_INFO_HE_RU_ALLOC_484,
NL80211_RATE_INFO_HE_RU_ALLOC_996,
NL80211_RATE_INFO_HE_RU_ALLOC_2x996,
};
/**
* enum nl80211_eht_gi - EHT guard interval
* @NL80211_RATE_INFO_EHT_GI_0_8: 0.8 usec
* @NL80211_RATE_INFO_EHT_GI_1_6: 1.6 usec
* @NL80211_RATE_INFO_EHT_GI_3_2: 3.2 usec
*/
enum nl80211_eht_gi {
NL80211_RATE_INFO_EHT_GI_0_8,
NL80211_RATE_INFO_EHT_GI_1_6,
NL80211_RATE_INFO_EHT_GI_3_2,
};
/**
* enum nl80211_eht_ru_alloc - EHT RU allocation values
* @NL80211_RATE_INFO_EHT_RU_ALLOC_26: 26-tone RU allocation
* @NL80211_RATE_INFO_EHT_RU_ALLOC_52: 52-tone RU allocation
* @NL80211_RATE_INFO_EHT_RU_ALLOC_52P26: 52+26-tone RU allocation
* @NL80211_RATE_INFO_EHT_RU_ALLOC_106: 106-tone RU allocation
* @NL80211_RATE_INFO_EHT_RU_ALLOC_106P26: 106+26 tone RU allocation
* @NL80211_RATE_INFO_EHT_RU_ALLOC_242: 242-tone RU allocation
* @NL80211_RATE_INFO_EHT_RU_ALLOC_484: 484-tone RU allocation
* @NL80211_RATE_INFO_EHT_RU_ALLOC_484P242: 484+242 tone RU allocation
* @NL80211_RATE_INFO_EHT_RU_ALLOC_996: 996-tone RU allocation
* @NL80211_RATE_INFO_EHT_RU_ALLOC_996P484: 996+484 tone RU allocation
* @NL80211_RATE_INFO_EHT_RU_ALLOC_996P484P242: 996+484+242 tone RU allocation
* @NL80211_RATE_INFO_EHT_RU_ALLOC_2x996: 2x996-tone RU allocation
* @NL80211_RATE_INFO_EHT_RU_ALLOC_2x996P484: 2x996+484 tone RU allocation
* @NL80211_RATE_INFO_EHT_RU_ALLOC_3x996: 3x996-tone RU allocation
* @NL80211_RATE_INFO_EHT_RU_ALLOC_3x996P484: 3x996+484 tone RU allocation
* @NL80211_RATE_INFO_EHT_RU_ALLOC_4x996: 4x996-tone RU allocation
*/
enum nl80211_eht_ru_alloc {
NL80211_RATE_INFO_EHT_RU_ALLOC_26,
NL80211_RATE_INFO_EHT_RU_ALLOC_52,
NL80211_RATE_INFO_EHT_RU_ALLOC_52P26,
NL80211_RATE_INFO_EHT_RU_ALLOC_106,
NL80211_RATE_INFO_EHT_RU_ALLOC_106P26,
NL80211_RATE_INFO_EHT_RU_ALLOC_242,
NL80211_RATE_INFO_EHT_RU_ALLOC_484,
NL80211_RATE_INFO_EHT_RU_ALLOC_484P242,
NL80211_RATE_INFO_EHT_RU_ALLOC_996,
NL80211_RATE_INFO_EHT_RU_ALLOC_996P484,
NL80211_RATE_INFO_EHT_RU_ALLOC_996P484P242,
NL80211_RATE_INFO_EHT_RU_ALLOC_2x996,
NL80211_RATE_INFO_EHT_RU_ALLOC_2x996P484,
NL80211_RATE_INFO_EHT_RU_ALLOC_3x996,
NL80211_RATE_INFO_EHT_RU_ALLOC_3x996P484,
NL80211_RATE_INFO_EHT_RU_ALLOC_4x996,
};
/**
* enum nl80211_rate_info - bitrate information
*
* These attribute types are used with %NL80211_STA_INFO_TXRATE
* when getting information about the bitrate of a station.
* There are 2 attributes for bitrate, a legacy one that represents
* a 16-bit value, and new one that represents a 32-bit value.
* If the rate value fits into 16 bit, both attributes are reported
* with the same value. If the rate is too high to fit into 16 bits
* (>6.5535Gbps) only 32-bit attribute is included.
* User space tools encouraged to use the 32-bit attribute and fall
* back to the 16-bit one for compatibility with older kernels.
*
* @__NL80211_RATE_INFO_INVALID: attribute number 0 is reserved
* @NL80211_RATE_INFO_BITRATE: total bitrate (u16, 100kbit/s)
* @NL80211_RATE_INFO_MCS: mcs index for 802.11n (u8)
* @NL80211_RATE_INFO_40_MHZ_WIDTH: 40 MHz dualchannel bitrate
* @NL80211_RATE_INFO_SHORT_GI: 400ns guard interval
* @NL80211_RATE_INFO_BITRATE32: total bitrate (u32, 100kbit/s)
* @NL80211_RATE_INFO_MAX: highest rate_info number currently defined
* @NL80211_RATE_INFO_VHT_MCS: MCS index for VHT (u8)
* @NL80211_RATE_INFO_VHT_NSS: number of streams in VHT (u8)
* @NL80211_RATE_INFO_80_MHZ_WIDTH: 80 MHz VHT rate
* @NL80211_RATE_INFO_80P80_MHZ_WIDTH: unused - 80+80 is treated the
* same as 160 for purposes of the bitrates
* @NL80211_RATE_INFO_160_MHZ_WIDTH: 160 MHz VHT rate
* @NL80211_RATE_INFO_10_MHZ_WIDTH: 10 MHz width - note that this is
* a legacy rate and will be reported as the actual bitrate, i.e.
* half the base (20 MHz) rate
* @NL80211_RATE_INFO_5_MHZ_WIDTH: 5 MHz width - note that this is
* a legacy rate and will be reported as the actual bitrate, i.e.
* a quarter of the base (20 MHz) rate
* @NL80211_RATE_INFO_HE_MCS: HE MCS index (u8, 0-11)
* @NL80211_RATE_INFO_HE_NSS: HE NSS value (u8, 1-8)
* @NL80211_RATE_INFO_HE_GI: HE guard interval identifier
* (u8, see &enum nl80211_he_gi)
* @NL80211_RATE_INFO_HE_DCM: HE DCM value (u8, 0/1)
* @NL80211_RATE_INFO_RU_ALLOC: HE RU allocation, if not present then
* non-OFDMA was used (u8, see &enum nl80211_he_ru_alloc)
* @NL80211_RATE_INFO_320_MHZ_WIDTH: 320 MHz bitrate
* @NL80211_RATE_INFO_EHT_MCS: EHT MCS index (u8, 0-15)
* @NL80211_RATE_INFO_EHT_NSS: EHT NSS value (u8, 1-8)
* @NL80211_RATE_INFO_EHT_GI: EHT guard interval identifier
* (u8, see &enum nl80211_eht_gi)
* @NL80211_RATE_INFO_EHT_RU_ALLOC: EHT RU allocation, if not present then
* non-OFDMA was used (u8, see &enum nl80211_eht_ru_alloc)
* @__NL80211_RATE_INFO_AFTER_LAST: internal use
*/
enum nl80211_rate_info {
__NL80211_RATE_INFO_INVALID,
NL80211_RATE_INFO_BITRATE,
NL80211_RATE_INFO_MCS,
NL80211_RATE_INFO_40_MHZ_WIDTH,
NL80211_RATE_INFO_SHORT_GI,
NL80211_RATE_INFO_BITRATE32,
NL80211_RATE_INFO_VHT_MCS,
NL80211_RATE_INFO_VHT_NSS,
NL80211_RATE_INFO_80_MHZ_WIDTH,
NL80211_RATE_INFO_80P80_MHZ_WIDTH,
NL80211_RATE_INFO_160_MHZ_WIDTH,
NL80211_RATE_INFO_10_MHZ_WIDTH,
NL80211_RATE_INFO_5_MHZ_WIDTH,
NL80211_RATE_INFO_HE_MCS,
NL80211_RATE_INFO_HE_NSS,
NL80211_RATE_INFO_HE_GI,
NL80211_RATE_INFO_HE_DCM,
NL80211_RATE_INFO_HE_RU_ALLOC,
NL80211_RATE_INFO_320_MHZ_WIDTH,
NL80211_RATE_INFO_EHT_MCS,
NL80211_RATE_INFO_EHT_NSS,
NL80211_RATE_INFO_EHT_GI,
NL80211_RATE_INFO_EHT_RU_ALLOC,
/* keep last */
__NL80211_RATE_INFO_AFTER_LAST,
NL80211_RATE_INFO_MAX = __NL80211_RATE_INFO_AFTER_LAST - 1
};
/**
* enum nl80211_sta_bss_param - BSS information collected by STA
*
* These attribute types are used with %NL80211_STA_INFO_BSS_PARAM
* when getting information about the bitrate of a station.
*
* @__NL80211_STA_BSS_PARAM_INVALID: attribute number 0 is reserved
* @NL80211_STA_BSS_PARAM_CTS_PROT: whether CTS protection is enabled (flag)
* @NL80211_STA_BSS_PARAM_SHORT_PREAMBLE: whether short preamble is enabled
* (flag)
* @NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME: whether short slot time is enabled
* (flag)
* @NL80211_STA_BSS_PARAM_DTIM_PERIOD: DTIM period for beaconing (u8)
* @NL80211_STA_BSS_PARAM_BEACON_INTERVAL: Beacon interval (u16)
* @NL80211_STA_BSS_PARAM_MAX: highest sta_bss_param number currently defined
* @__NL80211_STA_BSS_PARAM_AFTER_LAST: internal use
*/
enum nl80211_sta_bss_param {
__NL80211_STA_BSS_PARAM_INVALID,
NL80211_STA_BSS_PARAM_CTS_PROT,
NL80211_STA_BSS_PARAM_SHORT_PREAMBLE,
NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME,
NL80211_STA_BSS_PARAM_DTIM_PERIOD,
NL80211_STA_BSS_PARAM_BEACON_INTERVAL,
/* keep last */
__NL80211_STA_BSS_PARAM_AFTER_LAST,
NL80211_STA_BSS_PARAM_MAX = __NL80211_STA_BSS_PARAM_AFTER_LAST - 1
};
/**
* enum nl80211_sta_info - station information
*
* These attribute types are used with %NL80211_ATTR_STA_INFO
* when getting information about a station.
*
* @__NL80211_STA_INFO_INVALID: attribute number 0 is reserved
* @NL80211_STA_INFO_INACTIVE_TIME: time since last activity (u32, msecs)
* @NL80211_STA_INFO_RX_BYTES: total received bytes (MPDU length)
* (u32, from this station)
* @NL80211_STA_INFO_TX_BYTES: total transmitted bytes (MPDU length)
* (u32, to this station)
* @NL80211_STA_INFO_RX_BYTES64: total received bytes (MPDU length)
* (u64, from this station)
* @NL80211_STA_INFO_TX_BYTES64: total transmitted bytes (MPDU length)
* (u64, to this station)
* @NL80211_STA_INFO_SIGNAL: signal strength of last received PPDU (u8, dBm)
* @NL80211_STA_INFO_TX_BITRATE: current unicast tx rate, nested attribute
* containing info as possible, see &enum nl80211_rate_info
* @NL80211_STA_INFO_RX_PACKETS: total received packet (MSDUs and MMPDUs)
* (u32, from this station)
* @NL80211_STA_INFO_TX_PACKETS: total transmitted packets (MSDUs and MMPDUs)
* (u32, to this station)
* @NL80211_STA_INFO_TX_RETRIES: total retries (MPDUs) (u32, to this station)
* @NL80211_STA_INFO_TX_FAILED: total failed packets (MPDUs)
* (u32, to this station)
* @NL80211_STA_INFO_SIGNAL_AVG: signal strength average (u8, dBm)
* @NL80211_STA_INFO_LLID: the station's mesh LLID
* @NL80211_STA_INFO_PLID: the station's mesh PLID
* @NL80211_STA_INFO_PLINK_STATE: peer link state for the station
* (see %enum nl80211_plink_state)
* @NL80211_STA_INFO_RX_BITRATE: last unicast data frame rx rate, nested
* attribute, like NL80211_STA_INFO_TX_BITRATE.
* @NL80211_STA_INFO_BSS_PARAM: current station's view of BSS, nested attribute
* containing info as possible, see &enum nl80211_sta_bss_param
* @NL80211_STA_INFO_CONNECTED_TIME: time since the station is last connected
* @NL80211_STA_INFO_STA_FLAGS: Contains a struct nl80211_sta_flag_update.
* @NL80211_STA_INFO_BEACON_LOSS: count of times beacon loss was detected (u32)
* @NL80211_STA_INFO_T_OFFSET: timing offset with respect to this STA (s64)
* @NL80211_STA_INFO_LOCAL_PM: local mesh STA link-specific power mode
* @NL80211_STA_INFO_PEER_PM: peer mesh STA link-specific power mode
* @NL80211_STA_INFO_NONPEER_PM: neighbor mesh STA power save mode towards
* non-peer STA
* @NL80211_STA_INFO_CHAIN_SIGNAL: per-chain signal strength of last PPDU
* Contains a nested array of signal strength attributes (u8, dBm)
* @NL80211_STA_INFO_CHAIN_SIGNAL_AVG: per-chain signal strength average
* Same format as NL80211_STA_INFO_CHAIN_SIGNAL.
* @NL80211_STA_EXPECTED_THROUGHPUT: expected throughput considering also the
* 802.11 header (u32, kbps)
* @NL80211_STA_INFO_RX_DROP_MISC: RX packets dropped for unspecified reasons
* (u64)
* @NL80211_STA_INFO_BEACON_RX: number of beacons received from this peer (u64)
* @NL80211_STA_INFO_BEACON_SIGNAL_AVG: signal strength average
* for beacons only (u8, dBm)
* @NL80211_STA_INFO_TID_STATS: per-TID statistics (see &enum nl80211_tid_stats)
* This is a nested attribute where each the inner attribute number is the
* TID+1 and the special TID 16 (i.e. value 17) is used for non-QoS frames;
* each one of those is again nested with &enum nl80211_tid_stats
* attributes carrying the actual values.
* @NL80211_STA_INFO_RX_DURATION: aggregate PPDU duration for all frames
* received from the station (u64, usec)
* @NL80211_STA_INFO_PAD: attribute used for padding for 64-bit alignment
* @NL80211_STA_INFO_ACK_SIGNAL: signal strength of the last ACK frame(u8, dBm)
* @NL80211_STA_INFO_ACK_SIGNAL_AVG: avg signal strength of ACK frames (s8, dBm)
* @NL80211_STA_INFO_RX_MPDUS: total number of received packets (MPDUs)
* (u32, from this station)
* @NL80211_STA_INFO_FCS_ERROR_COUNT: total number of packets (MPDUs) received
* with an FCS error (u32, from this station). This count may not include
* some packets with an FCS error due to TA corruption. Hence this counter
* might not be fully accurate.
* @NL80211_STA_INFO_CONNECTED_TO_GATE: set to true if STA has a path to a
* mesh gate (u8, 0 or 1)
* @NL80211_STA_INFO_TX_DURATION: aggregate PPDU duration for all frames
* sent to the station (u64, usec)
* @NL80211_STA_INFO_AIRTIME_WEIGHT: current airtime weight for station (u16)
* @NL80211_STA_INFO_AIRTIME_LINK_METRIC: airtime link metric for mesh station
* @NL80211_STA_INFO_ASSOC_AT_BOOTTIME: Timestamp (CLOCK_BOOTTIME, nanoseconds)
* of STA's association
* @NL80211_STA_INFO_CONNECTED_TO_AS: set to true if STA has a path to a
* authentication server (u8, 0 or 1)
* @__NL80211_STA_INFO_AFTER_LAST: internal
* @NL80211_STA_INFO_MAX: highest possible station info attribute
*/
enum nl80211_sta_info {
__NL80211_STA_INFO_INVALID,
NL80211_STA_INFO_INACTIVE_TIME,
NL80211_STA_INFO_RX_BYTES,
NL80211_STA_INFO_TX_BYTES,
NL80211_STA_INFO_LLID,
NL80211_STA_INFO_PLID,
NL80211_STA_INFO_PLINK_STATE,
NL80211_STA_INFO_SIGNAL,
NL80211_STA_INFO_TX_BITRATE,
NL80211_STA_INFO_RX_PACKETS,
NL80211_STA_INFO_TX_PACKETS,
NL80211_STA_INFO_TX_RETRIES,
NL80211_STA_INFO_TX_FAILED,
NL80211_STA_INFO_SIGNAL_AVG,
NL80211_STA_INFO_RX_BITRATE,
NL80211_STA_INFO_BSS_PARAM,
NL80211_STA_INFO_CONNECTED_TIME,
NL80211_STA_INFO_STA_FLAGS,
NL80211_STA_INFO_BEACON_LOSS,
NL80211_STA_INFO_T_OFFSET,
NL80211_STA_INFO_LOCAL_PM,
NL80211_STA_INFO_PEER_PM,
NL80211_STA_INFO_NONPEER_PM,
NL80211_STA_INFO_RX_BYTES64,
NL80211_STA_INFO_TX_BYTES64,
NL80211_STA_INFO_CHAIN_SIGNAL,
NL80211_STA_INFO_CHAIN_SIGNAL_AVG,
NL80211_STA_INFO_EXPECTED_THROUGHPUT,
NL80211_STA_INFO_RX_DROP_MISC,
NL80211_STA_INFO_BEACON_RX,
NL80211_STA_INFO_BEACON_SIGNAL_AVG,
NL80211_STA_INFO_TID_STATS,
NL80211_STA_INFO_RX_DURATION,
NL80211_STA_INFO_PAD,
NL80211_STA_INFO_ACK_SIGNAL,
NL80211_STA_INFO_ACK_SIGNAL_AVG,
NL80211_STA_INFO_RX_MPDUS,
NL80211_STA_INFO_FCS_ERROR_COUNT,
NL80211_STA_INFO_CONNECTED_TO_GATE,
NL80211_STA_INFO_TX_DURATION,
NL80211_STA_INFO_AIRTIME_WEIGHT,
NL80211_STA_INFO_AIRTIME_LINK_METRIC,
NL80211_STA_INFO_ASSOC_AT_BOOTTIME,
NL80211_STA_INFO_CONNECTED_TO_AS,
/* keep last */
__NL80211_STA_INFO_AFTER_LAST,
NL80211_STA_INFO_MAX = __NL80211_STA_INFO_AFTER_LAST - 1
};
/* we renamed this - stay compatible */
#define NL80211_STA_INFO_DATA_ACK_SIGNAL_AVG NL80211_STA_INFO_ACK_SIGNAL_AVG
/**
* enum nl80211_tid_stats - per TID statistics attributes
* @__NL80211_TID_STATS_INVALID: attribute number 0 is reserved
* @NL80211_TID_STATS_RX_MSDU: number of MSDUs received (u64)
* @NL80211_TID_STATS_TX_MSDU: number of MSDUs transmitted (or
* attempted to transmit; u64)
* @NL80211_TID_STATS_TX_MSDU_RETRIES: number of retries for
* transmitted MSDUs (not counting the first attempt; u64)
* @NL80211_TID_STATS_TX_MSDU_FAILED: number of failed transmitted
* MSDUs (u64)
* @NL80211_TID_STATS_PAD: attribute used for padding for 64-bit alignment
* @NL80211_TID_STATS_TXQ_STATS: TXQ stats (nested attribute)
* @NUM_NL80211_TID_STATS: number of attributes here
* @NL80211_TID_STATS_MAX: highest numbered attribute here
*/
enum nl80211_tid_stats {
__NL80211_TID_STATS_INVALID,
NL80211_TID_STATS_RX_MSDU,
NL80211_TID_STATS_TX_MSDU,
NL80211_TID_STATS_TX_MSDU_RETRIES,
NL80211_TID_STATS_TX_MSDU_FAILED,
NL80211_TID_STATS_PAD,
NL80211_TID_STATS_TXQ_STATS,
/* keep last */
NUM_NL80211_TID_STATS,
NL80211_TID_STATS_MAX = NUM_NL80211_TID_STATS - 1
};
/**
* enum nl80211_txq_stats - per TXQ statistics attributes
* @__NL80211_TXQ_STATS_INVALID: attribute number 0 is reserved
* @NUM_NL80211_TXQ_STATS: number of attributes here
* @NL80211_TXQ_STATS_BACKLOG_BYTES: number of bytes currently backlogged
* @NL80211_TXQ_STATS_BACKLOG_PACKETS: number of packets currently
* backlogged
* @NL80211_TXQ_STATS_FLOWS: total number of new flows seen
* @NL80211_TXQ_STATS_DROPS: total number of packet drops
* @NL80211_TXQ_STATS_ECN_MARKS: total number of packet ECN marks
* @NL80211_TXQ_STATS_OVERLIMIT: number of drops due to queue space overflow
* @NL80211_TXQ_STATS_OVERMEMORY: number of drops due to memory limit overflow
* (only for per-phy stats)
* @NL80211_TXQ_STATS_COLLISIONS: number of hash collisions
* @NL80211_TXQ_STATS_TX_BYTES: total number of bytes dequeued from TXQ
* @NL80211_TXQ_STATS_TX_PACKETS: total number of packets dequeued from TXQ
* @NL80211_TXQ_STATS_MAX_FLOWS: number of flow buckets for PHY
* @NL80211_TXQ_STATS_MAX: highest numbered attribute here
*/
enum nl80211_txq_stats {
__NL80211_TXQ_STATS_INVALID,
NL80211_TXQ_STATS_BACKLOG_BYTES,
NL80211_TXQ_STATS_BACKLOG_PACKETS,
NL80211_TXQ_STATS_FLOWS,
NL80211_TXQ_STATS_DROPS,
NL80211_TXQ_STATS_ECN_MARKS,
NL80211_TXQ_STATS_OVERLIMIT,
NL80211_TXQ_STATS_OVERMEMORY,
NL80211_TXQ_STATS_COLLISIONS,
NL80211_TXQ_STATS_TX_BYTES,
NL80211_TXQ_STATS_TX_PACKETS,
NL80211_TXQ_STATS_MAX_FLOWS,
/* keep last */
NUM_NL80211_TXQ_STATS,
NL80211_TXQ_STATS_MAX = NUM_NL80211_TXQ_STATS - 1
};
/**
* enum nl80211_mpath_flags - nl80211 mesh path flags
*
* @NL80211_MPATH_FLAG_ACTIVE: the mesh path is active
* @NL80211_MPATH_FLAG_RESOLVING: the mesh path discovery process is running
* @NL80211_MPATH_FLAG_SN_VALID: the mesh path contains a valid SN
* @NL80211_MPATH_FLAG_FIXED: the mesh path has been manually set
* @NL80211_MPATH_FLAG_RESOLVED: the mesh path discovery process succeeded
*/
enum nl80211_mpath_flags {
NL80211_MPATH_FLAG_ACTIVE = 1<<0,
NL80211_MPATH_FLAG_RESOLVING = 1<<1,
NL80211_MPATH_FLAG_SN_VALID = 1<<2,
NL80211_MPATH_FLAG_FIXED = 1<<3,
NL80211_MPATH_FLAG_RESOLVED = 1<<4,
};
/**
* enum nl80211_mpath_info - mesh path information
*
* These attribute types are used with %NL80211_ATTR_MPATH_INFO when getting
* information about a mesh path.
*
* @__NL80211_MPATH_INFO_INVALID: attribute number 0 is reserved
* @NL80211_MPATH_INFO_FRAME_QLEN: number of queued frames for this destination
* @NL80211_MPATH_INFO_SN: destination sequence number
* @NL80211_MPATH_INFO_METRIC: metric (cost) of this mesh path
* @NL80211_MPATH_INFO_EXPTIME: expiration time for the path, in msec from now
* @NL80211_MPATH_INFO_FLAGS: mesh path flags, enumerated in
* &enum nl80211_mpath_flags;
* @NL80211_MPATH_INFO_DISCOVERY_TIMEOUT: total path discovery timeout, in msec
* @NL80211_MPATH_INFO_DISCOVERY_RETRIES: mesh path discovery retries
* @NL80211_MPATH_INFO_HOP_COUNT: hop count to destination
* @NL80211_MPATH_INFO_PATH_CHANGE: total number of path changes to destination
* @NL80211_MPATH_INFO_MAX: highest mesh path information attribute number
* currently defined
* @__NL80211_MPATH_INFO_AFTER_LAST: internal use
*/
enum nl80211_mpath_info {
__NL80211_MPATH_INFO_INVALID,
NL80211_MPATH_INFO_FRAME_QLEN,
NL80211_MPATH_INFO_SN,
NL80211_MPATH_INFO_METRIC,
NL80211_MPATH_INFO_EXPTIME,
NL80211_MPATH_INFO_FLAGS,
NL80211_MPATH_INFO_DISCOVERY_TIMEOUT,
NL80211_MPATH_INFO_DISCOVERY_RETRIES,
NL80211_MPATH_INFO_HOP_COUNT,
NL80211_MPATH_INFO_PATH_CHANGE,
/* keep last */
__NL80211_MPATH_INFO_AFTER_LAST,
NL80211_MPATH_INFO_MAX = __NL80211_MPATH_INFO_AFTER_LAST - 1
};
/**
* enum nl80211_band_iftype_attr - Interface type data attributes
*
* @__NL80211_BAND_IFTYPE_ATTR_INVALID: attribute number 0 is reserved
* @NL80211_BAND_IFTYPE_ATTR_IFTYPES: nested attribute containing a flag attribute
* for each interface type that supports the band data
* @NL80211_BAND_IFTYPE_ATTR_HE_CAP_MAC: HE MAC capabilities as in HE
* capabilities IE
* @NL80211_BAND_IFTYPE_ATTR_HE_CAP_PHY: HE PHY capabilities as in HE
* capabilities IE
* @NL80211_BAND_IFTYPE_ATTR_HE_CAP_MCS_SET: HE supported NSS/MCS as in HE
* capabilities IE
* @NL80211_BAND_IFTYPE_ATTR_HE_CAP_PPE: HE PPE thresholds information as
* defined in HE capabilities IE
* @NL80211_BAND_IFTYPE_ATTR_HE_6GHZ_CAPA: HE 6GHz band capabilities (__le16),
* given for all 6 GHz band channels
* @NL80211_BAND_IFTYPE_ATTR_VENDOR_ELEMS: vendor element capabilities that are
* advertised on this band/for this iftype (binary)
* @NL80211_BAND_IFTYPE_ATTR_EHT_CAP_MAC: EHT MAC capabilities as in EHT
* capabilities element
* @NL80211_BAND_IFTYPE_ATTR_EHT_CAP_PHY: EHT PHY capabilities as in EHT
* capabilities element
* @NL80211_BAND_IFTYPE_ATTR_EHT_CAP_MCS_SET: EHT supported NSS/MCS as in EHT
* capabilities element
* @NL80211_BAND_IFTYPE_ATTR_EHT_CAP_PPE: EHT PPE thresholds information as
* defined in EHT capabilities element
* @__NL80211_BAND_IFTYPE_ATTR_AFTER_LAST: internal use
* @NL80211_BAND_IFTYPE_ATTR_MAX: highest band attribute currently defined
*/
enum nl80211_band_iftype_attr {
__NL80211_BAND_IFTYPE_ATTR_INVALID,
NL80211_BAND_IFTYPE_ATTR_IFTYPES,
NL80211_BAND_IFTYPE_ATTR_HE_CAP_MAC,
NL80211_BAND_IFTYPE_ATTR_HE_CAP_PHY,
NL80211_BAND_IFTYPE_ATTR_HE_CAP_MCS_SET,
NL80211_BAND_IFTYPE_ATTR_HE_CAP_PPE,
NL80211_BAND_IFTYPE_ATTR_HE_6GHZ_CAPA,
NL80211_BAND_IFTYPE_ATTR_VENDOR_ELEMS,
NL80211_BAND_IFTYPE_ATTR_EHT_CAP_MAC,
NL80211_BAND_IFTYPE_ATTR_EHT_CAP_PHY,
NL80211_BAND_IFTYPE_ATTR_EHT_CAP_MCS_SET,
NL80211_BAND_IFTYPE_ATTR_EHT_CAP_PPE,
/* keep last */
__NL80211_BAND_IFTYPE_ATTR_AFTER_LAST,
NL80211_BAND_IFTYPE_ATTR_MAX = __NL80211_BAND_IFTYPE_ATTR_AFTER_LAST - 1
};
/**
* enum nl80211_band_attr - band attributes
* @__NL80211_BAND_ATTR_INVALID: attribute number 0 is reserved
* @NL80211_BAND_ATTR_FREQS: supported frequencies in this band,
* an array of nested frequency attributes
* @NL80211_BAND_ATTR_RATES: supported bitrates in this band,
* an array of nested bitrate attributes
* @NL80211_BAND_ATTR_HT_MCS_SET: 16-byte attribute containing the MCS set as
* defined in 802.11n
* @NL80211_BAND_ATTR_HT_CAPA: HT capabilities, as in the HT information IE
* @NL80211_BAND_ATTR_HT_AMPDU_FACTOR: A-MPDU factor, as in 11n
* @NL80211_BAND_ATTR_HT_AMPDU_DENSITY: A-MPDU density, as in 11n
* @NL80211_BAND_ATTR_VHT_MCS_SET: 32-byte attribute containing the MCS set as
* defined in 802.11ac
* @NL80211_BAND_ATTR_VHT_CAPA: VHT capabilities, as in the HT information IE
* @NL80211_BAND_ATTR_IFTYPE_DATA: nested array attribute, with each entry using
* attributes from &enum nl80211_band_iftype_attr
* @NL80211_BAND_ATTR_EDMG_CHANNELS: bitmap that indicates the 2.16 GHz
* channel(s) that are allowed to be used for EDMG transmissions.
* Defined by IEEE P802.11ay/D4.0 section 9.4.2.251.
* @NL80211_BAND_ATTR_EDMG_BW_CONFIG: Channel BW Configuration subfield encodes
* the allowed channel bandwidth configurations.
* Defined by IEEE P802.11ay/D4.0 section 9.4.2.251, Table 13.
* @NL80211_BAND_ATTR_S1G_MCS_NSS_SET: S1G capabilities, supported S1G-MCS and NSS
* set subfield, as in the S1G information IE, 5 bytes
* @NL80211_BAND_ATTR_S1G_CAPA: S1G capabilities information subfield as in the
* S1G information IE, 10 bytes
* @NL80211_BAND_ATTR_MAX: highest band attribute currently defined
* @__NL80211_BAND_ATTR_AFTER_LAST: internal use
*/
enum nl80211_band_attr {
__NL80211_BAND_ATTR_INVALID,
NL80211_BAND_ATTR_FREQS,
NL80211_BAND_ATTR_RATES,
NL80211_BAND_ATTR_HT_MCS_SET,
NL80211_BAND_ATTR_HT_CAPA,
NL80211_BAND_ATTR_HT_AMPDU_FACTOR,
NL80211_BAND_ATTR_HT_AMPDU_DENSITY,
NL80211_BAND_ATTR_VHT_MCS_SET,
NL80211_BAND_ATTR_VHT_CAPA,
NL80211_BAND_ATTR_IFTYPE_DATA,
NL80211_BAND_ATTR_EDMG_CHANNELS,
NL80211_BAND_ATTR_EDMG_BW_CONFIG,
NL80211_BAND_ATTR_S1G_MCS_NSS_SET,
NL80211_BAND_ATTR_S1G_CAPA,
/* keep last */
__NL80211_BAND_ATTR_AFTER_LAST,
NL80211_BAND_ATTR_MAX = __NL80211_BAND_ATTR_AFTER_LAST - 1
};
#define NL80211_BAND_ATTR_HT_CAPA NL80211_BAND_ATTR_HT_CAPA
/**
* enum nl80211_wmm_rule - regulatory wmm rule
*
* @__NL80211_WMMR_INVALID: attribute number 0 is reserved
* @NL80211_WMMR_CW_MIN: Minimum contention window slot.
* @NL80211_WMMR_CW_MAX: Maximum contention window slot.
* @NL80211_WMMR_AIFSN: Arbitration Inter Frame Space.
* @NL80211_WMMR_TXOP: Maximum allowed tx operation time.
* @nl80211_WMMR_MAX: highest possible wmm rule.
* @__NL80211_WMMR_LAST: Internal use.
*/
enum nl80211_wmm_rule {
__NL80211_WMMR_INVALID,
NL80211_WMMR_CW_MIN,
NL80211_WMMR_CW_MAX,
NL80211_WMMR_AIFSN,
NL80211_WMMR_TXOP,
/* keep last */
__NL80211_WMMR_LAST,
NL80211_WMMR_MAX = __NL80211_WMMR_LAST - 1
};
/**
* enum nl80211_frequency_attr - frequency attributes
* @__NL80211_FREQUENCY_ATTR_INVALID: attribute number 0 is reserved
* @NL80211_FREQUENCY_ATTR_FREQ: Frequency in MHz
* @NL80211_FREQUENCY_ATTR_DISABLED: Channel is disabled in current
* regulatory domain.
* @NL80211_FREQUENCY_ATTR_NO_IR: no mechanisms that initiate radiation
* are permitted on this channel, this includes sending probe
* requests, or modes of operation that require beaconing.
* @NL80211_FREQUENCY_ATTR_RADAR: Radar detection is mandatory
* on this channel in current regulatory domain.
* @NL80211_FREQUENCY_ATTR_MAX_TX_POWER: Maximum transmission power in mBm
* (100 * dBm).
* @NL80211_FREQUENCY_ATTR_DFS_STATE: current state for DFS
* (enum nl80211_dfs_state)
* @NL80211_FREQUENCY_ATTR_DFS_TIME: time in miliseconds for how long
* this channel is in this DFS state.
* @NL80211_FREQUENCY_ATTR_NO_HT40_MINUS: HT40- isn't possible with this
* channel as the control channel
* @NL80211_FREQUENCY_ATTR_NO_HT40_PLUS: HT40+ isn't possible with this
* channel as the control channel
* @NL80211_FREQUENCY_ATTR_NO_80MHZ: any 80 MHz channel using this channel
* as the primary or any of the secondary channels isn't possible,
* this includes 80+80 channels
* @NL80211_FREQUENCY_ATTR_NO_160MHZ: any 160 MHz (but not 80+80) channel
* using this channel as the primary or any of the secondary channels
* isn't possible
* @NL80211_FREQUENCY_ATTR_DFS_CAC_TIME: DFS CAC time in milliseconds.
* @NL80211_FREQUENCY_ATTR_INDOOR_ONLY: Only indoor use is permitted on this
* channel. A channel that has the INDOOR_ONLY attribute can only be
* used when there is a clear assessment that the device is operating in
* an indoor surroundings, i.e., it is connected to AC power (and not
* through portable DC inverters) or is under the control of a master
* that is acting as an AP and is connected to AC power.
* @NL80211_FREQUENCY_ATTR_IR_CONCURRENT: IR operation is allowed on this
* channel if it's connected concurrently to a BSS on the same channel on
* the 2 GHz band or to a channel in the same UNII band (on the 5 GHz
* band), and IEEE80211_CHAN_RADAR is not set. Instantiating a GO or TDLS
* off-channel on a channel that has the IR_CONCURRENT attribute set can be
* done when there is a clear assessment that the device is operating under
* the guidance of an authorized master, i.e., setting up a GO or TDLS
* off-channel while the device is also connected to an AP with DFS and
* radar detection on the UNII band (it is up to user-space, i.e.,
* wpa_supplicant to perform the required verifications). Using this
* attribute for IR is disallowed for master interfaces (IBSS, AP).
* @NL80211_FREQUENCY_ATTR_NO_20MHZ: 20 MHz operation is not allowed
* on this channel in current regulatory domain.
* @NL80211_FREQUENCY_ATTR_NO_10MHZ: 10 MHz operation is not allowed
* on this channel in current regulatory domain.
* @NL80211_FREQUENCY_ATTR_WMM: this channel has wmm limitations.
* This is a nested attribute that contains the wmm limitation per AC.
* (see &enum nl80211_wmm_rule)
* @NL80211_FREQUENCY_ATTR_NO_HE: HE operation is not allowed on this channel
* in current regulatory domain.
* @NL80211_FREQUENCY_ATTR_OFFSET: frequency offset in KHz
* @NL80211_FREQUENCY_ATTR_1MHZ: 1 MHz operation is allowed
* on this channel in current regulatory domain.
* @NL80211_FREQUENCY_ATTR_2MHZ: 2 MHz operation is allowed
* on this channel in current regulatory domain.
* @NL80211_FREQUENCY_ATTR_4MHZ: 4 MHz operation is allowed
* on this channel in current regulatory domain.
* @NL80211_FREQUENCY_ATTR_8MHZ: 8 MHz operation is allowed
* on this channel in current regulatory domain.
* @NL80211_FREQUENCY_ATTR_16MHZ: 16 MHz operation is allowed
* on this channel in current regulatory domain.
* @NL80211_FREQUENCY_ATTR_NO_320MHZ: any 320 MHz channel using this channel
* as the primary or any of the secondary channels isn't possible
* @NL80211_FREQUENCY_ATTR_NO_EHT: EHT operation is not allowed on this channel
* in current regulatory domain.
* @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number
* currently defined
* @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use
*
* See https://apps.fcc.gov/eas/comments/GetPublishedDocument.html?id=327&tn=528122
* for more information on the FCC description of the relaxations allowed
* by NL80211_FREQUENCY_ATTR_INDOOR_ONLY and
* NL80211_FREQUENCY_ATTR_IR_CONCURRENT.
*/
enum nl80211_frequency_attr {
__NL80211_FREQUENCY_ATTR_INVALID,
NL80211_FREQUENCY_ATTR_FREQ,
NL80211_FREQUENCY_ATTR_DISABLED,
NL80211_FREQUENCY_ATTR_NO_IR,
__NL80211_FREQUENCY_ATTR_NO_IBSS,
NL80211_FREQUENCY_ATTR_RADAR,
NL80211_FREQUENCY_ATTR_MAX_TX_POWER,
NL80211_FREQUENCY_ATTR_DFS_STATE,
NL80211_FREQUENCY_ATTR_DFS_TIME,
NL80211_FREQUENCY_ATTR_NO_HT40_MINUS,
NL80211_FREQUENCY_ATTR_NO_HT40_PLUS,
NL80211_FREQUENCY_ATTR_NO_80MHZ,
NL80211_FREQUENCY_ATTR_NO_160MHZ,
NL80211_FREQUENCY_ATTR_DFS_CAC_TIME,
NL80211_FREQUENCY_ATTR_INDOOR_ONLY,
NL80211_FREQUENCY_ATTR_IR_CONCURRENT,
NL80211_FREQUENCY_ATTR_NO_20MHZ,
NL80211_FREQUENCY_ATTR_NO_10MHZ,
NL80211_FREQUENCY_ATTR_WMM,
NL80211_FREQUENCY_ATTR_NO_HE,
NL80211_FREQUENCY_ATTR_OFFSET,
NL80211_FREQUENCY_ATTR_1MHZ,
NL80211_FREQUENCY_ATTR_2MHZ,
NL80211_FREQUENCY_ATTR_4MHZ,
NL80211_FREQUENCY_ATTR_8MHZ,
NL80211_FREQUENCY_ATTR_16MHZ,
NL80211_FREQUENCY_ATTR_NO_320MHZ,
NL80211_FREQUENCY_ATTR_NO_EHT,
/* keep last */
__NL80211_FREQUENCY_ATTR_AFTER_LAST,
NL80211_FREQUENCY_ATTR_MAX = __NL80211_FREQUENCY_ATTR_AFTER_LAST - 1
};
#define NL80211_FREQUENCY_ATTR_MAX_TX_POWER NL80211_FREQUENCY_ATTR_MAX_TX_POWER
#define NL80211_FREQUENCY_ATTR_PASSIVE_SCAN NL80211_FREQUENCY_ATTR_NO_IR
#define NL80211_FREQUENCY_ATTR_NO_IBSS NL80211_FREQUENCY_ATTR_NO_IR
#define NL80211_FREQUENCY_ATTR_NO_IR NL80211_FREQUENCY_ATTR_NO_IR
#define NL80211_FREQUENCY_ATTR_GO_CONCURRENT \
NL80211_FREQUENCY_ATTR_IR_CONCURRENT
/**
* enum nl80211_bitrate_attr - bitrate attributes
* @__NL80211_BITRATE_ATTR_INVALID: attribute number 0 is reserved
* @NL80211_BITRATE_ATTR_RATE: Bitrate in units of 100 kbps
* @NL80211_BITRATE_ATTR_2GHZ_SHORTPREAMBLE: Short preamble supported
* in 2.4 GHz band.
* @NL80211_BITRATE_ATTR_MAX: highest bitrate attribute number
* currently defined
* @__NL80211_BITRATE_ATTR_AFTER_LAST: internal use
*/
enum nl80211_bitrate_attr {
__NL80211_BITRATE_ATTR_INVALID,
NL80211_BITRATE_ATTR_RATE,
NL80211_BITRATE_ATTR_2GHZ_SHORTPREAMBLE,
/* keep last */
__NL80211_BITRATE_ATTR_AFTER_LAST,
NL80211_BITRATE_ATTR_MAX = __NL80211_BITRATE_ATTR_AFTER_LAST - 1
};
/**
* enum nl80211_initiator - Indicates the initiator of a reg domain request
* @NL80211_REGDOM_SET_BY_CORE: Core queried CRDA for a dynamic world
* regulatory domain.
* @NL80211_REGDOM_SET_BY_USER: User asked the wireless core to set the
* regulatory domain.
* @NL80211_REGDOM_SET_BY_DRIVER: a wireless drivers has hinted to the
* wireless core it thinks its knows the regulatory domain we should be in.
* @NL80211_REGDOM_SET_BY_COUNTRY_IE: the wireless core has received an
* 802.11 country information element with regulatory information it
* thinks we should consider. cfg80211 only processes the country
* code from the IE, and relies on the regulatory domain information
* structure passed by userspace (CRDA) from our wireless-regdb.
* If a channel is enabled but the country code indicates it should
* be disabled we disable the channel and re-enable it upon disassociation.
*/
enum nl80211_reg_initiator {
NL80211_REGDOM_SET_BY_CORE,
NL80211_REGDOM_SET_BY_USER,
NL80211_REGDOM_SET_BY_DRIVER,
NL80211_REGDOM_SET_BY_COUNTRY_IE,
};
/**
* enum nl80211_reg_type - specifies the type of regulatory domain
* @NL80211_REGDOM_TYPE_COUNTRY: the regulatory domain set is one that pertains
* to a specific country. When this is set you can count on the
* ISO / IEC 3166 alpha2 country code being valid.
* @NL80211_REGDOM_TYPE_WORLD: the regulatory set domain is the world regulatory
* domain.
* @NL80211_REGDOM_TYPE_CUSTOM_WORLD: the regulatory domain set is a custom
* driver specific world regulatory domain. These do not apply system-wide
* and are only applicable to the individual devices which have requested
* them to be applied.
* @NL80211_REGDOM_TYPE_INTERSECTION: the regulatory domain set is the product
* of an intersection between two regulatory domains -- the previously
* set regulatory domain on the system and the last accepted regulatory
* domain request to be processed.
*/
enum nl80211_reg_type {
NL80211_REGDOM_TYPE_COUNTRY,
NL80211_REGDOM_TYPE_WORLD,
NL80211_REGDOM_TYPE_CUSTOM_WORLD,
NL80211_REGDOM_TYPE_INTERSECTION,
};
/**
* enum nl80211_reg_rule_attr - regulatory rule attributes
* @__NL80211_REG_RULE_ATTR_INVALID: attribute number 0 is reserved
* @NL80211_ATTR_REG_RULE_FLAGS: a set of flags which specify additional
* considerations for a given frequency range. These are the
* &enum nl80211_reg_rule_flags.
* @NL80211_ATTR_FREQ_RANGE_START: starting frequencry for the regulatory
* rule in KHz. This is not a center of frequency but an actual regulatory
* band edge.
* @NL80211_ATTR_FREQ_RANGE_END: ending frequency for the regulatory rule
* in KHz. This is not a center a frequency but an actual regulatory
* band edge.
* @NL80211_ATTR_FREQ_RANGE_MAX_BW: maximum allowed bandwidth for this
* frequency range, in KHz.
* @NL80211_ATTR_POWER_RULE_MAX_ANT_GAIN: the maximum allowed antenna gain
* for a given frequency range. The value is in mBi (100 * dBi).
* If you don't have one then don't send this.
* @NL80211_ATTR_POWER_RULE_MAX_EIRP: the maximum allowed EIRP for
* a given frequency range. The value is in mBm (100 * dBm).
* @NL80211_ATTR_DFS_CAC_TIME: DFS CAC time in milliseconds.
* If not present or 0 default CAC time will be used.
* @NL80211_REG_RULE_ATTR_MAX: highest regulatory rule attribute number
* currently defined
* @__NL80211_REG_RULE_ATTR_AFTER_LAST: internal use
*/
enum nl80211_reg_rule_attr {
__NL80211_REG_RULE_ATTR_INVALID,
NL80211_ATTR_REG_RULE_FLAGS,
NL80211_ATTR_FREQ_RANGE_START,
NL80211_ATTR_FREQ_RANGE_END,
NL80211_ATTR_FREQ_RANGE_MAX_BW,
NL80211_ATTR_POWER_RULE_MAX_ANT_GAIN,
NL80211_ATTR_POWER_RULE_MAX_EIRP,
NL80211_ATTR_DFS_CAC_TIME,
/* keep last */
__NL80211_REG_RULE_ATTR_AFTER_LAST,
NL80211_REG_RULE_ATTR_MAX = __NL80211_REG_RULE_ATTR_AFTER_LAST - 1
};
/**
* enum nl80211_sched_scan_match_attr - scheduled scan match attributes
* @__NL80211_SCHED_SCAN_MATCH_ATTR_INVALID: attribute number 0 is reserved
* @NL80211_SCHED_SCAN_MATCH_ATTR_SSID: SSID to be used for matching,
* only report BSS with matching SSID.
* (This cannot be used together with BSSID.)
* @NL80211_SCHED_SCAN_MATCH_ATTR_RSSI: RSSI threshold (in dBm) for reporting a
* BSS in scan results. Filtering is turned off if not specified. Note that
* if this attribute is in a match set of its own, then it is treated as
* the default value for all matchsets with an SSID, rather than being a
* matchset of its own without an RSSI filter. This is due to problems with
* how this API was implemented in the past. Also, due to the same problem,
* the only way to create a matchset with only an RSSI filter (with this
* attribute) is if there's only a single matchset with the RSSI attribute.
* @NL80211_SCHED_SCAN_MATCH_ATTR_RELATIVE_RSSI: Flag indicating whether
* %NL80211_SCHED_SCAN_MATCH_ATTR_RSSI to be used as absolute RSSI or
* relative to current bss's RSSI.
* @NL80211_SCHED_SCAN_MATCH_ATTR_RSSI_ADJUST: When present the RSSI level for
* BSS-es in the specified band is to be adjusted before doing
* RSSI-based BSS selection. The attribute value is a packed structure
* value as specified by &struct nl80211_bss_select_rssi_adjust.
* @NL80211_SCHED_SCAN_MATCH_ATTR_BSSID: BSSID to be used for matching
* (this cannot be used together with SSID).
* @NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI: Nested attribute that carries the
* band specific minimum rssi thresholds for the bands defined in
* enum nl80211_band. The minimum rssi threshold value(s32) specific to a
* band shall be encapsulated in attribute with type value equals to one
* of the NL80211_BAND_* defined in enum nl80211_band. For example, the
* minimum rssi threshold value for 2.4GHZ band shall be encapsulated
* within an attribute of type NL80211_BAND_2GHZ. And one or more of such
* attributes will be nested within this attribute.
* @NL80211_SCHED_SCAN_MATCH_ATTR_MAX: highest scheduled scan filter
* attribute number currently defined
* @__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST: internal use
*/
enum nl80211_sched_scan_match_attr {
__NL80211_SCHED_SCAN_MATCH_ATTR_INVALID,
NL80211_SCHED_SCAN_MATCH_ATTR_SSID,
NL80211_SCHED_SCAN_MATCH_ATTR_RSSI,
NL80211_SCHED_SCAN_MATCH_ATTR_RELATIVE_RSSI,
NL80211_SCHED_SCAN_MATCH_ATTR_RSSI_ADJUST,
NL80211_SCHED_SCAN_MATCH_ATTR_BSSID,
NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI,
/* keep last */
__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST,
NL80211_SCHED_SCAN_MATCH_ATTR_MAX =
__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST - 1
};
/* only for backward compatibility */
#define NL80211_ATTR_SCHED_SCAN_MATCH_SSID NL80211_SCHED_SCAN_MATCH_ATTR_SSID
/**
* enum nl80211_reg_rule_flags - regulatory rule flags
*
* @NL80211_RRF_NO_OFDM: OFDM modulation not allowed
* @NL80211_RRF_NO_CCK: CCK modulation not allowed
* @NL80211_RRF_NO_INDOOR: indoor operation not allowed
* @NL80211_RRF_NO_OUTDOOR: outdoor operation not allowed
* @NL80211_RRF_DFS: DFS support is required to be used
* @NL80211_RRF_PTP_ONLY: this is only for Point To Point links
* @NL80211_RRF_PTMP_ONLY: this is only for Point To Multi Point links
* @NL80211_RRF_NO_IR: no mechanisms that initiate radiation are allowed,
* this includes probe requests or modes of operation that require
* beaconing.
* @NL80211_RRF_AUTO_BW: maximum available bandwidth should be calculated
* base on contiguous rules and wider channels will be allowed to cross
* multiple contiguous/overlapping frequency ranges.
* @NL80211_RRF_IR_CONCURRENT: See %NL80211_FREQUENCY_ATTR_IR_CONCURRENT
* @NL80211_RRF_NO_HT40MINUS: channels can't be used in HT40- operation
* @NL80211_RRF_NO_HT40PLUS: channels can't be used in HT40+ operation
* @NL80211_RRF_NO_80MHZ: 80MHz operation not allowed
* @NL80211_RRF_NO_160MHZ: 160MHz operation not allowed
* @NL80211_RRF_NO_HE: HE operation not allowed
* @NL80211_RRF_NO_320MHZ: 320MHz operation not allowed
*/
enum nl80211_reg_rule_flags {
NL80211_RRF_NO_OFDM = 1<<0,
NL80211_RRF_NO_CCK = 1<<1,
NL80211_RRF_NO_INDOOR = 1<<2,
NL80211_RRF_NO_OUTDOOR = 1<<3,
NL80211_RRF_DFS = 1<<4,
NL80211_RRF_PTP_ONLY = 1<<5,
NL80211_RRF_PTMP_ONLY = 1<<6,
NL80211_RRF_NO_IR = 1<<7,
__NL80211_RRF_NO_IBSS = 1<<8,
NL80211_RRF_AUTO_BW = 1<<11,
NL80211_RRF_IR_CONCURRENT = 1<<12,
NL80211_RRF_NO_HT40MINUS = 1<<13,
NL80211_RRF_NO_HT40PLUS = 1<<14,
NL80211_RRF_NO_80MHZ = 1<<15,
NL80211_RRF_NO_160MHZ = 1<<16,
NL80211_RRF_NO_HE = 1<<17,
NL80211_RRF_NO_320MHZ = 1<<18,
};
#define NL80211_RRF_PASSIVE_SCAN NL80211_RRF_NO_IR
#define NL80211_RRF_NO_IBSS NL80211_RRF_NO_IR
#define NL80211_RRF_NO_IR NL80211_RRF_NO_IR
#define NL80211_RRF_NO_HT40 (NL80211_RRF_NO_HT40MINUS |\
NL80211_RRF_NO_HT40PLUS)
#define NL80211_RRF_GO_CONCURRENT NL80211_RRF_IR_CONCURRENT
/* For backport compatibility with older userspace */
#define NL80211_RRF_NO_IR_ALL (NL80211_RRF_NO_IR | __NL80211_RRF_NO_IBSS)
/**
* enum nl80211_dfs_regions - regulatory DFS regions
*
* @NL80211_DFS_UNSET: Country has no DFS master region specified
* @NL80211_DFS_FCC: Country follows DFS master rules from FCC
* @NL80211_DFS_ETSI: Country follows DFS master rules from ETSI
* @NL80211_DFS_JP: Country follows DFS master rules from JP/MKK/Telec
*/
enum nl80211_dfs_regions {
NL80211_DFS_UNSET = 0,
NL80211_DFS_FCC = 1,
NL80211_DFS_ETSI = 2,
NL80211_DFS_JP = 3,
};
/**
* enum nl80211_user_reg_hint_type - type of user regulatory hint
*
* @NL80211_USER_REG_HINT_USER: a user sent the hint. This is always
* assumed if the attribute is not set.
* @NL80211_USER_REG_HINT_CELL_BASE: the hint comes from a cellular
* base station. Device drivers that have been tested to work
* properly to support this type of hint can enable these hints
* by setting the NL80211_FEATURE_CELL_BASE_REG_HINTS feature
* capability on the struct wiphy. The wireless core will
* ignore all cell base station hints until at least one device
* present has been registered with the wireless core that
* has listed NL80211_FEATURE_CELL_BASE_REG_HINTS as a
* supported feature.
* @NL80211_USER_REG_HINT_INDOOR: a user sent an hint indicating that the
* platform is operating in an indoor environment.
*/
enum nl80211_user_reg_hint_type {
NL80211_USER_REG_HINT_USER = 0,
NL80211_USER_REG_HINT_CELL_BASE = 1,
NL80211_USER_REG_HINT_INDOOR = 2,
};
/**
* enum nl80211_survey_info - survey information
*
* These attribute types are used with %NL80211_ATTR_SURVEY_INFO
* when getting information about a survey.
*
* @__NL80211_SURVEY_INFO_INVALID: attribute number 0 is reserved
* @NL80211_SURVEY_INFO_FREQUENCY: center frequency of channel
* @NL80211_SURVEY_INFO_NOISE: noise level of channel (u8, dBm)
* @NL80211_SURVEY_INFO_IN_USE: channel is currently being used
* @NL80211_SURVEY_INFO_TIME: amount of time (in ms) that the radio
* was turned on (on channel or globally)
* @NL80211_SURVEY_INFO_TIME_BUSY: amount of the time the primary
* channel was sensed busy (either due to activity or energy detect)
* @NL80211_SURVEY_INFO_TIME_EXT_BUSY: amount of time the extension
* channel was sensed busy
* @NL80211_SURVEY_INFO_TIME_RX: amount of time the radio spent
* receiving data (on channel or globally)
* @NL80211_SURVEY_INFO_TIME_TX: amount of time the radio spent
* transmitting data (on channel or globally)
* @NL80211_SURVEY_INFO_TIME_SCAN: time the radio spent for scan
* (on this channel or globally)
* @NL80211_SURVEY_INFO_PAD: attribute used for padding for 64-bit alignment
* @NL80211_SURVEY_INFO_TIME_BSS_RX: amount of time the radio spent
* receiving frames destined to the local BSS
* @NL80211_SURVEY_INFO_MAX: highest survey info attribute number
* currently defined
* @NL80211_SURVEY_INFO_FREQUENCY_OFFSET: center frequency offset in KHz
* @__NL80211_SURVEY_INFO_AFTER_LAST: internal use
*/
enum nl80211_survey_info {
__NL80211_SURVEY_INFO_INVALID,
NL80211_SURVEY_INFO_FREQUENCY,
NL80211_SURVEY_INFO_NOISE,
NL80211_SURVEY_INFO_IN_USE,
NL80211_SURVEY_INFO_TIME,
NL80211_SURVEY_INFO_TIME_BUSY,
NL80211_SURVEY_INFO_TIME_EXT_BUSY,
NL80211_SURVEY_INFO_TIME_RX,
NL80211_SURVEY_INFO_TIME_TX,
NL80211_SURVEY_INFO_TIME_SCAN,
NL80211_SURVEY_INFO_PAD,
NL80211_SURVEY_INFO_TIME_BSS_RX,
NL80211_SURVEY_INFO_FREQUENCY_OFFSET,
/* keep last */
__NL80211_SURVEY_INFO_AFTER_LAST,
NL80211_SURVEY_INFO_MAX = __NL80211_SURVEY_INFO_AFTER_LAST - 1
};
/* keep old names for compatibility */
#define NL80211_SURVEY_INFO_CHANNEL_TIME NL80211_SURVEY_INFO_TIME
#define NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY NL80211_SURVEY_INFO_TIME_BUSY
#define NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY NL80211_SURVEY_INFO_TIME_EXT_BUSY
#define NL80211_SURVEY_INFO_CHANNEL_TIME_RX NL80211_SURVEY_INFO_TIME_RX
#define NL80211_SURVEY_INFO_CHANNEL_TIME_TX NL80211_SURVEY_INFO_TIME_TX
/**
* enum nl80211_mntr_flags - monitor configuration flags
*
* Monitor configuration flags.
*
* @__NL80211_MNTR_FLAG_INVALID: reserved
*
* @NL80211_MNTR_FLAG_FCSFAIL: pass frames with bad FCS
* @NL80211_MNTR_FLAG_PLCPFAIL: pass frames with bad PLCP
* @NL80211_MNTR_FLAG_CONTROL: pass control frames
* @NL80211_MNTR_FLAG_OTHER_BSS: disable BSSID filtering
* @NL80211_MNTR_FLAG_COOK_FRAMES: report frames after processing.
* overrides all other flags.
* @NL80211_MNTR_FLAG_ACTIVE: use the configured MAC address
* and ACK incoming unicast packets.
*
* @__NL80211_MNTR_FLAG_AFTER_LAST: internal use
* @NL80211_MNTR_FLAG_MAX: highest possible monitor flag
*/
enum nl80211_mntr_flags {
__NL80211_MNTR_FLAG_INVALID,
NL80211_MNTR_FLAG_FCSFAIL,
NL80211_MNTR_FLAG_PLCPFAIL,
NL80211_MNTR_FLAG_CONTROL,
NL80211_MNTR_FLAG_OTHER_BSS,
NL80211_MNTR_FLAG_COOK_FRAMES,
NL80211_MNTR_FLAG_ACTIVE,
/* keep last */
__NL80211_MNTR_FLAG_AFTER_LAST,
NL80211_MNTR_FLAG_MAX = __NL80211_MNTR_FLAG_AFTER_LAST - 1
};
/**
* enum nl80211_mesh_power_mode - mesh power save modes
*
* @NL80211_MESH_POWER_UNKNOWN: The mesh power mode of the mesh STA is
* not known or has not been set yet.
* @NL80211_MESH_POWER_ACTIVE: Active mesh power mode. The mesh STA is
* in Awake state all the time.
* @NL80211_MESH_POWER_LIGHT_SLEEP: Light sleep mode. The mesh STA will
* alternate between Active and Doze states, but will wake up for
* neighbor's beacons.
* @NL80211_MESH_POWER_DEEP_SLEEP: Deep sleep mode. The mesh STA will
* alternate between Active and Doze states, but may not wake up
* for neighbor's beacons.
*
* @__NL80211_MESH_POWER_AFTER_LAST - internal use
* @NL80211_MESH_POWER_MAX - highest possible power save level
*/
enum nl80211_mesh_power_mode {
NL80211_MESH_POWER_UNKNOWN,
NL80211_MESH_POWER_ACTIVE,
NL80211_MESH_POWER_LIGHT_SLEEP,
NL80211_MESH_POWER_DEEP_SLEEP,
__NL80211_MESH_POWER_AFTER_LAST,
NL80211_MESH_POWER_MAX = __NL80211_MESH_POWER_AFTER_LAST - 1
};
/**
* enum nl80211_meshconf_params - mesh configuration parameters
*
* Mesh configuration parameters. These can be changed while the mesh is
* active.
*
* @__NL80211_MESHCONF_INVALID: internal use
*
* @NL80211_MESHCONF_RETRY_TIMEOUT: specifies the initial retry timeout in
* millisecond units, used by the Peer Link Open message
*
* @NL80211_MESHCONF_CONFIRM_TIMEOUT: specifies the initial confirm timeout, in
* millisecond units, used by the peer link management to close a peer link
*
* @NL80211_MESHCONF_HOLDING_TIMEOUT: specifies the holding timeout, in
* millisecond units
*
* @NL80211_MESHCONF_MAX_PEER_LINKS: maximum number of peer links allowed
* on this mesh interface
*
* @NL80211_MESHCONF_MAX_RETRIES: specifies the maximum number of peer link
* open retries that can be sent to establish a new peer link instance in a
* mesh
*
* @NL80211_MESHCONF_TTL: specifies the value of TTL field set at a source mesh
* point.
*
* @NL80211_MESHCONF_AUTO_OPEN_PLINKS: whether we should automatically open
* peer links when we detect compatible mesh peers. Disabled if
* @NL80211_MESH_SETUP_USERSPACE_MPM or @NL80211_MESH_SETUP_USERSPACE_AMPE are
* set.
*
* @NL80211_MESHCONF_HWMP_MAX_PREQ_RETRIES: the number of action frames
* containing a PREQ that an MP can send to a particular destination (path
* target)
*
* @NL80211_MESHCONF_PATH_REFRESH_TIME: how frequently to refresh mesh paths
* (in milliseconds)
*
* @NL80211_MESHCONF_MIN_DISCOVERY_TIMEOUT: minimum length of time to wait
* until giving up on a path discovery (in milliseconds)
*
* @NL80211_MESHCONF_HWMP_ACTIVE_PATH_TIMEOUT: The time (in TUs) for which mesh
* points receiving a PREQ shall consider the forwarding information from
* the root to be valid. (TU = time unit)
*
* @NL80211_MESHCONF_HWMP_PREQ_MIN_INTERVAL: The minimum interval of time (in
* TUs) during which an MP can send only one action frame containing a PREQ
* reference element
*
* @NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME: The interval of time (in TUs)
* that it takes for an HWMP information element to propagate across the
* mesh
*
* @NL80211_MESHCONF_HWMP_ROOTMODE: whether root mode is enabled or not
*
* @NL80211_MESHCONF_ELEMENT_TTL: specifies the value of TTL field set at a
* source mesh point for path selection elements.
*
* @NL80211_MESHCONF_HWMP_RANN_INTERVAL: The interval of time (in TUs) between
* root announcements are transmitted.
*
* @NL80211_MESHCONF_GATE_ANNOUNCEMENTS: Advertise that this mesh station has
* access to a broader network beyond the MBSS. This is done via Root
* Announcement frames.
*
* @NL80211_MESHCONF_HWMP_PERR_MIN_INTERVAL: The minimum interval of time (in
* TUs) during which a mesh STA can send only one Action frame containing a
* PERR element.
*
* @NL80211_MESHCONF_FORWARDING: set Mesh STA as forwarding or non-forwarding
* or forwarding entity (default is TRUE - forwarding entity)
*
* @NL80211_MESHCONF_RSSI_THRESHOLD: RSSI threshold in dBm. This specifies the
* threshold for average signal strength of candidate station to establish
* a peer link.
*
* @NL80211_MESHCONF_SYNC_OFFSET_MAX_NEIGHBOR: maximum number of neighbors
* to synchronize to for 11s default synchronization method
* (see 11C.12.2.2)
*
* @NL80211_MESHCONF_HT_OPMODE: set mesh HT protection mode.
*
* @NL80211_MESHCONF_ATTR_MAX: highest possible mesh configuration attribute
*
* @NL80211_MESHCONF_HWMP_PATH_TO_ROOT_TIMEOUT: The time (in TUs) for
* which mesh STAs receiving a proactive PREQ shall consider the forwarding
* information to the root mesh STA to be valid.
*
* @NL80211_MESHCONF_HWMP_ROOT_INTERVAL: The interval of time (in TUs) between
* proactive PREQs are transmitted.
*
* @NL80211_MESHCONF_HWMP_CONFIRMATION_INTERVAL: The minimum interval of time
* (in TUs) during which a mesh STA can send only one Action frame
* containing a PREQ element for root path confirmation.
*
* @NL80211_MESHCONF_POWER_MODE: Default mesh power mode for new peer links.
* type &enum nl80211_mesh_power_mode (u32)
*
* @NL80211_MESHCONF_AWAKE_WINDOW: awake window duration (in TUs)
*
* @NL80211_MESHCONF_PLINK_TIMEOUT: If no tx activity is seen from a STA we've
* established peering with for longer than this time (in seconds), then
* remove it from the STA's list of peers. You may set this to 0 to disable
* the removal of the STA. Default is 30 minutes.
*
* @NL80211_MESHCONF_CONNECTED_TO_GATE: If set to true then this mesh STA
* will advertise that it is connected to a gate in the mesh formation
* field. If left unset then the mesh formation field will only
* advertise such if there is an active root mesh path.
*
* @NL80211_MESHCONF_NOLEARN: Try to avoid multi-hop path discovery (e.g.
* PREQ/PREP for HWMP) if the destination is a direct neighbor. Note that
* this might not be the optimal decision as a multi-hop route might be
* better. So if using this setting you will likely also want to disable
* dot11MeshForwarding and use another mesh routing protocol on top.
*
* @NL80211_MESHCONF_CONNECTED_TO_AS: If set to true then this mesh STA
* will advertise that it is connected to a authentication server
* in the mesh formation field.
*
* @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use
*/
enum nl80211_meshconf_params {
__NL80211_MESHCONF_INVALID,
NL80211_MESHCONF_RETRY_TIMEOUT,
NL80211_MESHCONF_CONFIRM_TIMEOUT,
NL80211_MESHCONF_HOLDING_TIMEOUT,
NL80211_MESHCONF_MAX_PEER_LINKS,
NL80211_MESHCONF_MAX_RETRIES,
NL80211_MESHCONF_TTL,
NL80211_MESHCONF_AUTO_OPEN_PLINKS,
NL80211_MESHCONF_HWMP_MAX_PREQ_RETRIES,
NL80211_MESHCONF_PATH_REFRESH_TIME,
NL80211_MESHCONF_MIN_DISCOVERY_TIMEOUT,
NL80211_MESHCONF_HWMP_ACTIVE_PATH_TIMEOUT,
NL80211_MESHCONF_HWMP_PREQ_MIN_INTERVAL,
NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME,
NL80211_MESHCONF_HWMP_ROOTMODE,
NL80211_MESHCONF_ELEMENT_TTL,
NL80211_MESHCONF_HWMP_RANN_INTERVAL,
NL80211_MESHCONF_GATE_ANNOUNCEMENTS,
NL80211_MESHCONF_HWMP_PERR_MIN_INTERVAL,
NL80211_MESHCONF_FORWARDING,
NL80211_MESHCONF_RSSI_THRESHOLD,
NL80211_MESHCONF_SYNC_OFFSET_MAX_NEIGHBOR,
NL80211_MESHCONF_HT_OPMODE,
NL80211_MESHCONF_HWMP_PATH_TO_ROOT_TIMEOUT,
NL80211_MESHCONF_HWMP_ROOT_INTERVAL,
NL80211_MESHCONF_HWMP_CONFIRMATION_INTERVAL,
NL80211_MESHCONF_POWER_MODE,
NL80211_MESHCONF_AWAKE_WINDOW,
NL80211_MESHCONF_PLINK_TIMEOUT,
NL80211_MESHCONF_CONNECTED_TO_GATE,
NL80211_MESHCONF_NOLEARN,
NL80211_MESHCONF_CONNECTED_TO_AS,
/* keep last */
__NL80211_MESHCONF_ATTR_AFTER_LAST,
NL80211_MESHCONF_ATTR_MAX = __NL80211_MESHCONF_ATTR_AFTER_LAST - 1
};
/**
* enum nl80211_mesh_setup_params - mesh setup parameters
*
* Mesh setup parameters. These are used to start/join a mesh and cannot be
* changed while the mesh is active.
*
* @__NL80211_MESH_SETUP_INVALID: Internal use
*
* @NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL: Enable this option to use a
* vendor specific path selection algorithm or disable it to use the
* default HWMP.
*
* @NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC: Enable this option to use a
* vendor specific path metric or disable it to use the default Airtime
* metric.
*
* @NL80211_MESH_SETUP_IE: Information elements for this mesh, for instance, a
* robust security network ie, or a vendor specific information element
* that vendors will use to identify the path selection methods and
* metrics in use.
*
* @NL80211_MESH_SETUP_USERSPACE_AUTH: Enable this option if an authentication
* daemon will be authenticating mesh candidates.
*
* @NL80211_MESH_SETUP_USERSPACE_AMPE: Enable this option if an authentication
* daemon will be securing peer link frames. AMPE is a secured version of
* Mesh Peering Management (MPM) and is implemented with the assistance of
* a userspace daemon. When this flag is set, the kernel will send peer
* management frames to a userspace daemon that will implement AMPE
* functionality (security capabilities selection, key confirmation, and
* key management). When the flag is unset (default), the kernel can
* autonomously complete (unsecured) mesh peering without the need of a
* userspace daemon.
*
* @NL80211_MESH_SETUP_ENABLE_VENDOR_SYNC: Enable this option to use a
* vendor specific synchronization method or disable it to use the default
* neighbor offset synchronization
*
* @NL80211_MESH_SETUP_USERSPACE_MPM: Enable this option if userspace will
* implement an MPM which handles peer allocation and state.
*
* @NL80211_MESH_SETUP_AUTH_PROTOCOL: Inform the kernel of the authentication
* method (u8, as defined in IEEE 8.4.2.100.6, e.g. 0x1 for SAE).
* Default is no authentication method required.
*
* @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number
*
* @__NL80211_MESH_SETUP_ATTR_AFTER_LAST: Internal use
*/
enum nl80211_mesh_setup_params {
__NL80211_MESH_SETUP_INVALID,
NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL,
NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC,
NL80211_MESH_SETUP_IE,
NL80211_MESH_SETUP_USERSPACE_AUTH,
NL80211_MESH_SETUP_USERSPACE_AMPE,
NL80211_MESH_SETUP_ENABLE_VENDOR_SYNC,
NL80211_MESH_SETUP_USERSPACE_MPM,
NL80211_MESH_SETUP_AUTH_PROTOCOL,
/* keep last */
__NL80211_MESH_SETUP_ATTR_AFTER_LAST,
NL80211_MESH_SETUP_ATTR_MAX = __NL80211_MESH_SETUP_ATTR_AFTER_LAST - 1
};
/**
* enum nl80211_txq_attr - TX queue parameter attributes
* @__NL80211_TXQ_ATTR_INVALID: Attribute number 0 is reserved
* @NL80211_TXQ_ATTR_AC: AC identifier (NL80211_AC_*)
* @NL80211_TXQ_ATTR_TXOP: Maximum burst time in units of 32 usecs, 0 meaning
* disabled
* @NL80211_TXQ_ATTR_CWMIN: Minimum contention window [a value of the form
* 2^n-1 in the range 1..32767]
* @NL80211_TXQ_ATTR_CWMAX: Maximum contention window [a value of the form
* 2^n-1 in the range 1..32767]
* @NL80211_TXQ_ATTR_AIFS: Arbitration interframe space [0..255]
* @__NL80211_TXQ_ATTR_AFTER_LAST: Internal
* @NL80211_TXQ_ATTR_MAX: Maximum TXQ attribute number
*/
enum nl80211_txq_attr {
__NL80211_TXQ_ATTR_INVALID,
NL80211_TXQ_ATTR_AC,
NL80211_TXQ_ATTR_TXOP,
NL80211_TXQ_ATTR_CWMIN,
NL80211_TXQ_ATTR_CWMAX,
NL80211_TXQ_ATTR_AIFS,
/* keep last */
__NL80211_TXQ_ATTR_AFTER_LAST,
NL80211_TXQ_ATTR_MAX = __NL80211_TXQ_ATTR_AFTER_LAST - 1
};
enum nl80211_ac {
NL80211_AC_VO,
NL80211_AC_VI,
NL80211_AC_BE,
NL80211_AC_BK,
NL80211_NUM_ACS
};
/* backward compat */
#define NL80211_TXQ_ATTR_QUEUE NL80211_TXQ_ATTR_AC
#define NL80211_TXQ_Q_VO NL80211_AC_VO
#define NL80211_TXQ_Q_VI NL80211_AC_VI
#define NL80211_TXQ_Q_BE NL80211_AC_BE
#define NL80211_TXQ_Q_BK NL80211_AC_BK
/**
* enum nl80211_channel_type - channel type
* @NL80211_CHAN_NO_HT: 20 MHz, non-HT channel
* @NL80211_CHAN_HT20: 20 MHz HT channel
* @NL80211_CHAN_HT40MINUS: HT40 channel, secondary channel
* below the control channel
* @NL80211_CHAN_HT40PLUS: HT40 channel, secondary channel
* above the control channel
*/
enum nl80211_channel_type {
NL80211_CHAN_NO_HT,
NL80211_CHAN_HT20,
NL80211_CHAN_HT40MINUS,
NL80211_CHAN_HT40PLUS
};
/**
* enum nl80211_key_mode - Key mode
*
* @NL80211_KEY_RX_TX: (Default)
* Key can be used for Rx and Tx immediately
*
* The following modes can only be selected for unicast keys and when the
* driver supports @NL80211_EXT_FEATURE_EXT_KEY_ID:
*
* @NL80211_KEY_NO_TX: Only allowed in combination with @NL80211_CMD_NEW_KEY:
* Unicast key can only be used for Rx, Tx not allowed, yet
* @NL80211_KEY_SET_TX: Only allowed in combination with @NL80211_CMD_SET_KEY:
* The unicast key identified by idx and mac is cleared for Tx and becomes
* the preferred Tx key for the station.
*/
enum nl80211_key_mode {
NL80211_KEY_RX_TX,
NL80211_KEY_NO_TX,
NL80211_KEY_SET_TX
};
/**
* enum nl80211_chan_width - channel width definitions
*
* These values are used with the %NL80211_ATTR_CHANNEL_WIDTH
* attribute.
*
* @NL80211_CHAN_WIDTH_20_NOHT: 20 MHz, non-HT channel
* @NL80211_CHAN_WIDTH_20: 20 MHz HT channel
* @NL80211_CHAN_WIDTH_40: 40 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
* attribute must be provided as well
* @NL80211_CHAN_WIDTH_80: 80 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
* attribute must be provided as well
* @NL80211_CHAN_WIDTH_80P80: 80+80 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
* and %NL80211_ATTR_CENTER_FREQ2 attributes must be provided as well
* @NL80211_CHAN_WIDTH_160: 160 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
* attribute must be provided as well
* @NL80211_CHAN_WIDTH_5: 5 MHz OFDM channel
* @NL80211_CHAN_WIDTH_10: 10 MHz OFDM channel
* @NL80211_CHAN_WIDTH_1: 1 MHz OFDM channel
* @NL80211_CHAN_WIDTH_2: 2 MHz OFDM channel
* @NL80211_CHAN_WIDTH_4: 4 MHz OFDM channel
* @NL80211_CHAN_WIDTH_8: 8 MHz OFDM channel
* @NL80211_CHAN_WIDTH_16: 16 MHz OFDM channel
* @NL80211_CHAN_WIDTH_320: 320 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
* attribute must be provided as well
*/
enum nl80211_chan_width {
NL80211_CHAN_WIDTH_20_NOHT,
NL80211_CHAN_WIDTH_20,
NL80211_CHAN_WIDTH_40,
NL80211_CHAN_WIDTH_80,
NL80211_CHAN_WIDTH_80P80,
NL80211_CHAN_WIDTH_160,
NL80211_CHAN_WIDTH_5,
NL80211_CHAN_WIDTH_10,
NL80211_CHAN_WIDTH_1,
NL80211_CHAN_WIDTH_2,
NL80211_CHAN_WIDTH_4,
NL80211_CHAN_WIDTH_8,
NL80211_CHAN_WIDTH_16,
NL80211_CHAN_WIDTH_320,
};
/**
* enum nl80211_bss_scan_width - control channel width for a BSS
*
* These values are used with the %NL80211_BSS_CHAN_WIDTH attribute.
*
* @NL80211_BSS_CHAN_WIDTH_20: control channel is 20 MHz wide or compatible
* @NL80211_BSS_CHAN_WIDTH_10: control channel is 10 MHz wide
* @NL80211_BSS_CHAN_WIDTH_5: control channel is 5 MHz wide
* @NL80211_BSS_CHAN_WIDTH_1: control channel is 1 MHz wide
* @NL80211_BSS_CHAN_WIDTH_2: control channel is 2 MHz wide
*/
enum nl80211_bss_scan_width {
NL80211_BSS_CHAN_WIDTH_20,
NL80211_BSS_CHAN_WIDTH_10,
NL80211_BSS_CHAN_WIDTH_5,
NL80211_BSS_CHAN_WIDTH_1,
NL80211_BSS_CHAN_WIDTH_2,
};
/**
* enum nl80211_bss - netlink attributes for a BSS
*
* @__NL80211_BSS_INVALID: invalid
* @NL80211_BSS_BSSID: BSSID of the BSS (6 octets)
* @NL80211_BSS_FREQUENCY: frequency in MHz (u32)
* @NL80211_BSS_TSF: TSF of the received probe response/beacon (u64)
* (if @NL80211_BSS_PRESP_DATA is present then this is known to be
* from a probe response, otherwise it may be from the same beacon
* that the NL80211_BSS_BEACON_TSF will be from)
* @NL80211_BSS_BEACON_INTERVAL: beacon interval of the (I)BSS (u16)
* @NL80211_BSS_CAPABILITY: capability field (CPU order, u16)
* @NL80211_BSS_INFORMATION_ELEMENTS: binary attribute containing the
* raw information elements from the probe response/beacon (bin);
* if the %NL80211_BSS_BEACON_IES attribute is present and the data is
* different then the IEs here are from a Probe Response frame; otherwise
* they are from a Beacon frame.
* However, if the driver does not indicate the source of the IEs, these
* IEs may be from either frame subtype.
* If present, the @NL80211_BSS_PRESP_DATA attribute indicates that the
* data here is known to be from a probe response, without any heuristics.
* @NL80211_BSS_SIGNAL_MBM: signal strength of probe response/beacon
* in mBm (100 * dBm) (s32)
* @NL80211_BSS_SIGNAL_UNSPEC: signal strength of the probe response/beacon
* in unspecified units, scaled to 0..100 (u8)
* @NL80211_BSS_STATUS: status, if this BSS is "used"
* @NL80211_BSS_SEEN_MS_AGO: age of this BSS entry in ms
* @NL80211_BSS_BEACON_IES: binary attribute containing the raw information
* elements from a Beacon frame (bin); not present if no Beacon frame has
* yet been received
* @NL80211_BSS_CHAN_WIDTH: channel width of the control channel
* (u32, enum nl80211_bss_scan_width)
* @NL80211_BSS_BEACON_TSF: TSF of the last received beacon (u64)
* (not present if no beacon frame has been received yet)
* @NL80211_BSS_PRESP_DATA: the data in @NL80211_BSS_INFORMATION_ELEMENTS and
* @NL80211_BSS_TSF is known to be from a probe response (flag attribute)
* @NL80211_BSS_LAST_SEEN_BOOTTIME: CLOCK_BOOTTIME timestamp when this entry
* was last updated by a received frame. The value is expected to be
* accurate to about 10ms. (u64, nanoseconds)
* @NL80211_BSS_PAD: attribute used for padding for 64-bit alignment
* @NL80211_BSS_PARENT_TSF: the time at the start of reception of the first
* octet of the timestamp field of the last beacon/probe received for
* this BSS. The time is the TSF of the BSS specified by
* @NL80211_BSS_PARENT_BSSID. (u64).
* @NL80211_BSS_PARENT_BSSID: the BSS according to which @NL80211_BSS_PARENT_TSF
* is set.
* @NL80211_BSS_CHAIN_SIGNAL: per-chain signal strength of last BSS update.
* Contains a nested array of signal strength attributes (u8, dBm),
* using the nesting index as the antenna number.
* @NL80211_BSS_FREQUENCY_OFFSET: frequency offset in KHz
* @NL80211_BSS_MLO_LINK_ID: MLO link ID of the BSS (u8).
* @NL80211_BSS_MLD_ADDR: MLD address of this BSS if connected to it.
* @__NL80211_BSS_AFTER_LAST: internal
* @NL80211_BSS_MAX: highest BSS attribute
*/
enum nl80211_bss {
__NL80211_BSS_INVALID,
NL80211_BSS_BSSID,
NL80211_BSS_FREQUENCY,
NL80211_BSS_TSF,
NL80211_BSS_BEACON_INTERVAL,
NL80211_BSS_CAPABILITY,
NL80211_BSS_INFORMATION_ELEMENTS,
NL80211_BSS_SIGNAL_MBM,
NL80211_BSS_SIGNAL_UNSPEC,
NL80211_BSS_STATUS,
NL80211_BSS_SEEN_MS_AGO,
NL80211_BSS_BEACON_IES,
NL80211_BSS_CHAN_WIDTH,
NL80211_BSS_BEACON_TSF,
NL80211_BSS_PRESP_DATA,
NL80211_BSS_LAST_SEEN_BOOTTIME,
NL80211_BSS_PAD,
NL80211_BSS_PARENT_TSF,
NL80211_BSS_PARENT_BSSID,
NL80211_BSS_CHAIN_SIGNAL,
NL80211_BSS_FREQUENCY_OFFSET,
NL80211_BSS_MLO_LINK_ID,
NL80211_BSS_MLD_ADDR,
/* keep last */
__NL80211_BSS_AFTER_LAST,
NL80211_BSS_MAX = __NL80211_BSS_AFTER_LAST - 1
};
/**
* enum nl80211_bss_status - BSS "status"
* @NL80211_BSS_STATUS_AUTHENTICATED: Authenticated with this BSS.
* Note that this is no longer used since cfg80211 no longer
* keeps track of whether or not authentication was done with
* a given BSS.
* @NL80211_BSS_STATUS_ASSOCIATED: Associated with this BSS.
* @NL80211_BSS_STATUS_IBSS_JOINED: Joined to this IBSS.
*
* The BSS status is a BSS attribute in scan dumps, which
* indicates the status the interface has wrt. this BSS.
*/
enum nl80211_bss_status {
NL80211_BSS_STATUS_AUTHENTICATED,
NL80211_BSS_STATUS_ASSOCIATED,
NL80211_BSS_STATUS_IBSS_JOINED,
};
/**
* enum nl80211_auth_type - AuthenticationType
*
* @NL80211_AUTHTYPE_OPEN_SYSTEM: Open System authentication
* @NL80211_AUTHTYPE_SHARED_KEY: Shared Key authentication (WEP only)
* @NL80211_AUTHTYPE_FT: Fast BSS Transition (IEEE 802.11r)
* @NL80211_AUTHTYPE_NETWORK_EAP: Network EAP (some Cisco APs and mainly LEAP)
* @NL80211_AUTHTYPE_SAE: Simultaneous authentication of equals
* @NL80211_AUTHTYPE_FILS_SK: Fast Initial Link Setup shared key
* @NL80211_AUTHTYPE_FILS_SK_PFS: Fast Initial Link Setup shared key with PFS
* @NL80211_AUTHTYPE_FILS_PK: Fast Initial Link Setup public key
* @__NL80211_AUTHTYPE_NUM: internal
* @NL80211_AUTHTYPE_MAX: maximum valid auth algorithm
* @NL80211_AUTHTYPE_AUTOMATIC: determine automatically (if necessary by
* trying multiple times); this is invalid in netlink -- leave out
* the attribute for this on CONNECT commands.
*/
enum nl80211_auth_type {
NL80211_AUTHTYPE_OPEN_SYSTEM,
NL80211_AUTHTYPE_SHARED_KEY,
NL80211_AUTHTYPE_FT,
NL80211_AUTHTYPE_NETWORK_EAP,
NL80211_AUTHTYPE_SAE,
NL80211_AUTHTYPE_FILS_SK,
NL80211_AUTHTYPE_FILS_SK_PFS,
NL80211_AUTHTYPE_FILS_PK,
/* keep last */
__NL80211_AUTHTYPE_NUM,
NL80211_AUTHTYPE_MAX = __NL80211_AUTHTYPE_NUM - 1,
NL80211_AUTHTYPE_AUTOMATIC
};
/**
* enum nl80211_key_type - Key Type
* @NL80211_KEYTYPE_GROUP: Group (broadcast/multicast) key
* @NL80211_KEYTYPE_PAIRWISE: Pairwise (unicast/individual) key
* @NL80211_KEYTYPE_PEERKEY: PeerKey (DLS)
* @NUM_NL80211_KEYTYPES: number of defined key types
*/
enum nl80211_key_type {
NL80211_KEYTYPE_GROUP,
NL80211_KEYTYPE_PAIRWISE,
NL80211_KEYTYPE_PEERKEY,
NUM_NL80211_KEYTYPES
};
/**
* enum nl80211_mfp - Management frame protection state
* @NL80211_MFP_NO: Management frame protection not used
* @NL80211_MFP_REQUIRED: Management frame protection required
* @NL80211_MFP_OPTIONAL: Management frame protection is optional
*/
enum nl80211_mfp {
NL80211_MFP_NO,
NL80211_MFP_REQUIRED,
NL80211_MFP_OPTIONAL,
};
enum nl80211_wpa_versions {
NL80211_WPA_VERSION_1 = 1 << 0,
NL80211_WPA_VERSION_2 = 1 << 1,
NL80211_WPA_VERSION_3 = 1 << 2,
};
/**
* enum nl80211_key_default_types - key default types
* @__NL80211_KEY_DEFAULT_TYPE_INVALID: invalid
* @NL80211_KEY_DEFAULT_TYPE_UNICAST: key should be used as default
* unicast key
* @NL80211_KEY_DEFAULT_TYPE_MULTICAST: key should be used as default
* multicast key
* @NUM_NL80211_KEY_DEFAULT_TYPES: number of default types
*/
enum nl80211_key_default_types {
__NL80211_KEY_DEFAULT_TYPE_INVALID,
NL80211_KEY_DEFAULT_TYPE_UNICAST,
NL80211_KEY_DEFAULT_TYPE_MULTICAST,
NUM_NL80211_KEY_DEFAULT_TYPES
};
/**
* enum nl80211_key_attributes - key attributes
* @__NL80211_KEY_INVALID: invalid
* @NL80211_KEY_DATA: (temporal) key data; for TKIP this consists of
* 16 bytes encryption key followed by 8 bytes each for TX and RX MIC
* keys
* @NL80211_KEY_IDX: key ID (u8, 0-3)
* @NL80211_KEY_CIPHER: key cipher suite (u32, as defined by IEEE 802.11
* section 7.3.2.25.1, e.g. 0x000FAC04)
* @NL80211_KEY_SEQ: transmit key sequence number (IV/PN) for TKIP and
* CCMP keys, each six bytes in little endian
* @NL80211_KEY_DEFAULT: flag indicating default key
* @NL80211_KEY_DEFAULT_MGMT: flag indicating default management key
* @NL80211_KEY_TYPE: the key type from enum nl80211_key_type, if not
* specified the default depends on whether a MAC address was
* given with the command using the key or not (u32)
* @NL80211_KEY_DEFAULT_TYPES: A nested attribute containing flags
* attributes, specifying what a key should be set as default as.
* See &enum nl80211_key_default_types.
* @NL80211_KEY_MODE: the mode from enum nl80211_key_mode.
* Defaults to @NL80211_KEY_RX_TX.
* @NL80211_KEY_DEFAULT_BEACON: flag indicating default Beacon frame key
*
* @__NL80211_KEY_AFTER_LAST: internal
* @NL80211_KEY_MAX: highest key attribute
*/
enum nl80211_key_attributes {
__NL80211_KEY_INVALID,
NL80211_KEY_DATA,
NL80211_KEY_IDX,
NL80211_KEY_CIPHER,
NL80211_KEY_SEQ,
NL80211_KEY_DEFAULT,
NL80211_KEY_DEFAULT_MGMT,
NL80211_KEY_TYPE,
NL80211_KEY_DEFAULT_TYPES,
NL80211_KEY_MODE,
NL80211_KEY_DEFAULT_BEACON,
/* keep last */
__NL80211_KEY_AFTER_LAST,
NL80211_KEY_MAX = __NL80211_KEY_AFTER_LAST - 1
};
/**
* enum nl80211_tx_rate_attributes - TX rate set attributes
* @__NL80211_TXRATE_INVALID: invalid
* @NL80211_TXRATE_LEGACY: Legacy (non-MCS) rates allowed for TX rate selection
* in an array of rates as defined in IEEE 802.11 7.3.2.2 (u8 values with
* 1 = 500 kbps) but without the IE length restriction (at most
* %NL80211_MAX_SUPP_RATES in a single array).
* @NL80211_TXRATE_HT: HT (MCS) rates allowed for TX rate selection
* in an array of MCS numbers.
* @NL80211_TXRATE_VHT: VHT rates allowed for TX rate selection,
* see &struct nl80211_txrate_vht
* @NL80211_TXRATE_GI: configure GI, see &enum nl80211_txrate_gi
* @NL80211_TXRATE_HE: HE rates allowed for TX rate selection,
* see &struct nl80211_txrate_he
* @NL80211_TXRATE_HE_GI: configure HE GI, 0.8us, 1.6us and 3.2us.
* @NL80211_TXRATE_HE_LTF: configure HE LTF, 1XLTF, 2XLTF and 4XLTF.
* @__NL80211_TXRATE_AFTER_LAST: internal
* @NL80211_TXRATE_MAX: highest TX rate attribute
*/
enum nl80211_tx_rate_attributes {
__NL80211_TXRATE_INVALID,
NL80211_TXRATE_LEGACY,
NL80211_TXRATE_HT,
NL80211_TXRATE_VHT,
NL80211_TXRATE_GI,
NL80211_TXRATE_HE,
NL80211_TXRATE_HE_GI,
NL80211_TXRATE_HE_LTF,
/* keep last */
__NL80211_TXRATE_AFTER_LAST,
NL80211_TXRATE_MAX = __NL80211_TXRATE_AFTER_LAST - 1
};
#define NL80211_TXRATE_MCS NL80211_TXRATE_HT
#define NL80211_VHT_NSS_MAX 8
/**
* struct nl80211_txrate_vht - VHT MCS/NSS txrate bitmap
* @mcs: MCS bitmap table for each NSS (array index 0 for 1 stream, etc.)
*/
struct nl80211_txrate_vht {
__u16 mcs[NL80211_VHT_NSS_MAX];
};
#define NL80211_HE_NSS_MAX 8
/**
* struct nl80211_txrate_he - HE MCS/NSS txrate bitmap
* @mcs: MCS bitmap table for each NSS (array index 0 for 1 stream, etc.)
*/
struct nl80211_txrate_he {
__u16 mcs[NL80211_HE_NSS_MAX];
};
enum nl80211_txrate_gi {
NL80211_TXRATE_DEFAULT_GI,
NL80211_TXRATE_FORCE_SGI,
NL80211_TXRATE_FORCE_LGI,
};
/**
* enum nl80211_band - Frequency band
* @NL80211_BAND_2GHZ: 2.4 GHz ISM band
* @NL80211_BAND_5GHZ: around 5 GHz band (4.9 - 5.7 GHz)
* @NL80211_BAND_60GHZ: around 60 GHz band (58.32 - 69.12 GHz)
* @NL80211_BAND_6GHZ: around 6 GHz band (5.9 - 7.2 GHz)
* @NL80211_BAND_S1GHZ: around 900MHz, supported by S1G PHYs
* @NL80211_BAND_LC: light communication band (placeholder)
* @NUM_NL80211_BANDS: number of bands, avoid using this in userspace
* since newer kernel versions may support more bands
*/
enum nl80211_band {
NL80211_BAND_2GHZ,
NL80211_BAND_5GHZ,
NL80211_BAND_60GHZ,
NL80211_BAND_6GHZ,
NL80211_BAND_S1GHZ,
NL80211_BAND_LC,
NUM_NL80211_BANDS,
};
/**
* enum nl80211_ps_state - powersave state
* @NL80211_PS_DISABLED: powersave is disabled
* @NL80211_PS_ENABLED: powersave is enabled
*/
enum nl80211_ps_state {
NL80211_PS_DISABLED,
NL80211_PS_ENABLED,
};
/**
* enum nl80211_attr_cqm - connection quality monitor attributes
* @__NL80211_ATTR_CQM_INVALID: invalid
* @NL80211_ATTR_CQM_RSSI_THOLD: RSSI threshold in dBm. This value specifies
* the threshold for the RSSI level at which an event will be sent. Zero
* to disable. Alternatively, if %NL80211_EXT_FEATURE_CQM_RSSI_LIST is
* set, multiple values can be supplied as a low-to-high sorted array of
* threshold values in dBm. Events will be sent when the RSSI value
* crosses any of the thresholds.
* @NL80211_ATTR_CQM_RSSI_HYST: RSSI hysteresis in dBm. This value specifies
* the minimum amount the RSSI level must change after an event before a
* new event may be issued (to reduce effects of RSSI oscillation).
* @NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT: RSSI threshold event
* @NL80211_ATTR_CQM_PKT_LOSS_EVENT: a u32 value indicating that this many
* consecutive packets were not acknowledged by the peer
* @NL80211_ATTR_CQM_TXE_RATE: TX error rate in %. Minimum % of TX failures
* during the given %NL80211_ATTR_CQM_TXE_INTVL before an
* %NL80211_CMD_NOTIFY_CQM with reported %NL80211_ATTR_CQM_TXE_RATE and
* %NL80211_ATTR_CQM_TXE_PKTS is generated.
* @NL80211_ATTR_CQM_TXE_PKTS: number of attempted packets in a given
* %NL80211_ATTR_CQM_TXE_INTVL before %NL80211_ATTR_CQM_TXE_RATE is
* checked.
* @NL80211_ATTR_CQM_TXE_INTVL: interval in seconds. Specifies the periodic
* interval in which %NL80211_ATTR_CQM_TXE_PKTS and
* %NL80211_ATTR_CQM_TXE_RATE must be satisfied before generating an
* %NL80211_CMD_NOTIFY_CQM. Set to 0 to turn off TX error reporting.
* @NL80211_ATTR_CQM_BEACON_LOSS_EVENT: flag attribute that's set in a beacon
* loss event
* @NL80211_ATTR_CQM_RSSI_LEVEL: the RSSI value in dBm that triggered the
* RSSI threshold event.
* @__NL80211_ATTR_CQM_AFTER_LAST: internal
* @NL80211_ATTR_CQM_MAX: highest key attribute
*/
enum nl80211_attr_cqm {
__NL80211_ATTR_CQM_INVALID,
NL80211_ATTR_CQM_RSSI_THOLD,
NL80211_ATTR_CQM_RSSI_HYST,
NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT,
NL80211_ATTR_CQM_PKT_LOSS_EVENT,
NL80211_ATTR_CQM_TXE_RATE,
NL80211_ATTR_CQM_TXE_PKTS,
NL80211_ATTR_CQM_TXE_INTVL,
NL80211_ATTR_CQM_BEACON_LOSS_EVENT,
NL80211_ATTR_CQM_RSSI_LEVEL,
/* keep last */
__NL80211_ATTR_CQM_AFTER_LAST,
NL80211_ATTR_CQM_MAX = __NL80211_ATTR_CQM_AFTER_LAST - 1
};
/**
* enum nl80211_cqm_rssi_threshold_event - RSSI threshold event
* @NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW: The RSSI level is lower than the
* configured threshold
* @NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH: The RSSI is higher than the
* configured threshold
* @NL80211_CQM_RSSI_BEACON_LOSS_EVENT: (reserved, never sent)
*/
enum nl80211_cqm_rssi_threshold_event {
NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW,
NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH,
NL80211_CQM_RSSI_BEACON_LOSS_EVENT,
};
/**
* enum nl80211_tx_power_setting - TX power adjustment
* @NL80211_TX_POWER_AUTOMATIC: automatically determine transmit power
* @NL80211_TX_POWER_LIMITED: limit TX power by the mBm parameter
* @NL80211_TX_POWER_FIXED: fix TX power to the mBm parameter
*/
enum nl80211_tx_power_setting {
NL80211_TX_POWER_AUTOMATIC,
NL80211_TX_POWER_LIMITED,
NL80211_TX_POWER_FIXED,
};
/**
* enum nl80211_tid_config - TID config state
* @NL80211_TID_CONFIG_ENABLE: Enable config for the TID
* @NL80211_TID_CONFIG_DISABLE: Disable config for the TID
*/
enum nl80211_tid_config {
NL80211_TID_CONFIG_ENABLE,
NL80211_TID_CONFIG_DISABLE,
};
/* enum nl80211_tx_rate_setting - TX rate configuration type
* @NL80211_TX_RATE_AUTOMATIC: automatically determine TX rate
* @NL80211_TX_RATE_LIMITED: limit the TX rate by the TX rate parameter
* @NL80211_TX_RATE_FIXED: fix TX rate to the TX rate parameter
*/
enum nl80211_tx_rate_setting {
NL80211_TX_RATE_AUTOMATIC,
NL80211_TX_RATE_LIMITED,
NL80211_TX_RATE_FIXED,
};
/* enum nl80211_tid_config_attr - TID specific configuration.
* @NL80211_TID_CONFIG_ATTR_PAD: pad attribute for 64-bit values
* @NL80211_TID_CONFIG_ATTR_VIF_SUPP: a bitmap (u64) of attributes supported
* for per-vif configuration; doesn't list the ones that are generic
* (%NL80211_TID_CONFIG_ATTR_TIDS, %NL80211_TID_CONFIG_ATTR_OVERRIDE).
* @NL80211_TID_CONFIG_ATTR_PEER_SUPP: same as the previous per-vif one, but
* per peer instead.
* @NL80211_TID_CONFIG_ATTR_OVERRIDE: flag attribue, if set indicates
* that the new configuration overrides all previous peer
* configurations, otherwise previous peer specific configurations
* should be left untouched.
* @NL80211_TID_CONFIG_ATTR_TIDS: a bitmask value of TIDs (bit 0 to 7)
* Its type is u16.
* @NL80211_TID_CONFIG_ATTR_NOACK: Configure ack policy for the TID.
* specified in %NL80211_TID_CONFIG_ATTR_TID. see %enum nl80211_tid_config.
* Its type is u8.
* @NL80211_TID_CONFIG_ATTR_RETRY_SHORT: Number of retries used with data frame
* transmission, user-space sets this configuration in
* &NL80211_CMD_SET_TID_CONFIG. It is u8 type, min value is 1 and
* the max value is advertised by the driver in this attribute on
* output in wiphy capabilities.
* @NL80211_TID_CONFIG_ATTR_RETRY_LONG: Number of retries used with data frame
* transmission, user-space sets this configuration in
* &NL80211_CMD_SET_TID_CONFIG. Its type is u8, min value is 1 and
* the max value is advertised by the driver in this attribute on
* output in wiphy capabilities.
* @NL80211_TID_CONFIG_ATTR_AMPDU_CTRL: Enable/Disable MPDU aggregation
* for the TIDs specified in %NL80211_TID_CONFIG_ATTR_TIDS.
* Its type is u8, using the values from &nl80211_tid_config.
* @NL80211_TID_CONFIG_ATTR_RTSCTS_CTRL: Enable/Disable RTS_CTS for the TIDs
* specified in %NL80211_TID_CONFIG_ATTR_TIDS. It is u8 type, using
* the values from &nl80211_tid_config.
* @NL80211_TID_CONFIG_ATTR_AMSDU_CTRL: Enable/Disable MSDU aggregation
* for the TIDs specified in %NL80211_TID_CONFIG_ATTR_TIDS.
* Its type is u8, using the values from &nl80211_tid_config.
* @NL80211_TID_CONFIG_ATTR_TX_RATE_TYPE: This attribute will be useful
* to notfiy the driver that what type of txrate should be used
* for the TIDs specified in %NL80211_TID_CONFIG_ATTR_TIDS. using
* the values form &nl80211_tx_rate_setting.
* @NL80211_TID_CONFIG_ATTR_TX_RATE: Data frame TX rate mask should be applied
* with the parameters passed through %NL80211_ATTR_TX_RATES.
* configuration is applied to the data frame for the tid to that connected
* station.
*/
enum nl80211_tid_config_attr {
__NL80211_TID_CONFIG_ATTR_INVALID,
NL80211_TID_CONFIG_ATTR_PAD,
NL80211_TID_CONFIG_ATTR_VIF_SUPP,
NL80211_TID_CONFIG_ATTR_PEER_SUPP,
NL80211_TID_CONFIG_ATTR_OVERRIDE,
NL80211_TID_CONFIG_ATTR_TIDS,
NL80211_TID_CONFIG_ATTR_NOACK,
NL80211_TID_CONFIG_ATTR_RETRY_SHORT,
NL80211_TID_CONFIG_ATTR_RETRY_LONG,
NL80211_TID_CONFIG_ATTR_AMPDU_CTRL,
NL80211_TID_CONFIG_ATTR_RTSCTS_CTRL,
NL80211_TID_CONFIG_ATTR_AMSDU_CTRL,
NL80211_TID_CONFIG_ATTR_TX_RATE_TYPE,
NL80211_TID_CONFIG_ATTR_TX_RATE,
/* keep last */
__NL80211_TID_CONFIG_ATTR_AFTER_LAST,
NL80211_TID_CONFIG_ATTR_MAX = __NL80211_TID_CONFIG_ATTR_AFTER_LAST - 1
};
/**
* enum nl80211_packet_pattern_attr - packet pattern attribute
* @__NL80211_PKTPAT_INVALID: invalid number for nested attribute
* @NL80211_PKTPAT_PATTERN: the pattern, values where the mask has
* a zero bit are ignored
* @NL80211_PKTPAT_MASK: pattern mask, must be long enough to have
* a bit for each byte in the pattern. The lowest-order bit corresponds
* to the first byte of the pattern, but the bytes of the pattern are
* in a little-endian-like format, i.e. the 9th byte of the pattern
* corresponds to the lowest-order bit in the second byte of the mask.
* For example: The match 00:xx:00:00:xx:00:00:00:00:xx:xx:xx (where
* xx indicates "don't care") would be represented by a pattern of
* twelve zero bytes, and a mask of "0xed,0x01".
* Note that the pattern matching is done as though frames were not
* 802.11 frames but 802.3 frames, i.e. the frame is fully unpacked
* first (including SNAP header unpacking) and then matched.
* @NL80211_PKTPAT_OFFSET: packet offset, pattern is matched after
* these fixed number of bytes of received packet
* @NUM_NL80211_PKTPAT: number of attributes
* @MAX_NL80211_PKTPAT: max attribute number
*/
enum nl80211_packet_pattern_attr {
__NL80211_PKTPAT_INVALID,
NL80211_PKTPAT_MASK,
NL80211_PKTPAT_PATTERN,
NL80211_PKTPAT_OFFSET,
NUM_NL80211_PKTPAT,
MAX_NL80211_PKTPAT = NUM_NL80211_PKTPAT - 1,
};
/**
* struct nl80211_pattern_support - packet pattern support information
* @max_patterns: maximum number of patterns supported
* @min_pattern_len: minimum length of each pattern
* @max_pattern_len: maximum length of each pattern
* @max_pkt_offset: maximum Rx packet offset
*
* This struct is carried in %NL80211_WOWLAN_TRIG_PKT_PATTERN when
* that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED or in
* %NL80211_ATTR_COALESCE_RULE_PKT_PATTERN when that is part of
* %NL80211_ATTR_COALESCE_RULE in the capability information given
* by the kernel to userspace.
*/
struct nl80211_pattern_support {
__u32 max_patterns;
__u32 min_pattern_len;
__u32 max_pattern_len;
__u32 max_pkt_offset;
} __attribute__((packed));
/* only for backward compatibility */
#define __NL80211_WOWLAN_PKTPAT_INVALID __NL80211_PKTPAT_INVALID
#define NL80211_WOWLAN_PKTPAT_MASK NL80211_PKTPAT_MASK
#define NL80211_WOWLAN_PKTPAT_PATTERN NL80211_PKTPAT_PATTERN
#define NL80211_WOWLAN_PKTPAT_OFFSET NL80211_PKTPAT_OFFSET
#define NUM_NL80211_WOWLAN_PKTPAT NUM_NL80211_PKTPAT
#define MAX_NL80211_WOWLAN_PKTPAT MAX_NL80211_PKTPAT
#define nl80211_wowlan_pattern_support nl80211_pattern_support
/**
* enum nl80211_wowlan_triggers - WoWLAN trigger definitions
* @__NL80211_WOWLAN_TRIG_INVALID: invalid number for nested attributes
* @NL80211_WOWLAN_TRIG_ANY: wake up on any activity, do not really put
* the chip into a special state -- works best with chips that have
* support for low-power operation already (flag)
* Note that this mode is incompatible with all of the others, if
* any others are even supported by the device.
* @NL80211_WOWLAN_TRIG_DISCONNECT: wake up on disconnect, the way disconnect
* is detected is implementation-specific (flag)
* @NL80211_WOWLAN_TRIG_MAGIC_PKT: wake up on magic packet (6x 0xff, followed
* by 16 repetitions of MAC addr, anywhere in payload) (flag)
* @NL80211_WOWLAN_TRIG_PKT_PATTERN: wake up on the specified packet patterns
* which are passed in an array of nested attributes, each nested attribute
* defining a with attributes from &struct nl80211_wowlan_trig_pkt_pattern.
* Each pattern defines a wakeup packet. Packet offset is associated with
* each pattern which is used while matching the pattern. The matching is
* done on the MSDU, i.e. as though the packet was an 802.3 packet, so the
* pattern matching is done after the packet is converted to the MSDU.
*
* In %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, it is a binary attribute
* carrying a &struct nl80211_pattern_support.
*
* When reporting wakeup. it is a u32 attribute containing the 0-based
* index of the pattern that caused the wakeup, in the patterns passed
* to the kernel when configuring.
* @NL80211_WOWLAN_TRIG_GTK_REKEY_SUPPORTED: Not a real trigger, and cannot be
* used when setting, used only to indicate that GTK rekeying is supported
* by the device (flag)
* @NL80211_WOWLAN_TRIG_GTK_REKEY_FAILURE: wake up on GTK rekey failure (if
* done by the device) (flag)
* @NL80211_WOWLAN_TRIG_EAP_IDENT_REQUEST: wake up on EAP Identity Request
* packet (flag)
* @NL80211_WOWLAN_TRIG_4WAY_HANDSHAKE: wake up on 4-way handshake (flag)
* @NL80211_WOWLAN_TRIG_RFKILL_RELEASE: wake up when rfkill is released
* (on devices that have rfkill in the device) (flag)
* @NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211: For wakeup reporting only, contains
* the 802.11 packet that caused the wakeup, e.g. a deauth frame. The frame
* may be truncated, the @NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211_LEN
* attribute contains the original length.
* @NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211_LEN: Original length of the 802.11
* packet, may be bigger than the @NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211
* attribute if the packet was truncated somewhere.
* @NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023: For wakeup reporting only, contains the
* 802.11 packet that caused the wakeup, e.g. a magic packet. The frame may
* be truncated, the @NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023_LEN attribute
* contains the original length.
* @NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023_LEN: Original length of the 802.3
* packet, may be bigger than the @NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023
* attribute if the packet was truncated somewhere.
* @NL80211_WOWLAN_TRIG_TCP_CONNECTION: TCP connection wake, see DOC section
* "TCP connection wakeup" for more details. This is a nested attribute
* containing the exact information for establishing and keeping alive
* the TCP connection.
* @NL80211_WOWLAN_TRIG_TCP_WAKEUP_MATCH: For wakeup reporting only, the
* wakeup packet was received on the TCP connection
* @NL80211_WOWLAN_TRIG_WAKEUP_TCP_CONNLOST: For wakeup reporting only, the
* TCP connection was lost or failed to be established
* @NL80211_WOWLAN_TRIG_WAKEUP_TCP_NOMORETOKENS: For wakeup reporting only,
* the TCP connection ran out of tokens to use for data to send to the
* service
* @NL80211_WOWLAN_TRIG_NET_DETECT: wake up when a configured network
* is detected. This is a nested attribute that contains the
* same attributes used with @NL80211_CMD_START_SCHED_SCAN. It
* specifies how the scan is performed (e.g. the interval, the
* channels to scan and the initial delay) as well as the scan
* results that will trigger a wake (i.e. the matchsets). This
* attribute is also sent in a response to
* @NL80211_CMD_GET_WIPHY, indicating the number of match sets
* supported by the driver (u32).
* @NL80211_WOWLAN_TRIG_NET_DETECT_RESULTS: nested attribute
* containing an array with information about what triggered the
* wake up. If no elements are present in the array, it means
* that the information is not available. If more than one
* element is present, it means that more than one match
* occurred.
* Each element in the array is a nested attribute that contains
* one optional %NL80211_ATTR_SSID attribute and one optional
* %NL80211_ATTR_SCAN_FREQUENCIES attribute. At least one of
* these attributes must be present. If
* %NL80211_ATTR_SCAN_FREQUENCIES contains more than one
* frequency, it means that the match occurred in more than one
* channel.
* @NUM_NL80211_WOWLAN_TRIG: number of wake on wireless triggers
* @MAX_NL80211_WOWLAN_TRIG: highest wowlan trigger attribute number
*
* These nested attributes are used to configure the wakeup triggers and
* to report the wakeup reason(s).
*/
enum nl80211_wowlan_triggers {
__NL80211_WOWLAN_TRIG_INVALID,
NL80211_WOWLAN_TRIG_ANY,
NL80211_WOWLAN_TRIG_DISCONNECT,
NL80211_WOWLAN_TRIG_MAGIC_PKT,
NL80211_WOWLAN_TRIG_PKT_PATTERN,
NL80211_WOWLAN_TRIG_GTK_REKEY_SUPPORTED,
NL80211_WOWLAN_TRIG_GTK_REKEY_FAILURE,
NL80211_WOWLAN_TRIG_EAP_IDENT_REQUEST,
NL80211_WOWLAN_TRIG_4WAY_HANDSHAKE,
NL80211_WOWLAN_TRIG_RFKILL_RELEASE,
NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211,
NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211_LEN,
NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023,
NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023_LEN,
NL80211_WOWLAN_TRIG_TCP_CONNECTION,
NL80211_WOWLAN_TRIG_WAKEUP_TCP_MATCH,
NL80211_WOWLAN_TRIG_WAKEUP_TCP_CONNLOST,
NL80211_WOWLAN_TRIG_WAKEUP_TCP_NOMORETOKENS,
NL80211_WOWLAN_TRIG_NET_DETECT,
NL80211_WOWLAN_TRIG_NET_DETECT_RESULTS,
/* keep last */
NUM_NL80211_WOWLAN_TRIG,
MAX_NL80211_WOWLAN_TRIG = NUM_NL80211_WOWLAN_TRIG - 1
};
/**
* DOC: TCP connection wakeup
*
* Some devices can establish a TCP connection in order to be woken up by a
* packet coming in from outside their network segment, or behind NAT. If
* configured, the device will establish a TCP connection to the given
* service, and periodically send data to that service. The first data
* packet is usually transmitted after SYN/ACK, also ACKing the SYN/ACK.
* The data packets can optionally include a (little endian) sequence
* number (in the TCP payload!) that is generated by the device, and, also
* optionally, a token from a list of tokens. This serves as a keep-alive
* with the service, and for NATed connections, etc.
*
* During this keep-alive period, the server doesn't send any data to the
* client. When receiving data, it is compared against the wakeup pattern
* (and mask) and if it matches, the host is woken up. Similarly, if the
* connection breaks or cannot be established to start with, the host is
* also woken up.
*
* Developer's note: ARP offload is required for this, otherwise TCP
* response packets might not go through correctly.
*/
/**
* struct nl80211_wowlan_tcp_data_seq - WoWLAN TCP data sequence
* @start: starting value
* @offset: offset of sequence number in packet
* @len: length of the sequence value to write, 1 through 4
*
* Note: don't confuse with the TCP sequence number(s), this is for the
* keepalive packet payload. The actual value is written into the packet
* in little endian.
*/
struct nl80211_wowlan_tcp_data_seq {
__u32 start, offset, len;
};
/**
* struct nl80211_wowlan_tcp_data_token - WoWLAN TCP data token config
* @offset: offset of token in packet
* @len: length of each token
* @token_stream: stream of data to be used for the tokens, the length must
* be a multiple of @len for this to make sense
*/
struct nl80211_wowlan_tcp_data_token {
__u32 offset, len;
__u8 token_stream[];
};
/**
* struct nl80211_wowlan_tcp_data_token_feature - data token features
* @min_len: minimum token length
* @max_len: maximum token length
* @bufsize: total available token buffer size (max size of @token_stream)
*/
struct nl80211_wowlan_tcp_data_token_feature {
__u32 min_len, max_len, bufsize;
};
/**
* enum nl80211_wowlan_tcp_attrs - WoWLAN TCP connection parameters
* @__NL80211_WOWLAN_TCP_INVALID: invalid number for nested attributes
* @NL80211_WOWLAN_TCP_SRC_IPV4: source IPv4 address (in network byte order)
* @NL80211_WOWLAN_TCP_DST_IPV4: destination IPv4 address
* (in network byte order)
* @NL80211_WOWLAN_TCP_DST_MAC: destination MAC address, this is given because
* route lookup when configured might be invalid by the time we suspend,
* and doing a route lookup when suspending is no longer possible as it
* might require ARP querying.
* @NL80211_WOWLAN_TCP_SRC_PORT: source port (u16); optional, if not given a
* socket and port will be allocated
* @NL80211_WOWLAN_TCP_DST_PORT: destination port (u16)
* @NL80211_WOWLAN_TCP_DATA_PAYLOAD: data packet payload, at least one byte.
* For feature advertising, a u32 attribute holding the maximum length
* of the data payload.
* @NL80211_WOWLAN_TCP_DATA_PAYLOAD_SEQ: data packet sequence configuration
* (if desired), a &struct nl80211_wowlan_tcp_data_seq. For feature
* advertising it is just a flag
* @NL80211_WOWLAN_TCP_DATA_PAYLOAD_TOKEN: data packet token configuration,
* see &struct nl80211_wowlan_tcp_data_token and for advertising see
* &struct nl80211_wowlan_tcp_data_token_feature.
* @NL80211_WOWLAN_TCP_DATA_INTERVAL: data interval in seconds, maximum
* interval in feature advertising (u32)
* @NL80211_WOWLAN_TCP_WAKE_PAYLOAD: wake packet payload, for advertising a
* u32 attribute holding the maximum length
* @NL80211_WOWLAN_TCP_WAKE_MASK: Wake packet payload mask, not used for
* feature advertising. The mask works like @NL80211_PKTPAT_MASK
* but on the TCP payload only.
* @NUM_NL80211_WOWLAN_TCP: number of TCP attributes
* @MAX_NL80211_WOWLAN_TCP: highest attribute number
*/
enum nl80211_wowlan_tcp_attrs {
__NL80211_WOWLAN_TCP_INVALID,
NL80211_WOWLAN_TCP_SRC_IPV4,
NL80211_WOWLAN_TCP_DST_IPV4,
NL80211_WOWLAN_TCP_DST_MAC,
NL80211_WOWLAN_TCP_SRC_PORT,
NL80211_WOWLAN_TCP_DST_PORT,
NL80211_WOWLAN_TCP_DATA_PAYLOAD,
NL80211_WOWLAN_TCP_DATA_PAYLOAD_SEQ,
NL80211_WOWLAN_TCP_DATA_PAYLOAD_TOKEN,
NL80211_WOWLAN_TCP_DATA_INTERVAL,
NL80211_WOWLAN_TCP_WAKE_PAYLOAD,
NL80211_WOWLAN_TCP_WAKE_MASK,
/* keep last */
NUM_NL80211_WOWLAN_TCP,
MAX_NL80211_WOWLAN_TCP = NUM_NL80211_WOWLAN_TCP - 1
};
/**
* struct nl80211_coalesce_rule_support - coalesce rule support information
* @max_rules: maximum number of rules supported
* @pat: packet pattern support information
* @max_delay: maximum supported coalescing delay in msecs
*
* This struct is carried in %NL80211_ATTR_COALESCE_RULE in the
* capability information given by the kernel to userspace.
*/
struct nl80211_coalesce_rule_support {
__u32 max_rules;
struct nl80211_pattern_support pat;
__u32 max_delay;
} __attribute__((packed));
/**
* enum nl80211_attr_coalesce_rule - coalesce rule attribute
* @__NL80211_COALESCE_RULE_INVALID: invalid number for nested attribute
* @NL80211_ATTR_COALESCE_RULE_DELAY: delay in msecs used for packet coalescing
* @NL80211_ATTR_COALESCE_RULE_CONDITION: condition for packet coalescence,
* see &enum nl80211_coalesce_condition.
* @NL80211_ATTR_COALESCE_RULE_PKT_PATTERN: packet offset, pattern is matched
* after these fixed number of bytes of received packet
* @NUM_NL80211_ATTR_COALESCE_RULE: number of attributes
* @NL80211_ATTR_COALESCE_RULE_MAX: max attribute number
*/
enum nl80211_attr_coalesce_rule {
__NL80211_COALESCE_RULE_INVALID,
NL80211_ATTR_COALESCE_RULE_DELAY,
NL80211_ATTR_COALESCE_RULE_CONDITION,
NL80211_ATTR_COALESCE_RULE_PKT_PATTERN,
/* keep last */
NUM_NL80211_ATTR_COALESCE_RULE,
NL80211_ATTR_COALESCE_RULE_MAX = NUM_NL80211_ATTR_COALESCE_RULE - 1
};
/**
* enum nl80211_coalesce_condition - coalesce rule conditions
* @NL80211_COALESCE_CONDITION_MATCH: coalaesce Rx packets when patterns
* in a rule are matched.
* @NL80211_COALESCE_CONDITION_NO_MATCH: coalesce Rx packets when patterns
* in a rule are not matched.
*/
enum nl80211_coalesce_condition {
NL80211_COALESCE_CONDITION_MATCH,
NL80211_COALESCE_CONDITION_NO_MATCH
};
/**
* enum nl80211_iface_limit_attrs - limit attributes
* @NL80211_IFACE_LIMIT_UNSPEC: (reserved)
* @NL80211_IFACE_LIMIT_MAX: maximum number of interfaces that
* can be chosen from this set of interface types (u32)
* @NL80211_IFACE_LIMIT_TYPES: nested attribute containing a
* flag attribute for each interface type in this set
* @NUM_NL80211_IFACE_LIMIT: number of attributes
* @MAX_NL80211_IFACE_LIMIT: highest attribute number
*/
enum nl80211_iface_limit_attrs {
NL80211_IFACE_LIMIT_UNSPEC,
NL80211_IFACE_LIMIT_MAX,
NL80211_IFACE_LIMIT_TYPES,
/* keep last */
NUM_NL80211_IFACE_LIMIT,
MAX_NL80211_IFACE_LIMIT = NUM_NL80211_IFACE_LIMIT - 1
};
/**
* enum nl80211_if_combination_attrs -- interface combination attributes
*
* @NL80211_IFACE_COMB_UNSPEC: (reserved)
* @NL80211_IFACE_COMB_LIMITS: Nested attributes containing the limits
* for given interface types, see &enum nl80211_iface_limit_attrs.
* @NL80211_IFACE_COMB_MAXNUM: u32 attribute giving the total number of
* interfaces that can be created in this group. This number doesn't
* apply to interfaces purely managed in software, which are listed
* in a separate attribute %NL80211_ATTR_INTERFACES_SOFTWARE.
* @NL80211_IFACE_COMB_STA_AP_BI_MATCH: flag attribute specifying that
* beacon intervals within this group must be all the same even for
* infrastructure and AP/GO combinations, i.e. the GO(s) must adopt
* the infrastructure network's beacon interval.
* @NL80211_IFACE_COMB_NUM_CHANNELS: u32 attribute specifying how many
* different channels may be used within this group.
* @NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS: u32 attribute containing the bitmap
* of supported channel widths for radar detection.
* @NL80211_IFACE_COMB_RADAR_DETECT_REGIONS: u32 attribute containing the bitmap
* of supported regulatory regions for radar detection.
* @NL80211_IFACE_COMB_BI_MIN_GCD: u32 attribute specifying the minimum GCD of
* different beacon intervals supported by all the interface combinations
* in this group (if not present, all beacon intervals be identical).
* @NUM_NL80211_IFACE_COMB: number of attributes
* @MAX_NL80211_IFACE_COMB: highest attribute number
*
* Examples:
* limits = [ #{STA} <= 1, #{AP} <= 1 ], matching BI, channels = 1, max = 2
* => allows an AP and a STA that must match BIs
*
* numbers = [ #{AP, P2P-GO} <= 8 ], BI min gcd, channels = 1, max = 8,
* => allows 8 of AP/GO that can have BI gcd >= min gcd
*
* numbers = [ #{STA} <= 2 ], channels = 2, max = 2
* => allows two STAs on the same or on different channels
*
* numbers = [ #{STA} <= 1, #{P2P-client,P2P-GO} <= 3 ], max = 4
* => allows a STA plus three P2P interfaces
*
* The list of these four possibilities could completely be contained
* within the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute to indicate
* that any of these groups must match.
*
* "Combinations" of just a single interface will not be listed here,
* a single interface of any valid interface type is assumed to always
* be possible by itself. This means that implicitly, for each valid
* interface type, the following group always exists:
* numbers = [ #{<type>} <= 1 ], channels = 1, max = 1
*/
enum nl80211_if_combination_attrs {
NL80211_IFACE_COMB_UNSPEC,
NL80211_IFACE_COMB_LIMITS,
NL80211_IFACE_COMB_MAXNUM,
NL80211_IFACE_COMB_STA_AP_BI_MATCH,
NL80211_IFACE_COMB_NUM_CHANNELS,
NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS,
NL80211_IFACE_COMB_RADAR_DETECT_REGIONS,
NL80211_IFACE_COMB_BI_MIN_GCD,
/* keep last */
NUM_NL80211_IFACE_COMB,
MAX_NL80211_IFACE_COMB = NUM_NL80211_IFACE_COMB - 1
};
/**
* enum nl80211_plink_state - state of a mesh peer link finite state machine
*
* @NL80211_PLINK_LISTEN: initial state, considered the implicit
* state of non existent mesh peer links
* @NL80211_PLINK_OPN_SNT: mesh plink open frame has been sent to
* this mesh peer
* @NL80211_PLINK_OPN_RCVD: mesh plink open frame has been received
* from this mesh peer
* @NL80211_PLINK_CNF_RCVD: mesh plink confirm frame has been
* received from this mesh peer
* @NL80211_PLINK_ESTAB: mesh peer link is established
* @NL80211_PLINK_HOLDING: mesh peer link is being closed or cancelled
* @NL80211_PLINK_BLOCKED: all frames transmitted from this mesh
* plink are discarded, except for authentication frames
* @NUM_NL80211_PLINK_STATES: number of peer link states
* @MAX_NL80211_PLINK_STATES: highest numerical value of plink states
*/
enum nl80211_plink_state {
NL80211_PLINK_LISTEN,
NL80211_PLINK_OPN_SNT,
NL80211_PLINK_OPN_RCVD,
NL80211_PLINK_CNF_RCVD,
NL80211_PLINK_ESTAB,
NL80211_PLINK_HOLDING,
NL80211_PLINK_BLOCKED,
/* keep last */
NUM_NL80211_PLINK_STATES,
MAX_NL80211_PLINK_STATES = NUM_NL80211_PLINK_STATES - 1
};
/**
* enum nl80211_plink_action - actions to perform in mesh peers
*
* @NL80211_PLINK_ACTION_NO_ACTION: perform no action
* @NL80211_PLINK_ACTION_OPEN: start mesh peer link establishment
* @NL80211_PLINK_ACTION_BLOCK: block traffic from this mesh peer
* @NUM_NL80211_PLINK_ACTIONS: number of possible actions
*/
enum plink_actions {
NL80211_PLINK_ACTION_NO_ACTION,
NL80211_PLINK_ACTION_OPEN,
NL80211_PLINK_ACTION_BLOCK,
NUM_NL80211_PLINK_ACTIONS,
};
#define NL80211_KCK_LEN 16
#define NL80211_KEK_LEN 16
#define NL80211_KCK_EXT_LEN 24
#define NL80211_KEK_EXT_LEN 32
#define NL80211_KCK_EXT_LEN_32 32
#define NL80211_REPLAY_CTR_LEN 8
/**
* enum nl80211_rekey_data - attributes for GTK rekey offload
* @__NL80211_REKEY_DATA_INVALID: invalid number for nested attributes
* @NL80211_REKEY_DATA_KEK: key encryption key (binary)
* @NL80211_REKEY_DATA_KCK: key confirmation key (binary)
* @NL80211_REKEY_DATA_REPLAY_CTR: replay counter (binary)
* @NL80211_REKEY_DATA_AKM: AKM data (OUI, suite type)
* @NUM_NL80211_REKEY_DATA: number of rekey attributes (internal)
* @MAX_NL80211_REKEY_DATA: highest rekey attribute (internal)
*/
enum nl80211_rekey_data {
__NL80211_REKEY_DATA_INVALID,
NL80211_REKEY_DATA_KEK,
NL80211_REKEY_DATA_KCK,
NL80211_REKEY_DATA_REPLAY_CTR,
NL80211_REKEY_DATA_AKM,
/* keep last */
NUM_NL80211_REKEY_DATA,
MAX_NL80211_REKEY_DATA = NUM_NL80211_REKEY_DATA - 1
};
/**
* enum nl80211_hidden_ssid - values for %NL80211_ATTR_HIDDEN_SSID
* @NL80211_HIDDEN_SSID_NOT_IN_USE: do not hide SSID (i.e., broadcast it in
* Beacon frames)
* @NL80211_HIDDEN_SSID_ZERO_LEN: hide SSID by using zero-length SSID element
* in Beacon frames
* @NL80211_HIDDEN_SSID_ZERO_CONTENTS: hide SSID by using correct length of SSID
* element in Beacon frames but zero out each byte in the SSID
*/
enum nl80211_hidden_ssid {
NL80211_HIDDEN_SSID_NOT_IN_USE,
NL80211_HIDDEN_SSID_ZERO_LEN,
NL80211_HIDDEN_SSID_ZERO_CONTENTS
};
/**
* enum nl80211_sta_wme_attr - station WME attributes
* @__NL80211_STA_WME_INVALID: invalid number for nested attribute
* @NL80211_STA_WME_UAPSD_QUEUES: bitmap of uapsd queues. the format
* is the same as the AC bitmap in the QoS info field.
* @NL80211_STA_WME_MAX_SP: max service period. the format is the same
* as the MAX_SP field in the QoS info field (but already shifted down).
* @__NL80211_STA_WME_AFTER_LAST: internal
* @NL80211_STA_WME_MAX: highest station WME attribute
*/
enum nl80211_sta_wme_attr {
__NL80211_STA_WME_INVALID,
NL80211_STA_WME_UAPSD_QUEUES,
NL80211_STA_WME_MAX_SP,
/* keep last */
__NL80211_STA_WME_AFTER_LAST,
NL80211_STA_WME_MAX = __NL80211_STA_WME_AFTER_LAST - 1
};
/**
* enum nl80211_pmksa_candidate_attr - attributes for PMKSA caching candidates
* @__NL80211_PMKSA_CANDIDATE_INVALID: invalid number for nested attributes
* @NL80211_PMKSA_CANDIDATE_INDEX: candidate index (u32; the smaller, the higher
* priority)
* @NL80211_PMKSA_CANDIDATE_BSSID: candidate BSSID (6 octets)
* @NL80211_PMKSA_CANDIDATE_PREAUTH: RSN pre-authentication supported (flag)
* @NUM_NL80211_PMKSA_CANDIDATE: number of PMKSA caching candidate attributes
* (internal)
* @MAX_NL80211_PMKSA_CANDIDATE: highest PMKSA caching candidate attribute
* (internal)
*/
enum nl80211_pmksa_candidate_attr {
__NL80211_PMKSA_CANDIDATE_INVALID,
NL80211_PMKSA_CANDIDATE_INDEX,
NL80211_PMKSA_CANDIDATE_BSSID,
NL80211_PMKSA_CANDIDATE_PREAUTH,
/* keep last */
NUM_NL80211_PMKSA_CANDIDATE,
MAX_NL80211_PMKSA_CANDIDATE = NUM_NL80211_PMKSA_CANDIDATE - 1
};
/**
* enum nl80211_tdls_operation - values for %NL80211_ATTR_TDLS_OPERATION
* @NL80211_TDLS_DISCOVERY_REQ: Send a TDLS discovery request
* @NL80211_TDLS_SETUP: Setup TDLS link
* @NL80211_TDLS_TEARDOWN: Teardown a TDLS link which is already established
* @NL80211_TDLS_ENABLE_LINK: Enable TDLS link
* @NL80211_TDLS_DISABLE_LINK: Disable TDLS link
*/
enum nl80211_tdls_operation {
NL80211_TDLS_DISCOVERY_REQ,
NL80211_TDLS_SETUP,
NL80211_TDLS_TEARDOWN,
NL80211_TDLS_ENABLE_LINK,
NL80211_TDLS_DISABLE_LINK,
};
/**
* enum nl80211_ap_sme_features - device-integrated AP features
* @NL80211_AP_SME_SA_QUERY_OFFLOAD: SA Query procedures offloaded to driver
* when user space indicates support for SA Query procedures offload during
* "start ap" with %NL80211_AP_SETTINGS_SA_QUERY_OFFLOAD_SUPPORT.
*/
enum nl80211_ap_sme_features {
NL80211_AP_SME_SA_QUERY_OFFLOAD = 1 << 0,
};
/**
* enum nl80211_feature_flags - device/driver features
* @NL80211_FEATURE_SK_TX_STATUS: This driver supports reflecting back
* TX status to the socket error queue when requested with the
* socket option.
* @NL80211_FEATURE_HT_IBSS: This driver supports IBSS with HT datarates.
* @NL80211_FEATURE_INACTIVITY_TIMER: This driver takes care of freeing up
* the connected inactive stations in AP mode.
* @NL80211_FEATURE_CELL_BASE_REG_HINTS: This driver has been tested
* to work properly to support receiving regulatory hints from
* cellular base stations.
* @NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL: (no longer available, only
* here to reserve the value for API/ABI compatibility)
* @NL80211_FEATURE_SAE: This driver supports simultaneous authentication of
* equals (SAE) with user space SME (NL80211_CMD_AUTHENTICATE) in station
* mode
* @NL80211_FEATURE_LOW_PRIORITY_SCAN: This driver supports low priority scan
* @NL80211_FEATURE_SCAN_FLUSH: Scan flush is supported
* @NL80211_FEATURE_AP_SCAN: Support scanning using an AP vif
* @NL80211_FEATURE_VIF_TXPOWER: The driver supports per-vif TX power setting
* @NL80211_FEATURE_NEED_OBSS_SCAN: The driver expects userspace to perform
* OBSS scans and generate 20/40 BSS coex reports. This flag is used only
* for drivers implementing the CONNECT API, for AUTH/ASSOC it is implied.
* @NL80211_FEATURE_P2P_GO_CTWIN: P2P GO implementation supports CT Window
* setting
* @NL80211_FEATURE_P2P_GO_OPPPS: P2P GO implementation supports opportunistic
* powersave
* @NL80211_FEATURE_FULL_AP_CLIENT_STATE: The driver supports full state
* transitions for AP clients. Without this flag (and if the driver
* doesn't have the AP SME in the device) the driver supports adding
* stations only when they're associated and adds them in associated
* state (to later be transitioned into authorized), with this flag
* they should be added before even sending the authentication reply
* and then transitioned into authenticated, associated and authorized
* states using station flags.
* Note that even for drivers that support this, the default is to add
* stations in authenticated/associated state, so to add unauthenticated
* stations the authenticated/associated bits have to be set in the mask.
* @NL80211_FEATURE_ADVERTISE_CHAN_LIMITS: cfg80211 advertises channel limits
* (HT40, VHT 80/160 MHz) if this flag is set
* @NL80211_FEATURE_USERSPACE_MPM: This driver supports a userspace Mesh
* Peering Management entity which may be implemented by registering for
* beacons or NL80211_CMD_NEW_PEER_CANDIDATE events. The mesh beacon is
* still generated by the driver.
* @NL80211_FEATURE_ACTIVE_MONITOR: This driver supports an active monitor
* interface. An active monitor interface behaves like a normal monitor
* interface, but gets added to the driver. It ensures that incoming
* unicast packets directed at the configured interface address get ACKed.
* @NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE: This driver supports dynamic
* channel bandwidth change (e.g., HT 20 <-> 40 MHz channel) during the
* lifetime of a BSS.
* @NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES: This device adds a DS Parameter
* Set IE to probe requests.
* @NL80211_FEATURE_WFA_TPC_IE_IN_PROBES: This device adds a WFA TPC Report IE
* to probe requests.
* @NL80211_FEATURE_QUIET: This device, in client mode, supports Quiet Period
* requests sent to it by an AP.
* @NL80211_FEATURE_TX_POWER_INSERTION: This device is capable of inserting the
* current tx power value into the TPC Report IE in the spectrum
* management TPC Report action frame, and in the Radio Measurement Link
* Measurement Report action frame.
* @NL80211_FEATURE_ACKTO_ESTIMATION: This driver supports dynamic ACK timeout
* estimation (dynack). %NL80211_ATTR_WIPHY_DYN_ACK flag attribute is used
* to enable dynack.
* @NL80211_FEATURE_STATIC_SMPS: Device supports static spatial
* multiplexing powersave, ie. can turn off all but one chain
* even on HT connections that should be using more chains.
* @NL80211_FEATURE_DYNAMIC_SMPS: Device supports dynamic spatial
* multiplexing powersave, ie. can turn off all but one chain
* and then wake the rest up as required after, for example,
* rts/cts handshake.
* @NL80211_FEATURE_SUPPORTS_WMM_ADMISSION: the device supports setting up WMM
* TSPEC sessions (TID aka TSID 0-7) with the %NL80211_CMD_ADD_TX_TS
* command. Standard IEEE 802.11 TSPEC setup is not yet supported, it
* needs to be able to handle Block-Ack agreements and other things.
* @NL80211_FEATURE_MAC_ON_CREATE: Device supports configuring
* the vif's MAC address upon creation.
* See 'macaddr' field in the vif_params (cfg80211.h).
* @NL80211_FEATURE_TDLS_CHANNEL_SWITCH: Driver supports channel switching when
* operating as a TDLS peer.
* @NL80211_FEATURE_SCAN_RANDOM_MAC_ADDR: This device/driver supports using a
* random MAC address during scan (if the device is unassociated); the
* %NL80211_SCAN_FLAG_RANDOM_ADDR flag may be set for scans and the MAC
* address mask/value will be used.
* @NL80211_FEATURE_SCHED_SCAN_RANDOM_MAC_ADDR: This device/driver supports
* using a random MAC address for every scan iteration during scheduled
* scan (while not associated), the %NL80211_SCAN_FLAG_RANDOM_ADDR may
* be set for scheduled scan and the MAC address mask/value will be used.
* @NL80211_FEATURE_ND_RANDOM_MAC_ADDR: This device/driver supports using a
* random MAC address for every scan iteration during "net detect", i.e.
* scan in unassociated WoWLAN, the %NL80211_SCAN_FLAG_RANDOM_ADDR may
* be set for scheduled scan and the MAC address mask/value will be used.
*/
enum nl80211_feature_flags {
NL80211_FEATURE_SK_TX_STATUS = 1 << 0,
NL80211_FEATURE_HT_IBSS = 1 << 1,
NL80211_FEATURE_INACTIVITY_TIMER = 1 << 2,
NL80211_FEATURE_CELL_BASE_REG_HINTS = 1 << 3,
NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL = 1 << 4,
NL80211_FEATURE_SAE = 1 << 5,
NL80211_FEATURE_LOW_PRIORITY_SCAN = 1 << 6,
NL80211_FEATURE_SCAN_FLUSH = 1 << 7,
NL80211_FEATURE_AP_SCAN = 1 << 8,
NL80211_FEATURE_VIF_TXPOWER = 1 << 9,
NL80211_FEATURE_NEED_OBSS_SCAN = 1 << 10,
NL80211_FEATURE_P2P_GO_CTWIN = 1 << 11,
NL80211_FEATURE_P2P_GO_OPPPS = 1 << 12,
/* bit 13 is reserved */
NL80211_FEATURE_ADVERTISE_CHAN_LIMITS = 1 << 14,
NL80211_FEATURE_FULL_AP_CLIENT_STATE = 1 << 15,
NL80211_FEATURE_USERSPACE_MPM = 1 << 16,
NL80211_FEATURE_ACTIVE_MONITOR = 1 << 17,
NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE = 1 << 18,
NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES = 1 << 19,
NL80211_FEATURE_WFA_TPC_IE_IN_PROBES = 1 << 20,
NL80211_FEATURE_QUIET = 1 << 21,
NL80211_FEATURE_TX_POWER_INSERTION = 1 << 22,
NL80211_FEATURE_ACKTO_ESTIMATION = 1 << 23,
NL80211_FEATURE_STATIC_SMPS = 1 << 24,
NL80211_FEATURE_DYNAMIC_SMPS = 1 << 25,
NL80211_FEATURE_SUPPORTS_WMM_ADMISSION = 1 << 26,
NL80211_FEATURE_MAC_ON_CREATE = 1 << 27,
NL80211_FEATURE_TDLS_CHANNEL_SWITCH = 1 << 28,
NL80211_FEATURE_SCAN_RANDOM_MAC_ADDR = 1 << 29,
NL80211_FEATURE_SCHED_SCAN_RANDOM_MAC_ADDR = 1 << 30,
NL80211_FEATURE_ND_RANDOM_MAC_ADDR = 1 << 31,
};
/**
* enum nl80211_ext_feature_index - bit index of extended features.
* @NL80211_EXT_FEATURE_VHT_IBSS: This driver supports IBSS with VHT datarates.
* @NL80211_EXT_FEATURE_RRM: This driver supports RRM. When featured, user can
* request to use RRM (see %NL80211_ATTR_USE_RRM) with
* %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests, which will set
* the ASSOC_REQ_USE_RRM flag in the association request even if
* NL80211_FEATURE_QUIET is not advertized.
* @NL80211_EXT_FEATURE_MU_MIMO_AIR_SNIFFER: This device supports MU-MIMO air
* sniffer which means that it can be configured to hear packets from
* certain groups which can be configured by the
* %NL80211_ATTR_MU_MIMO_GROUP_DATA attribute,
* or can be configured to follow a station by configuring the
* %NL80211_ATTR_MU_MIMO_FOLLOW_MAC_ADDR attribute.
* @NL80211_EXT_FEATURE_SCAN_START_TIME: This driver includes the actual
* time the scan started in scan results event. The time is the TSF of
* the BSS that the interface that requested the scan is connected to
* (if available).
* @NL80211_EXT_FEATURE_BSS_PARENT_TSF: Per BSS, this driver reports the
* time the last beacon/probe was received. The time is the TSF of the
* BSS that the interface that requested the scan is connected to
* (if available).
* @NL80211_EXT_FEATURE_SET_SCAN_DWELL: This driver supports configuration of
* channel dwell time.
* @NL80211_EXT_FEATURE_BEACON_RATE_LEGACY: Driver supports beacon rate
* configuration (AP/mesh), supporting a legacy (non HT/VHT) rate.
* @NL80211_EXT_FEATURE_BEACON_RATE_HT: Driver supports beacon rate
* configuration (AP/mesh) with HT rates.
* @NL80211_EXT_FEATURE_BEACON_RATE_VHT: Driver supports beacon rate
* configuration (AP/mesh) with VHT rates.
* @NL80211_EXT_FEATURE_FILS_STA: This driver supports Fast Initial Link Setup
* with user space SME (NL80211_CMD_AUTHENTICATE) in station mode.
* @NL80211_EXT_FEATURE_MGMT_TX_RANDOM_TA: This driver supports randomized TA
* in @NL80211_CMD_FRAME while not associated.
* @NL80211_EXT_FEATURE_MGMT_TX_RANDOM_TA_CONNECTED: This driver supports
* randomized TA in @NL80211_CMD_FRAME while associated.
* @NL80211_EXT_FEATURE_SCHED_SCAN_RELATIVE_RSSI: The driver supports sched_scan
* for reporting BSSs with better RSSI than the current connected BSS
* (%NL80211_ATTR_SCHED_SCAN_RELATIVE_RSSI).
* @NL80211_EXT_FEATURE_CQM_RSSI_LIST: With this driver the
* %NL80211_ATTR_CQM_RSSI_THOLD attribute accepts a list of zero or more
* RSSI threshold values to monitor rather than exactly one threshold.
* @NL80211_EXT_FEATURE_FILS_SK_OFFLOAD: Driver SME supports FILS shared key
* authentication with %NL80211_CMD_CONNECT.
* @NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_PSK: Device wants to do 4-way
* handshake with PSK in station mode (PSK is passed as part of the connect
* and associate commands), doing it in the host might not be supported.
* @NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_1X: Device wants to do doing 4-way
* handshake with 802.1X in station mode (will pass EAP frames to the host
* and accept the set_pmk/del_pmk commands), doing it in the host might not
* be supported.
* @NL80211_EXT_FEATURE_FILS_MAX_CHANNEL_TIME: Driver is capable of overriding
* the max channel attribute in the FILS request params IE with the
* actual dwell time.
* @NL80211_EXT_FEATURE_ACCEPT_BCAST_PROBE_RESP: Driver accepts broadcast probe
* response
* @NL80211_EXT_FEATURE_OCE_PROBE_REQ_HIGH_TX_RATE: Driver supports sending
* the first probe request in each channel at rate of at least 5.5Mbps.
* @NL80211_EXT_FEATURE_OCE_PROBE_REQ_DEFERRAL_SUPPRESSION: Driver supports
* probe request tx deferral and suppression
* @NL80211_EXT_FEATURE_MFP_OPTIONAL: Driver supports the %NL80211_MFP_OPTIONAL
* value in %NL80211_ATTR_USE_MFP.
* @NL80211_EXT_FEATURE_LOW_SPAN_SCAN: Driver supports low span scan.
* @NL80211_EXT_FEATURE_LOW_POWER_SCAN: Driver supports low power scan.
* @NL80211_EXT_FEATURE_HIGH_ACCURACY_SCAN: Driver supports high accuracy scan.
* @NL80211_EXT_FEATURE_DFS_OFFLOAD: HW/driver will offload DFS actions.
* Device or driver will do all DFS-related actions by itself,
* informing user-space about CAC progress, radar detection event,
* channel change triggered by radar detection event.
* No need to start CAC from user-space, no need to react to
* "radar detected" event.
* @NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211: Driver supports sending and
* receiving control port frames over nl80211 instead of the netdevice.
* @NL80211_EXT_FEATURE_ACK_SIGNAL_SUPPORT: This driver/device supports
* (average) ACK signal strength reporting.
* @NL80211_EXT_FEATURE_TXQS: Driver supports FQ-CoDel-enabled intermediate
* TXQs.
* @NL80211_EXT_FEATURE_SCAN_RANDOM_SN: Driver/device supports randomizing the
* SN in probe request frames if requested by %NL80211_SCAN_FLAG_RANDOM_SN.
* @NL80211_EXT_FEATURE_SCAN_MIN_PREQ_CONTENT: Driver/device can omit all data
* except for supported rates from the probe request content if requested
* by the %NL80211_SCAN_FLAG_MIN_PREQ_CONTENT flag.
* @NL80211_EXT_FEATURE_ENABLE_FTM_RESPONDER: Driver supports enabling fine
* timing measurement responder role.
*
* @NL80211_EXT_FEATURE_CAN_REPLACE_PTK0: Driver/device confirm that they are
* able to rekey an in-use key correctly. Userspace must not rekey PTK keys
* if this flag is not set. Ignoring this can leak clear text packets and/or
* freeze the connection.
* @NL80211_EXT_FEATURE_EXT_KEY_ID: Driver supports "Extended Key ID for
* Individually Addressed Frames" from IEEE802.11-2016.
*
* @NL80211_EXT_FEATURE_AIRTIME_FAIRNESS: Driver supports getting airtime
* fairness for transmitted packets and has enabled airtime fairness
* scheduling.
*
* @NL80211_EXT_FEATURE_AP_PMKSA_CACHING: Driver/device supports PMKSA caching
* (set/del PMKSA operations) in AP mode.
*
* @NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD: Driver supports
* filtering of sched scan results using band specific RSSI thresholds.
*
* @NL80211_EXT_FEATURE_STA_TX_PWR: This driver supports controlling tx power
* to a station.
*
* @NL80211_EXT_FEATURE_SAE_OFFLOAD: Device wants to do SAE authentication in
* station mode (SAE password is passed as part of the connect command).
*
* @NL80211_EXT_FEATURE_VLAN_OFFLOAD: The driver supports a single netdev
* with VLAN tagged frames and separate VLAN-specific netdevs added using
* vconfig similarly to the Ethernet case.
*
* @NL80211_EXT_FEATURE_AQL: The driver supports the Airtime Queue Limit (AQL)
* feature, which prevents bufferbloat by using the expected transmission
* time to limit the amount of data buffered in the hardware.
*
* @NL80211_EXT_FEATURE_BEACON_PROTECTION: The driver supports Beacon protection
* and can receive key configuration for BIGTK using key indexes 6 and 7.
* @NL80211_EXT_FEATURE_BEACON_PROTECTION_CLIENT: The driver supports Beacon
* protection as a client only and cannot transmit protected beacons.
*
* @NL80211_EXT_FEATURE_CONTROL_PORT_NO_PREAUTH: The driver can disable the
* forwarding of preauth frames over the control port. They are then
* handled as ordinary data frames.
*
* @NL80211_EXT_FEATURE_PROTECTED_TWT: Driver supports protected TWT frames
*
* @NL80211_EXT_FEATURE_DEL_IBSS_STA: The driver supports removing stations
* in IBSS mode, essentially by dropping their state.
*
* @NL80211_EXT_FEATURE_MULTICAST_REGISTRATIONS: management frame registrations
* are possible for multicast frames and those will be reported properly.
*
* @NL80211_EXT_FEATURE_SCAN_FREQ_KHZ: This driver supports receiving and
* reporting scan request with %NL80211_ATTR_SCAN_FREQ_KHZ. In order to
* report %NL80211_ATTR_SCAN_FREQ_KHZ, %NL80211_SCAN_FLAG_FREQ_KHZ must be
* included in the scan request.
*
* @NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211_TX_STATUS: The driver
* can report tx status for control port over nl80211 tx operations.
*
* @NL80211_EXT_FEATURE_OPERATING_CHANNEL_VALIDATION: Driver supports Operating
* Channel Validation (OCV) when using driver's SME for RSNA handshakes.
*
* @NL80211_EXT_FEATURE_4WAY_HANDSHAKE_AP_PSK: Device wants to do 4-way
* handshake with PSK in AP mode (PSK is passed as part of the start AP
* command).
*
* @NL80211_EXT_FEATURE_SAE_OFFLOAD_AP: Device wants to do SAE authentication
* in AP mode (SAE password is passed as part of the start AP command).
*
* @NL80211_EXT_FEATURE_FILS_DISCOVERY: Driver/device supports FILS discovery
* frames transmission
*
* @NL80211_EXT_FEATURE_UNSOL_BCAST_PROBE_RESP: Driver/device supports
* unsolicited broadcast probe response transmission
*
* @NL80211_EXT_FEATURE_BEACON_RATE_HE: Driver supports beacon rate
* configuration (AP/mesh) with HE rates.
*
* @NL80211_EXT_FEATURE_SECURE_LTF: Device supports secure LTF measurement
* exchange protocol.
*
* @NL80211_EXT_FEATURE_SECURE_RTT: Device supports secure RTT measurement
* exchange protocol.
*
* @NL80211_EXT_FEATURE_PROT_RANGE_NEGO_AND_MEASURE: Device supports management
* frame protection for all management frames exchanged during the
* negotiation and range measurement procedure.
*
* @NL80211_EXT_FEATURE_BSS_COLOR: The driver supports BSS color collision
* detection and change announcemnts.
*
* @NL80211_EXT_FEATURE_FILS_CRYPTO_OFFLOAD: Driver running in AP mode supports
* FILS encryption and decryption for (Re)Association Request and Response
* frames. Userspace has to share FILS AAD details to the driver by using
* @NL80211_CMD_SET_FILS_AAD.
*
* @NL80211_EXT_FEATURE_RADAR_BACKGROUND: Device supports background radar/CAC
* detection.
*
* @NL80211_EXT_FEATURE_POWERED_ADDR_CHANGE: Device can perform a MAC address
* change without having to bring the underlying network device down
* first. For example, in station mode this can be used to vary the
* origin MAC address prior to a connection to a new AP for privacy
* or other reasons. Note that certain driver specific restrictions
* might apply, e.g. no scans in progress, no offchannel operations
* in progress, and no active connections.
*
* @NL80211_EXT_FEATURE_PUNCT: Driver supports preamble puncturing in AP mode.
*
* @NL80211_EXT_FEATURE_SECURE_NAN: Device supports NAN Pairing which enables
* authentication, data encryption and message integrity.
*
* @NL80211_EXT_FEATURE_AUTH_AND_DEAUTH_RANDOM_TA: Device supports randomized TA
* in authentication and deauthentication frames sent to unassociated peer
* using @NL80211_CMD_FRAME.
*
* @NUM_NL80211_EXT_FEATURES: number of extended features.
* @MAX_NL80211_EXT_FEATURES: highest extended feature index.
*/
enum nl80211_ext_feature_index {
NL80211_EXT_FEATURE_VHT_IBSS,
NL80211_EXT_FEATURE_RRM,
NL80211_EXT_FEATURE_MU_MIMO_AIR_SNIFFER,
NL80211_EXT_FEATURE_SCAN_START_TIME,
NL80211_EXT_FEATURE_BSS_PARENT_TSF,
NL80211_EXT_FEATURE_SET_SCAN_DWELL,
NL80211_EXT_FEATURE_BEACON_RATE_LEGACY,
NL80211_EXT_FEATURE_BEACON_RATE_HT,
NL80211_EXT_FEATURE_BEACON_RATE_VHT,
NL80211_EXT_FEATURE_FILS_STA,
NL80211_EXT_FEATURE_MGMT_TX_RANDOM_TA,
NL80211_EXT_FEATURE_MGMT_TX_RANDOM_TA_CONNECTED,
NL80211_EXT_FEATURE_SCHED_SCAN_RELATIVE_RSSI,
NL80211_EXT_FEATURE_CQM_RSSI_LIST,
NL80211_EXT_FEATURE_FILS_SK_OFFLOAD,
NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_PSK,
NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_1X,
NL80211_EXT_FEATURE_FILS_MAX_CHANNEL_TIME,
NL80211_EXT_FEATURE_ACCEPT_BCAST_PROBE_RESP,
NL80211_EXT_FEATURE_OCE_PROBE_REQ_HIGH_TX_RATE,
NL80211_EXT_FEATURE_OCE_PROBE_REQ_DEFERRAL_SUPPRESSION,
NL80211_EXT_FEATURE_MFP_OPTIONAL,
NL80211_EXT_FEATURE_LOW_SPAN_SCAN,
NL80211_EXT_FEATURE_LOW_POWER_SCAN,
NL80211_EXT_FEATURE_HIGH_ACCURACY_SCAN,
NL80211_EXT_FEATURE_DFS_OFFLOAD,
NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211,
NL80211_EXT_FEATURE_ACK_SIGNAL_SUPPORT,
/* we renamed this - stay compatible */
NL80211_EXT_FEATURE_DATA_ACK_SIGNAL_SUPPORT = NL80211_EXT_FEATURE_ACK_SIGNAL_SUPPORT,
NL80211_EXT_FEATURE_TXQS,
NL80211_EXT_FEATURE_SCAN_RANDOM_SN,
NL80211_EXT_FEATURE_SCAN_MIN_PREQ_CONTENT,
NL80211_EXT_FEATURE_CAN_REPLACE_PTK0,
NL80211_EXT_FEATURE_ENABLE_FTM_RESPONDER,
NL80211_EXT_FEATURE_AIRTIME_FAIRNESS,
NL80211_EXT_FEATURE_AP_PMKSA_CACHING,
NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD,
NL80211_EXT_FEATURE_EXT_KEY_ID,
NL80211_EXT_FEATURE_STA_TX_PWR,
NL80211_EXT_FEATURE_SAE_OFFLOAD,
NL80211_EXT_FEATURE_VLAN_OFFLOAD,
NL80211_EXT_FEATURE_AQL,
NL80211_EXT_FEATURE_BEACON_PROTECTION,
NL80211_EXT_FEATURE_CONTROL_PORT_NO_PREAUTH,
NL80211_EXT_FEATURE_PROTECTED_TWT,
NL80211_EXT_FEATURE_DEL_IBSS_STA,
NL80211_EXT_FEATURE_MULTICAST_REGISTRATIONS,
NL80211_EXT_FEATURE_BEACON_PROTECTION_CLIENT,
NL80211_EXT_FEATURE_SCAN_FREQ_KHZ,
NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211_TX_STATUS,
NL80211_EXT_FEATURE_OPERATING_CHANNEL_VALIDATION,
NL80211_EXT_FEATURE_4WAY_HANDSHAKE_AP_PSK,
NL80211_EXT_FEATURE_SAE_OFFLOAD_AP,
NL80211_EXT_FEATURE_FILS_DISCOVERY,
NL80211_EXT_FEATURE_UNSOL_BCAST_PROBE_RESP,
NL80211_EXT_FEATURE_BEACON_RATE_HE,
NL80211_EXT_FEATURE_SECURE_LTF,
NL80211_EXT_FEATURE_SECURE_RTT,
NL80211_EXT_FEATURE_PROT_RANGE_NEGO_AND_MEASURE,
NL80211_EXT_FEATURE_BSS_COLOR,
NL80211_EXT_FEATURE_FILS_CRYPTO_OFFLOAD,
NL80211_EXT_FEATURE_RADAR_BACKGROUND,
NL80211_EXT_FEATURE_POWERED_ADDR_CHANGE,
NL80211_EXT_FEATURE_PUNCT,
NL80211_EXT_FEATURE_SECURE_NAN,
NL80211_EXT_FEATURE_AUTH_AND_DEAUTH_RANDOM_TA,
/* add new features before the definition below */
NUM_NL80211_EXT_FEATURES,
MAX_NL80211_EXT_FEATURES = NUM_NL80211_EXT_FEATURES - 1
};
/**
* enum nl80211_probe_resp_offload_support_attr - optional supported
* protocols for probe-response offloading by the driver/FW.
* To be used with the %NL80211_ATTR_PROBE_RESP_OFFLOAD attribute.
* Each enum value represents a bit in the bitmap of supported
* protocols. Typically a subset of probe-requests belonging to a
* supported protocol will be excluded from offload and uploaded
* to the host.
*
* @NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS: Support for WPS ver. 1
* @NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS2: Support for WPS ver. 2
* @NL80211_PROBE_RESP_OFFLOAD_SUPPORT_P2P: Support for P2P
* @NL80211_PROBE_RESP_OFFLOAD_SUPPORT_80211U: Support for 802.11u
*/
enum nl80211_probe_resp_offload_support_attr {
NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS = 1<<0,
NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS2 = 1<<1,
NL80211_PROBE_RESP_OFFLOAD_SUPPORT_P2P = 1<<2,
NL80211_PROBE_RESP_OFFLOAD_SUPPORT_80211U = 1<<3,
};
/**
* enum nl80211_connect_failed_reason - connection request failed reasons
* @NL80211_CONN_FAIL_MAX_CLIENTS: Maximum number of clients that can be
* handled by the AP is reached.
* @NL80211_CONN_FAIL_BLOCKED_CLIENT: Connection request is rejected due to ACL.
*/
enum nl80211_connect_failed_reason {
NL80211_CONN_FAIL_MAX_CLIENTS,
NL80211_CONN_FAIL_BLOCKED_CLIENT,
};
/**
* enum nl80211_timeout_reason - timeout reasons
*
* @NL80211_TIMEOUT_UNSPECIFIED: Timeout reason unspecified.
* @NL80211_TIMEOUT_SCAN: Scan (AP discovery) timed out.
* @NL80211_TIMEOUT_AUTH: Authentication timed out.
* @NL80211_TIMEOUT_ASSOC: Association timed out.
*/
enum nl80211_timeout_reason {
NL80211_TIMEOUT_UNSPECIFIED,
NL80211_TIMEOUT_SCAN,
NL80211_TIMEOUT_AUTH,
NL80211_TIMEOUT_ASSOC,
};
/**
* enum nl80211_scan_flags - scan request control flags
*
* Scan request control flags are used to control the handling
* of NL80211_CMD_TRIGGER_SCAN and NL80211_CMD_START_SCHED_SCAN
* requests.
*
* NL80211_SCAN_FLAG_LOW_SPAN, NL80211_SCAN_FLAG_LOW_POWER, and
* NL80211_SCAN_FLAG_HIGH_ACCURACY flags are exclusive of each other, i.e., only
* one of them can be used in the request.
*
* @NL80211_SCAN_FLAG_LOW_PRIORITY: scan request has low priority
* @NL80211_SCAN_FLAG_FLUSH: flush cache before scanning
* @NL80211_SCAN_FLAG_AP: force a scan even if the interface is configured
* as AP and the beaconing has already been configured. This attribute is
* dangerous because will destroy stations performance as a lot of frames
* will be lost while scanning off-channel, therefore it must be used only
* when really needed
* @NL80211_SCAN_FLAG_RANDOM_ADDR: use a random MAC address for this scan (or
* for scheduled scan: a different one for every scan iteration). When the
* flag is set, depending on device capabilities the @NL80211_ATTR_MAC and
* @NL80211_ATTR_MAC_MASK attributes may also be given in which case only
* the masked bits will be preserved from the MAC address and the remainder
* randomised. If the attributes are not given full randomisation (46 bits,
* locally administered 1, multicast 0) is assumed.
* This flag must not be requested when the feature isn't supported, check
* the nl80211 feature flags for the device.
* @NL80211_SCAN_FLAG_FILS_MAX_CHANNEL_TIME: fill the dwell time in the FILS
* request parameters IE in the probe request
* @NL80211_SCAN_FLAG_ACCEPT_BCAST_PROBE_RESP: accept broadcast probe responses
* @NL80211_SCAN_FLAG_OCE_PROBE_REQ_HIGH_TX_RATE: send probe request frames at
* rate of at least 5.5M. In case non OCE AP is discovered in the channel,
* only the first probe req in the channel will be sent in high rate.
* @NL80211_SCAN_FLAG_OCE_PROBE_REQ_DEFERRAL_SUPPRESSION: allow probe request
* tx deferral (dot11FILSProbeDelay shall be set to 15ms)
* and suppression (if it has received a broadcast Probe Response frame,
* Beacon frame or FILS Discovery frame from an AP that the STA considers
* a suitable candidate for (re-)association - suitable in terms of
* SSID and/or RSSI.
* @NL80211_SCAN_FLAG_LOW_SPAN: Span corresponds to the total time taken to
* accomplish the scan. Thus, this flag intends the driver to perform the
* scan request with lesser span/duration. It is specific to the driver
* implementations on how this is accomplished. Scan accuracy may get
* impacted with this flag.
* @NL80211_SCAN_FLAG_LOW_POWER: This flag intends the scan attempts to consume
* optimal possible power. Drivers can resort to their specific means to
* optimize the power. Scan accuracy may get impacted with this flag.
* @NL80211_SCAN_FLAG_HIGH_ACCURACY: Accuracy here intends to the extent of scan
* results obtained. Thus HIGH_ACCURACY scan flag aims to get maximum
* possible scan results. This flag hints the driver to use the best
* possible scan configuration to improve the accuracy in scanning.
* Latency and power use may get impacted with this flag.
* @NL80211_SCAN_FLAG_RANDOM_SN: randomize the sequence number in probe
* request frames from this scan to avoid correlation/tracking being
* possible.
* @NL80211_SCAN_FLAG_MIN_PREQ_CONTENT: minimize probe request content to
* only have supported rates and no additional capabilities (unless
* added by userspace explicitly.)
* @NL80211_SCAN_FLAG_FREQ_KHZ: report scan results with
* %NL80211_ATTR_SCAN_FREQ_KHZ. This also means
* %NL80211_ATTR_SCAN_FREQUENCIES will not be included.
* @NL80211_SCAN_FLAG_COLOCATED_6GHZ: scan for collocated APs reported by
* 2.4/5 GHz APs. When the flag is set, the scan logic will use the
* information from the RNR element found in beacons/probe responses
* received on the 2.4/5 GHz channels to actively scan only the 6GHz
* channels on which APs are expected to be found. Note that when not set,
* the scan logic would scan all 6GHz channels, but since transmission of
* probe requests on non PSC channels is limited, it is highly likely that
* these channels would passively be scanned. Also note that when the flag
* is set, in addition to the colocated APs, PSC channels would also be
* scanned if the user space has asked for it.
*/
enum nl80211_scan_flags {
NL80211_SCAN_FLAG_LOW_PRIORITY = 1<<0,
NL80211_SCAN_FLAG_FLUSH = 1<<1,
NL80211_SCAN_FLAG_AP = 1<<2,
NL80211_SCAN_FLAG_RANDOM_ADDR = 1<<3,
NL80211_SCAN_FLAG_FILS_MAX_CHANNEL_TIME = 1<<4,
NL80211_SCAN_FLAG_ACCEPT_BCAST_PROBE_RESP = 1<<5,
NL80211_SCAN_FLAG_OCE_PROBE_REQ_HIGH_TX_RATE = 1<<6,
NL80211_SCAN_FLAG_OCE_PROBE_REQ_DEFERRAL_SUPPRESSION = 1<<7,
NL80211_SCAN_FLAG_LOW_SPAN = 1<<8,
NL80211_SCAN_FLAG_LOW_POWER = 1<<9,
NL80211_SCAN_FLAG_HIGH_ACCURACY = 1<<10,
NL80211_SCAN_FLAG_RANDOM_SN = 1<<11,
NL80211_SCAN_FLAG_MIN_PREQ_CONTENT = 1<<12,
NL80211_SCAN_FLAG_FREQ_KHZ = 1<<13,
NL80211_SCAN_FLAG_COLOCATED_6GHZ = 1<<14,
};
/**
* enum nl80211_acl_policy - access control policy
*
* Access control policy is applied on a MAC list set by
* %NL80211_CMD_START_AP and %NL80211_CMD_SET_MAC_ACL, to
* be used with %NL80211_ATTR_ACL_POLICY.
*
* @NL80211_ACL_POLICY_ACCEPT_UNLESS_LISTED: Deny stations which are
* listed in ACL, i.e. allow all the stations which are not listed
* in ACL to authenticate.
* @NL80211_ACL_POLICY_DENY_UNLESS_LISTED: Allow the stations which are listed
* in ACL, i.e. deny all the stations which are not listed in ACL.
*/
enum nl80211_acl_policy {
NL80211_ACL_POLICY_ACCEPT_UNLESS_LISTED,
NL80211_ACL_POLICY_DENY_UNLESS_LISTED,
};
/**
* enum nl80211_smps_mode - SMPS mode
*
* Requested SMPS mode (for AP mode)
*
* @NL80211_SMPS_OFF: SMPS off (use all antennas).
* @NL80211_SMPS_STATIC: static SMPS (use a single antenna)
* @NL80211_SMPS_DYNAMIC: dynamic smps (start with a single antenna and
* turn on other antennas after CTS/RTS).
*/
enum nl80211_smps_mode {
NL80211_SMPS_OFF,
NL80211_SMPS_STATIC,
NL80211_SMPS_DYNAMIC,
__NL80211_SMPS_AFTER_LAST,
NL80211_SMPS_MAX = __NL80211_SMPS_AFTER_LAST - 1
};
/**
* enum nl80211_radar_event - type of radar event for DFS operation
*
* Type of event to be used with NL80211_ATTR_RADAR_EVENT to inform userspace
* about detected radars or success of the channel available check (CAC)
*
* @NL80211_RADAR_DETECTED: A radar pattern has been detected. The channel is
* now unusable.
* @NL80211_RADAR_CAC_FINISHED: Channel Availability Check has been finished,
* the channel is now available.
* @NL80211_RADAR_CAC_ABORTED: Channel Availability Check has been aborted, no
* change to the channel status.
* @NL80211_RADAR_NOP_FINISHED: The Non-Occupancy Period for this channel is
* over, channel becomes usable.
* @NL80211_RADAR_PRE_CAC_EXPIRED: Channel Availability Check done on this
* non-operating channel is expired and no longer valid. New CAC must
* be done on this channel before starting the operation. This is not
* applicable for ETSI dfs domain where pre-CAC is valid for ever.
* @NL80211_RADAR_CAC_STARTED: Channel Availability Check has been started,
* should be generated by HW if NL80211_EXT_FEATURE_DFS_OFFLOAD is enabled.
*/
enum nl80211_radar_event {
NL80211_RADAR_DETECTED,
NL80211_RADAR_CAC_FINISHED,
NL80211_RADAR_CAC_ABORTED,
NL80211_RADAR_NOP_FINISHED,
NL80211_RADAR_PRE_CAC_EXPIRED,
NL80211_RADAR_CAC_STARTED,
};
/**
* enum nl80211_dfs_state - DFS states for channels
*
* Channel states used by the DFS code.
*
* @NL80211_DFS_USABLE: The channel can be used, but channel availability
* check (CAC) must be performed before using it for AP or IBSS.
* @NL80211_DFS_UNAVAILABLE: A radar has been detected on this channel, it
* is therefore marked as not available.
* @NL80211_DFS_AVAILABLE: The channel has been CAC checked and is available.
*/
enum nl80211_dfs_state {
NL80211_DFS_USABLE,
NL80211_DFS_UNAVAILABLE,
NL80211_DFS_AVAILABLE,
};
/**
* enum nl80211_protocol_features - nl80211 protocol features
* @NL80211_PROTOCOL_FEATURE_SPLIT_WIPHY_DUMP: nl80211 supports splitting
* wiphy dumps (if requested by the application with the attribute
* %NL80211_ATTR_SPLIT_WIPHY_DUMP. Also supported is filtering the
* wiphy dump by %NL80211_ATTR_WIPHY, %NL80211_ATTR_IFINDEX or
* %NL80211_ATTR_WDEV.
*/
enum nl80211_protocol_features {
NL80211_PROTOCOL_FEATURE_SPLIT_WIPHY_DUMP = 1 << 0,
};
/**
* enum nl80211_crit_proto_id - nl80211 critical protocol identifiers
*
* @NL80211_CRIT_PROTO_UNSPEC: protocol unspecified.
* @NL80211_CRIT_PROTO_DHCP: BOOTP or DHCPv6 protocol.
* @NL80211_CRIT_PROTO_EAPOL: EAPOL protocol.
* @NL80211_CRIT_PROTO_APIPA: APIPA protocol.
* @NUM_NL80211_CRIT_PROTO: must be kept last.
*/
enum nl80211_crit_proto_id {
NL80211_CRIT_PROTO_UNSPEC,
NL80211_CRIT_PROTO_DHCP,
NL80211_CRIT_PROTO_EAPOL,
NL80211_CRIT_PROTO_APIPA,
/* add other protocols before this one */
NUM_NL80211_CRIT_PROTO
};
/* maximum duration for critical protocol measures */
#define NL80211_CRIT_PROTO_MAX_DURATION 5000 /* msec */
/**
* enum nl80211_rxmgmt_flags - flags for received management frame.
*
* Used by cfg80211_rx_mgmt()
*
* @NL80211_RXMGMT_FLAG_ANSWERED: frame was answered by device/driver.
* @NL80211_RXMGMT_FLAG_EXTERNAL_AUTH: Host driver intends to offload
* the authentication. Exclusively defined for host drivers that
* advertises the SME functionality but would like the userspace
* to handle certain authentication algorithms (e.g. SAE).
*/
enum nl80211_rxmgmt_flags {
NL80211_RXMGMT_FLAG_ANSWERED = 1 << 0,
NL80211_RXMGMT_FLAG_EXTERNAL_AUTH = 1 << 1,
};
/*
* If this flag is unset, the lower 24 bits are an OUI, if set
* a Linux nl80211 vendor ID is used (no such IDs are allocated
* yet, so that's not valid so far)
*/
#define NL80211_VENDOR_ID_IS_LINUX 0x80000000
/**
* struct nl80211_vendor_cmd_info - vendor command data
* @vendor_id: If the %NL80211_VENDOR_ID_IS_LINUX flag is clear, then the
* value is a 24-bit OUI; if it is set then a separately allocated ID
* may be used, but no such IDs are allocated yet. New IDs should be
* added to this file when needed.
* @subcmd: sub-command ID for the command
*/
struct nl80211_vendor_cmd_info {
__u32 vendor_id;
__u32 subcmd;
};
/**
* enum nl80211_tdls_peer_capability - TDLS peer flags.
*
* Used by tdls_mgmt() to determine which conditional elements need
* to be added to TDLS Setup frames.
*
* @NL80211_TDLS_PEER_HT: TDLS peer is HT capable.
* @NL80211_TDLS_PEER_VHT: TDLS peer is VHT capable.
* @NL80211_TDLS_PEER_WMM: TDLS peer is WMM capable.
* @NL80211_TDLS_PEER_HE: TDLS peer is HE capable.
*/
enum nl80211_tdls_peer_capability {
NL80211_TDLS_PEER_HT = 1<<0,
NL80211_TDLS_PEER_VHT = 1<<1,
NL80211_TDLS_PEER_WMM = 1<<2,
NL80211_TDLS_PEER_HE = 1<<3,
};
/**
* enum nl80211_sched_scan_plan - scanning plan for scheduled scan
* @__NL80211_SCHED_SCAN_PLAN_INVALID: attribute number 0 is reserved
* @NL80211_SCHED_SCAN_PLAN_INTERVAL: interval between scan iterations. In
* seconds (u32).
* @NL80211_SCHED_SCAN_PLAN_ITERATIONS: number of scan iterations in this
* scan plan (u32). The last scan plan must not specify this attribute
* because it will run infinitely. A value of zero is invalid as it will
* make the scan plan meaningless.
* @NL80211_SCHED_SCAN_PLAN_MAX: highest scheduled scan plan attribute number
* currently defined
* @__NL80211_SCHED_SCAN_PLAN_AFTER_LAST: internal use
*/
enum nl80211_sched_scan_plan {
__NL80211_SCHED_SCAN_PLAN_INVALID,
NL80211_SCHED_SCAN_PLAN_INTERVAL,
NL80211_SCHED_SCAN_PLAN_ITERATIONS,
/* keep last */
__NL80211_SCHED_SCAN_PLAN_AFTER_LAST,
NL80211_SCHED_SCAN_PLAN_MAX =
__NL80211_SCHED_SCAN_PLAN_AFTER_LAST - 1
};
/**
* struct nl80211_bss_select_rssi_adjust - RSSI adjustment parameters.
*
* @band: band of BSS that must match for RSSI value adjustment. The value
* of this field is according to &enum nl80211_band.
* @delta: value used to adjust the RSSI value of matching BSS in dB.
*/
struct nl80211_bss_select_rssi_adjust {
__u8 band;
__s8 delta;
} __attribute__((packed));
/**
* enum nl80211_bss_select_attr - attributes for bss selection.
*
* @__NL80211_BSS_SELECT_ATTR_INVALID: reserved.
* @NL80211_BSS_SELECT_ATTR_RSSI: Flag indicating only RSSI-based BSS selection
* is requested.
* @NL80211_BSS_SELECT_ATTR_BAND_PREF: attribute indicating BSS
* selection should be done such that the specified band is preferred.
* When there are multiple BSS-es in the preferred band, the driver
* shall use RSSI-based BSS selection as a second step. The value of
* this attribute is according to &enum nl80211_band (u32).
* @NL80211_BSS_SELECT_ATTR_RSSI_ADJUST: When present the RSSI level for
* BSS-es in the specified band is to be adjusted before doing
* RSSI-based BSS selection. The attribute value is a packed structure
* value as specified by &struct nl80211_bss_select_rssi_adjust.
* @NL80211_BSS_SELECT_ATTR_MAX: highest bss select attribute number.
* @__NL80211_BSS_SELECT_ATTR_AFTER_LAST: internal use.
*
* One and only one of these attributes are found within %NL80211_ATTR_BSS_SELECT
* for %NL80211_CMD_CONNECT. It specifies the required BSS selection behaviour
* which the driver shall use.
*/
enum nl80211_bss_select_attr {
__NL80211_BSS_SELECT_ATTR_INVALID,
NL80211_BSS_SELECT_ATTR_RSSI,
NL80211_BSS_SELECT_ATTR_BAND_PREF,
NL80211_BSS_SELECT_ATTR_RSSI_ADJUST,
/* keep last */
__NL80211_BSS_SELECT_ATTR_AFTER_LAST,
NL80211_BSS_SELECT_ATTR_MAX = __NL80211_BSS_SELECT_ATTR_AFTER_LAST - 1
};
/**
* enum nl80211_nan_function_type - NAN function type
*
* Defines the function type of a NAN function
*
* @NL80211_NAN_FUNC_PUBLISH: function is publish
* @NL80211_NAN_FUNC_SUBSCRIBE: function is subscribe
* @NL80211_NAN_FUNC_FOLLOW_UP: function is follow-up
*/
enum nl80211_nan_function_type {
NL80211_NAN_FUNC_PUBLISH,
NL80211_NAN_FUNC_SUBSCRIBE,
NL80211_NAN_FUNC_FOLLOW_UP,
/* keep last */
__NL80211_NAN_FUNC_TYPE_AFTER_LAST,
NL80211_NAN_FUNC_MAX_TYPE = __NL80211_NAN_FUNC_TYPE_AFTER_LAST - 1,
};
/**
* enum nl80211_nan_publish_type - NAN publish tx type
*
* Defines how to send publish Service Discovery Frames
*
* @NL80211_NAN_SOLICITED_PUBLISH: publish function is solicited
* @NL80211_NAN_UNSOLICITED_PUBLISH: publish function is unsolicited
*/
enum nl80211_nan_publish_type {
NL80211_NAN_SOLICITED_PUBLISH = 1 << 0,
NL80211_NAN_UNSOLICITED_PUBLISH = 1 << 1,
};
/**
* enum nl80211_nan_func_term_reason - NAN functions termination reason
*
* Defines termination reasons of a NAN function
*
* @NL80211_NAN_FUNC_TERM_REASON_USER_REQUEST: requested by user
* @NL80211_NAN_FUNC_TERM_REASON_TTL_EXPIRED: timeout
* @NL80211_NAN_FUNC_TERM_REASON_ERROR: errored
*/
enum nl80211_nan_func_term_reason {
NL80211_NAN_FUNC_TERM_REASON_USER_REQUEST,
NL80211_NAN_FUNC_TERM_REASON_TTL_EXPIRED,
NL80211_NAN_FUNC_TERM_REASON_ERROR,
};
#define NL80211_NAN_FUNC_SERVICE_ID_LEN 6
#define NL80211_NAN_FUNC_SERVICE_SPEC_INFO_MAX_LEN 0xff
#define NL80211_NAN_FUNC_SRF_MAX_LEN 0xff
/**
* enum nl80211_nan_func_attributes - NAN function attributes
* @__NL80211_NAN_FUNC_INVALID: invalid
* @NL80211_NAN_FUNC_TYPE: &enum nl80211_nan_function_type (u8).
* @NL80211_NAN_FUNC_SERVICE_ID: 6 bytes of the service ID hash as
* specified in NAN spec. This is a binary attribute.
* @NL80211_NAN_FUNC_PUBLISH_TYPE: relevant if the function's type is
* publish. Defines the transmission type for the publish Service Discovery
* Frame, see &enum nl80211_nan_publish_type. Its type is u8.
* @NL80211_NAN_FUNC_PUBLISH_BCAST: relevant if the function is a solicited
* publish. Should the solicited publish Service Discovery Frame be sent to
* the NAN Broadcast address. This is a flag.
* @NL80211_NAN_FUNC_SUBSCRIBE_ACTIVE: relevant if the function's type is
* subscribe. Is the subscribe active. This is a flag.
* @NL80211_NAN_FUNC_FOLLOW_UP_ID: relevant if the function's type is follow up.
* The instance ID for the follow up Service Discovery Frame. This is u8.
* @NL80211_NAN_FUNC_FOLLOW_UP_REQ_ID: relevant if the function's type
* is follow up. This is a u8.
* The requestor instance ID for the follow up Service Discovery Frame.
* @NL80211_NAN_FUNC_FOLLOW_UP_DEST: the MAC address of the recipient of the
* follow up Service Discovery Frame. This is a binary attribute.
* @NL80211_NAN_FUNC_CLOSE_RANGE: is this function limited for devices in a
* close range. The range itself (RSSI) is defined by the device.
* This is a flag.
* @NL80211_NAN_FUNC_TTL: strictly positive number of DWs this function should
* stay active. If not present infinite TTL is assumed. This is a u32.
* @NL80211_NAN_FUNC_SERVICE_INFO: array of bytes describing the service
* specific info. This is a binary attribute.
* @NL80211_NAN_FUNC_SRF: Service Receive Filter. This is a nested attribute.
* See &enum nl80211_nan_srf_attributes.
* @NL80211_NAN_FUNC_RX_MATCH_FILTER: Receive Matching filter. This is a nested
* attribute. It is a list of binary values.
* @NL80211_NAN_FUNC_TX_MATCH_FILTER: Transmit Matching filter. This is a
* nested attribute. It is a list of binary values.
* @NL80211_NAN_FUNC_INSTANCE_ID: The instance ID of the function.
* Its type is u8 and it cannot be 0.
* @NL80211_NAN_FUNC_TERM_REASON: NAN function termination reason.
* See &enum nl80211_nan_func_term_reason.
*
* @NUM_NL80211_NAN_FUNC_ATTR: internal
* @NL80211_NAN_FUNC_ATTR_MAX: highest NAN function attribute
*/
enum nl80211_nan_func_attributes {
__NL80211_NAN_FUNC_INVALID,
NL80211_NAN_FUNC_TYPE,
NL80211_NAN_FUNC_SERVICE_ID,
NL80211_NAN_FUNC_PUBLISH_TYPE,
NL80211_NAN_FUNC_PUBLISH_BCAST,
NL80211_NAN_FUNC_SUBSCRIBE_ACTIVE,
NL80211_NAN_FUNC_FOLLOW_UP_ID,
NL80211_NAN_FUNC_FOLLOW_UP_REQ_ID,
NL80211_NAN_FUNC_FOLLOW_UP_DEST,
NL80211_NAN_FUNC_CLOSE_RANGE,
NL80211_NAN_FUNC_TTL,
NL80211_NAN_FUNC_SERVICE_INFO,
NL80211_NAN_FUNC_SRF,
NL80211_NAN_FUNC_RX_MATCH_FILTER,
NL80211_NAN_FUNC_TX_MATCH_FILTER,
NL80211_NAN_FUNC_INSTANCE_ID,
NL80211_NAN_FUNC_TERM_REASON,
/* keep last */
NUM_NL80211_NAN_FUNC_ATTR,
NL80211_NAN_FUNC_ATTR_MAX = NUM_NL80211_NAN_FUNC_ATTR - 1
};
/**
* enum nl80211_nan_srf_attributes - NAN Service Response filter attributes
* @__NL80211_NAN_SRF_INVALID: invalid
* @NL80211_NAN_SRF_INCLUDE: present if the include bit of the SRF set.
* This is a flag.
* @NL80211_NAN_SRF_BF: Bloom Filter. Present if and only if
* %NL80211_NAN_SRF_MAC_ADDRS isn't present. This attribute is binary.
* @NL80211_NAN_SRF_BF_IDX: index of the Bloom Filter. Mandatory if
* %NL80211_NAN_SRF_BF is present. This is a u8.
* @NL80211_NAN_SRF_MAC_ADDRS: list of MAC addresses for the SRF. Present if
* and only if %NL80211_NAN_SRF_BF isn't present. This is a nested
* attribute. Each nested attribute is a MAC address.
* @NUM_NL80211_NAN_SRF_ATTR: internal
* @NL80211_NAN_SRF_ATTR_MAX: highest NAN SRF attribute
*/
enum nl80211_nan_srf_attributes {
__NL80211_NAN_SRF_INVALID,
NL80211_NAN_SRF_INCLUDE,
NL80211_NAN_SRF_BF,
NL80211_NAN_SRF_BF_IDX,
NL80211_NAN_SRF_MAC_ADDRS,
/* keep last */
NUM_NL80211_NAN_SRF_ATTR,
NL80211_NAN_SRF_ATTR_MAX = NUM_NL80211_NAN_SRF_ATTR - 1,
};
/**
* enum nl80211_nan_match_attributes - NAN match attributes
* @__NL80211_NAN_MATCH_INVALID: invalid
* @NL80211_NAN_MATCH_FUNC_LOCAL: the local function that had the
* match. This is a nested attribute.
* See &enum nl80211_nan_func_attributes.
* @NL80211_NAN_MATCH_FUNC_PEER: the peer function
* that caused the match. This is a nested attribute.
* See &enum nl80211_nan_func_attributes.
*
* @NUM_NL80211_NAN_MATCH_ATTR: internal
* @NL80211_NAN_MATCH_ATTR_MAX: highest NAN match attribute
*/
enum nl80211_nan_match_attributes {
__NL80211_NAN_MATCH_INVALID,
NL80211_NAN_MATCH_FUNC_LOCAL,
NL80211_NAN_MATCH_FUNC_PEER,
/* keep last */
NUM_NL80211_NAN_MATCH_ATTR,
NL80211_NAN_MATCH_ATTR_MAX = NUM_NL80211_NAN_MATCH_ATTR - 1
};
/**
* nl80211_external_auth_action - Action to perform with external
* authentication request. Used by NL80211_ATTR_EXTERNAL_AUTH_ACTION.
* @NL80211_EXTERNAL_AUTH_START: Start the authentication.
* @NL80211_EXTERNAL_AUTH_ABORT: Abort the ongoing authentication.
*/
enum nl80211_external_auth_action {
NL80211_EXTERNAL_AUTH_START,
NL80211_EXTERNAL_AUTH_ABORT,
};
/**
* enum nl80211_ftm_responder_attributes - fine timing measurement
* responder attributes
* @__NL80211_FTM_RESP_ATTR_INVALID: Invalid
* @NL80211_FTM_RESP_ATTR_ENABLED: FTM responder is enabled
* @NL80211_FTM_RESP_ATTR_LCI: The content of Measurement Report Element
* (9.4.2.22 in 802.11-2016) with type 8 - LCI (9.4.2.22.10),
* i.e. starting with the measurement token
* @NL80211_FTM_RESP_ATTR_CIVIC: The content of Measurement Report Element
* (9.4.2.22 in 802.11-2016) with type 11 - Civic (Section 9.4.2.22.13),
* i.e. starting with the measurement token
* @__NL80211_FTM_RESP_ATTR_LAST: Internal
* @NL80211_FTM_RESP_ATTR_MAX: highest FTM responder attribute.
*/
enum nl80211_ftm_responder_attributes {
__NL80211_FTM_RESP_ATTR_INVALID,
NL80211_FTM_RESP_ATTR_ENABLED,
NL80211_FTM_RESP_ATTR_LCI,
NL80211_FTM_RESP_ATTR_CIVICLOC,
/* keep last */
__NL80211_FTM_RESP_ATTR_LAST,
NL80211_FTM_RESP_ATTR_MAX = __NL80211_FTM_RESP_ATTR_LAST - 1,
};
/*
* enum nl80211_ftm_responder_stats - FTM responder statistics
*
* These attribute types are used with %NL80211_ATTR_FTM_RESPONDER_STATS
* when getting FTM responder statistics.
*
* @__NL80211_FTM_STATS_INVALID: attribute number 0 is reserved
* @NL80211_FTM_STATS_SUCCESS_NUM: number of FTM sessions in which all frames
* were ssfully answered (u32)
* @NL80211_FTM_STATS_PARTIAL_NUM: number of FTM sessions in which part of the
* frames were successfully answered (u32)
* @NL80211_FTM_STATS_FAILED_NUM: number of failed FTM sessions (u32)
* @NL80211_FTM_STATS_ASAP_NUM: number of ASAP sessions (u32)
* @NL80211_FTM_STATS_NON_ASAP_NUM: number of non-ASAP sessions (u32)
* @NL80211_FTM_STATS_TOTAL_DURATION_MSEC: total sessions durations - gives an
* indication of how much time the responder was busy (u64, msec)
* @NL80211_FTM_STATS_UNKNOWN_TRIGGERS_NUM: number of unknown FTM triggers -
* triggers from initiators that didn't finish successfully the negotiation
* phase with the responder (u32)
* @NL80211_FTM_STATS_RESCHEDULE_REQUESTS_NUM: number of FTM reschedule requests
* - initiator asks for a new scheduling although it already has scheduled
* FTM slot (u32)
* @NL80211_FTM_STATS_OUT_OF_WINDOW_TRIGGERS_NUM: number of FTM triggers out of
* scheduled window (u32)
* @NL80211_FTM_STATS_PAD: used for padding, ignore
* @__NL80211_TXQ_ATTR_AFTER_LAST: Internal
* @NL80211_FTM_STATS_MAX: highest possible FTM responder stats attribute
*/
enum nl80211_ftm_responder_stats {
__NL80211_FTM_STATS_INVALID,
NL80211_FTM_STATS_SUCCESS_NUM,
NL80211_FTM_STATS_PARTIAL_NUM,
NL80211_FTM_STATS_FAILED_NUM,
NL80211_FTM_STATS_ASAP_NUM,
NL80211_FTM_STATS_NON_ASAP_NUM,
NL80211_FTM_STATS_TOTAL_DURATION_MSEC,
NL80211_FTM_STATS_UNKNOWN_TRIGGERS_NUM,
NL80211_FTM_STATS_RESCHEDULE_REQUESTS_NUM,
NL80211_FTM_STATS_OUT_OF_WINDOW_TRIGGERS_NUM,
NL80211_FTM_STATS_PAD,
/* keep last */
__NL80211_FTM_STATS_AFTER_LAST,
NL80211_FTM_STATS_MAX = __NL80211_FTM_STATS_AFTER_LAST - 1
};
/**
* enum nl80211_preamble - frame preamble types
* @NL80211_PREAMBLE_LEGACY: legacy (HR/DSSS, OFDM, ERP PHY) preamble
* @NL80211_PREAMBLE_HT: HT preamble
* @NL80211_PREAMBLE_VHT: VHT preamble
* @NL80211_PREAMBLE_DMG: DMG preamble
* @NL80211_PREAMBLE_HE: HE preamble
*/
enum nl80211_preamble {
NL80211_PREAMBLE_LEGACY,
NL80211_PREAMBLE_HT,
NL80211_PREAMBLE_VHT,
NL80211_PREAMBLE_DMG,
NL80211_PREAMBLE_HE,
};
/**
* enum nl80211_peer_measurement_type - peer measurement types
* @NL80211_PMSR_TYPE_INVALID: invalid/unused, needed as we use
* these numbers also for attributes
*
* @NL80211_PMSR_TYPE_FTM: flight time measurement
*
* @NUM_NL80211_PMSR_TYPES: internal
* @NL80211_PMSR_TYPE_MAX: highest type number
*/
enum nl80211_peer_measurement_type {
NL80211_PMSR_TYPE_INVALID,
NL80211_PMSR_TYPE_FTM,
NUM_NL80211_PMSR_TYPES,
NL80211_PMSR_TYPE_MAX = NUM_NL80211_PMSR_TYPES - 1
};
/**
* enum nl80211_peer_measurement_status - peer measurement status
* @NL80211_PMSR_STATUS_SUCCESS: measurement completed successfully
* @NL80211_PMSR_STATUS_REFUSED: measurement was locally refused
* @NL80211_PMSR_STATUS_TIMEOUT: measurement timed out
* @NL80211_PMSR_STATUS_FAILURE: measurement failed, a type-dependent
* reason may be available in the response data
*/
enum nl80211_peer_measurement_status {
NL80211_PMSR_STATUS_SUCCESS,
NL80211_PMSR_STATUS_REFUSED,
NL80211_PMSR_STATUS_TIMEOUT,
NL80211_PMSR_STATUS_FAILURE,
};
/**
* enum nl80211_peer_measurement_req - peer measurement request attributes
* @__NL80211_PMSR_REQ_ATTR_INVALID: invalid
*
* @NL80211_PMSR_REQ_ATTR_DATA: This is a nested attribute with measurement
* type-specific request data inside. The attributes used are from the
* enums named nl80211_peer_measurement_<type>_req.
* @NL80211_PMSR_REQ_ATTR_GET_AP_TSF: include AP TSF timestamp, if supported
* (flag attribute)
*
* @NUM_NL80211_PMSR_REQ_ATTRS: internal
* @NL80211_PMSR_REQ_ATTR_MAX: highest attribute number
*/
enum nl80211_peer_measurement_req {
__NL80211_PMSR_REQ_ATTR_INVALID,
NL80211_PMSR_REQ_ATTR_DATA,
NL80211_PMSR_REQ_ATTR_GET_AP_TSF,
/* keep last */
NUM_NL80211_PMSR_REQ_ATTRS,
NL80211_PMSR_REQ_ATTR_MAX = NUM_NL80211_PMSR_REQ_ATTRS - 1
};
/**
* enum nl80211_peer_measurement_resp - peer measurement response attributes
* @__NL80211_PMSR_RESP_ATTR_INVALID: invalid
*
* @NL80211_PMSR_RESP_ATTR_DATA: This is a nested attribute with measurement
* type-specific results inside. The attributes used are from the enums
* named nl80211_peer_measurement_<type>_resp.
* @NL80211_PMSR_RESP_ATTR_STATUS: u32 value with the measurement status
* (using values from &enum nl80211_peer_measurement_status.)
* @NL80211_PMSR_RESP_ATTR_HOST_TIME: host time (%CLOCK_BOOTTIME) when the
* result was measured; this value is not expected to be accurate to
* more than 20ms. (u64, nanoseconds)
* @NL80211_PMSR_RESP_ATTR_AP_TSF: TSF of the AP that the interface
* doing the measurement is connected to when the result was measured.
* This shall be accurately reported if supported and requested
* (u64, usec)
* @NL80211_PMSR_RESP_ATTR_FINAL: If results are sent to the host partially
* (*e.g. with FTM per-burst data) this flag will be cleared on all but
* the last result; if all results are combined it's set on the single
* result.
* @NL80211_PMSR_RESP_ATTR_PAD: padding for 64-bit attributes, ignore
*
* @NUM_NL80211_PMSR_RESP_ATTRS: internal
* @NL80211_PMSR_RESP_ATTR_MAX: highest attribute number
*/
enum nl80211_peer_measurement_resp {
__NL80211_PMSR_RESP_ATTR_INVALID,
NL80211_PMSR_RESP_ATTR_DATA,
NL80211_PMSR_RESP_ATTR_STATUS,
NL80211_PMSR_RESP_ATTR_HOST_TIME,
NL80211_PMSR_RESP_ATTR_AP_TSF,
NL80211_PMSR_RESP_ATTR_FINAL,
NL80211_PMSR_RESP_ATTR_PAD,
/* keep last */
NUM_NL80211_PMSR_RESP_ATTRS,
NL80211_PMSR_RESP_ATTR_MAX = NUM_NL80211_PMSR_RESP_ATTRS - 1
};
/**
* enum nl80211_peer_measurement_peer_attrs - peer attributes for measurement
* @__NL80211_PMSR_PEER_ATTR_INVALID: invalid
*
* @NL80211_PMSR_PEER_ATTR_ADDR: peer's MAC address
* @NL80211_PMSR_PEER_ATTR_CHAN: channel definition, nested, using top-level
* attributes like %NL80211_ATTR_WIPHY_FREQ etc.
* @NL80211_PMSR_PEER_ATTR_REQ: This is a nested attribute indexed by
* measurement type, with attributes from the
* &enum nl80211_peer_measurement_req inside.
* @NL80211_PMSR_PEER_ATTR_RESP: This is a nested attribute indexed by
* measurement type, with attributes from the
* &enum nl80211_peer_measurement_resp inside.
*
* @NUM_NL80211_PMSR_PEER_ATTRS: internal
* @NL80211_PMSR_PEER_ATTR_MAX: highest attribute number
*/
enum nl80211_peer_measurement_peer_attrs {
__NL80211_PMSR_PEER_ATTR_INVALID,
NL80211_PMSR_PEER_ATTR_ADDR,
NL80211_PMSR_PEER_ATTR_CHAN,
NL80211_PMSR_PEER_ATTR_REQ,
NL80211_PMSR_PEER_ATTR_RESP,
/* keep last */
NUM_NL80211_PMSR_PEER_ATTRS,
NL80211_PMSR_PEER_ATTR_MAX = NUM_NL80211_PMSR_PEER_ATTRS - 1,
};
/**
* enum nl80211_peer_measurement_attrs - peer measurement attributes
* @__NL80211_PMSR_ATTR_INVALID: invalid
*
* @NL80211_PMSR_ATTR_MAX_PEERS: u32 attribute used for capability
* advertisement only, indicates the maximum number of peers
* measurements can be done with in a single request
* @NL80211_PMSR_ATTR_REPORT_AP_TSF: flag attribute in capability
* indicating that the connected AP's TSF can be reported in
* measurement results
* @NL80211_PMSR_ATTR_RANDOMIZE_MAC_ADDR: flag attribute in capability
* indicating that MAC address randomization is supported.
* @NL80211_PMSR_ATTR_TYPE_CAPA: capabilities reported by the device,
* this contains a nesting indexed by measurement type, and
* type-specific capabilities inside, which are from the enums
* named nl80211_peer_measurement_<type>_capa.
* @NL80211_PMSR_ATTR_PEERS: nested attribute, the nesting index is
* meaningless, just a list of peers to measure with, with the
* sub-attributes taken from
* &enum nl80211_peer_measurement_peer_attrs.
*
* @NUM_NL80211_PMSR_ATTR: internal
* @NL80211_PMSR_ATTR_MAX: highest attribute number
*/
enum nl80211_peer_measurement_attrs {
__NL80211_PMSR_ATTR_INVALID,
NL80211_PMSR_ATTR_MAX_PEERS,
NL80211_PMSR_ATTR_REPORT_AP_TSF,
NL80211_PMSR_ATTR_RANDOMIZE_MAC_ADDR,
NL80211_PMSR_ATTR_TYPE_CAPA,
NL80211_PMSR_ATTR_PEERS,
/* keep last */
NUM_NL80211_PMSR_ATTR,
NL80211_PMSR_ATTR_MAX = NUM_NL80211_PMSR_ATTR - 1
};
/**
* enum nl80211_peer_measurement_ftm_capa - FTM capabilities
* @__NL80211_PMSR_FTM_CAPA_ATTR_INVALID: invalid
*
* @NL80211_PMSR_FTM_CAPA_ATTR_ASAP: flag attribute indicating ASAP mode
* is supported
* @NL80211_PMSR_FTM_CAPA_ATTR_NON_ASAP: flag attribute indicating non-ASAP
* mode is supported
* @NL80211_PMSR_FTM_CAPA_ATTR_REQ_LCI: flag attribute indicating if LCI
* data can be requested during the measurement
* @NL80211_PMSR_FTM_CAPA_ATTR_REQ_CIVICLOC: flag attribute indicating if civic
* location data can be requested during the measurement
* @NL80211_PMSR_FTM_CAPA_ATTR_PREAMBLES: u32 bitmap attribute of bits
* from &enum nl80211_preamble.
* @NL80211_PMSR_FTM_CAPA_ATTR_BANDWIDTHS: bitmap of values from
* &enum nl80211_chan_width indicating the supported channel
* bandwidths for FTM. Note that a higher channel bandwidth may be
* configured to allow for other measurements types with different
* bandwidth requirement in the same measurement.
* @NL80211_PMSR_FTM_CAPA_ATTR_MAX_BURSTS_EXPONENT: u32 attribute indicating
* the maximum bursts exponent that can be used (if not present anything
* is valid)
* @NL80211_PMSR_FTM_CAPA_ATTR_MAX_FTMS_PER_BURST: u32 attribute indicating
* the maximum FTMs per burst (if not present anything is valid)
* @NL80211_PMSR_FTM_CAPA_ATTR_TRIGGER_BASED: flag attribute indicating if
* trigger based ranging measurement is supported
* @NL80211_PMSR_FTM_CAPA_ATTR_NON_TRIGGER_BASED: flag attribute indicating
* if non trigger based ranging measurement is supported
*
* @NUM_NL80211_PMSR_FTM_CAPA_ATTR: internal
* @NL80211_PMSR_FTM_CAPA_ATTR_MAX: highest attribute number
*/
enum nl80211_peer_measurement_ftm_capa {
__NL80211_PMSR_FTM_CAPA_ATTR_INVALID,
NL80211_PMSR_FTM_CAPA_ATTR_ASAP,
NL80211_PMSR_FTM_CAPA_ATTR_NON_ASAP,
NL80211_PMSR_FTM_CAPA_ATTR_REQ_LCI,
NL80211_PMSR_FTM_CAPA_ATTR_REQ_CIVICLOC,
NL80211_PMSR_FTM_CAPA_ATTR_PREAMBLES,
NL80211_PMSR_FTM_CAPA_ATTR_BANDWIDTHS,
NL80211_PMSR_FTM_CAPA_ATTR_MAX_BURSTS_EXPONENT,
NL80211_PMSR_FTM_CAPA_ATTR_MAX_FTMS_PER_BURST,
NL80211_PMSR_FTM_CAPA_ATTR_TRIGGER_BASED,
NL80211_PMSR_FTM_CAPA_ATTR_NON_TRIGGER_BASED,
/* keep last */
NUM_NL80211_PMSR_FTM_CAPA_ATTR,
NL80211_PMSR_FTM_CAPA_ATTR_MAX = NUM_NL80211_PMSR_FTM_CAPA_ATTR - 1
};
/**
* enum nl80211_peer_measurement_ftm_req - FTM request attributes
* @__NL80211_PMSR_FTM_REQ_ATTR_INVALID: invalid
*
* @NL80211_PMSR_FTM_REQ_ATTR_ASAP: ASAP mode requested (flag)
* @NL80211_PMSR_FTM_REQ_ATTR_PREAMBLE: preamble type (see
* &enum nl80211_preamble), optional for DMG (u32)
* @NL80211_PMSR_FTM_REQ_ATTR_NUM_BURSTS_EXP: number of bursts exponent as in
* 802.11-2016 9.4.2.168 "Fine Timing Measurement Parameters element"
* (u8, 0-15, optional with default 15 i.e. "no preference")
* @NL80211_PMSR_FTM_REQ_ATTR_BURST_PERIOD: interval between bursts in units
* of 100ms (u16, optional with default 0)
* @NL80211_PMSR_FTM_REQ_ATTR_BURST_DURATION: burst duration, as in 802.11-2016
* Table 9-257 "Burst Duration field encoding" (u8, 0-15, optional with
* default 15 i.e. "no preference")
* @NL80211_PMSR_FTM_REQ_ATTR_FTMS_PER_BURST: number of successful FTM frames
* requested per burst
* (u8, 0-31, optional with default 0 i.e. "no preference")
* @NL80211_PMSR_FTM_REQ_ATTR_NUM_FTMR_RETRIES: number of FTMR frame retries
* (u8, default 3)
* @NL80211_PMSR_FTM_REQ_ATTR_REQUEST_LCI: request LCI data (flag)
* @NL80211_PMSR_FTM_REQ_ATTR_REQUEST_CIVICLOC: request civic location data
* (flag)
* @NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED: request trigger based ranging
* measurement (flag).
* This attribute and %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED are
* mutually exclusive.
* if neither %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED nor
* %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set, EDCA based
* ranging will be used.
* @NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED: request non trigger based
* ranging measurement (flag)
* This attribute and %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED are
* mutually exclusive.
* if neither %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED nor
* %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set, EDCA based
* ranging will be used.
* @NL80211_PMSR_FTM_REQ_ATTR_LMR_FEEDBACK: negotiate for LMR feedback. Only
* valid if either %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED or
* %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set.
* @NL80211_PMSR_FTM_REQ_ATTR_BSS_COLOR: optional. The BSS color of the
* responder. Only valid if %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED
* or %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED is set.
*
* @NUM_NL80211_PMSR_FTM_REQ_ATTR: internal
* @NL80211_PMSR_FTM_REQ_ATTR_MAX: highest attribute number
*/
enum nl80211_peer_measurement_ftm_req {
__NL80211_PMSR_FTM_REQ_ATTR_INVALID,
NL80211_PMSR_FTM_REQ_ATTR_ASAP,
NL80211_PMSR_FTM_REQ_ATTR_PREAMBLE,
NL80211_PMSR_FTM_REQ_ATTR_NUM_BURSTS_EXP,
NL80211_PMSR_FTM_REQ_ATTR_BURST_PERIOD,
NL80211_PMSR_FTM_REQ_ATTR_BURST_DURATION,
NL80211_PMSR_FTM_REQ_ATTR_FTMS_PER_BURST,
NL80211_PMSR_FTM_REQ_ATTR_NUM_FTMR_RETRIES,
NL80211_PMSR_FTM_REQ_ATTR_REQUEST_LCI,
NL80211_PMSR_FTM_REQ_ATTR_REQUEST_CIVICLOC,
NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED,
NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED,
NL80211_PMSR_FTM_REQ_ATTR_LMR_FEEDBACK,
NL80211_PMSR_FTM_REQ_ATTR_BSS_COLOR,
/* keep last */
NUM_NL80211_PMSR_FTM_REQ_ATTR,
NL80211_PMSR_FTM_REQ_ATTR_MAX = NUM_NL80211_PMSR_FTM_REQ_ATTR - 1
};
/**
* enum nl80211_peer_measurement_ftm_failure_reasons - FTM failure reasons
* @NL80211_PMSR_FTM_FAILURE_UNSPECIFIED: unspecified failure, not used
* @NL80211_PMSR_FTM_FAILURE_NO_RESPONSE: no response from the FTM responder
* @NL80211_PMSR_FTM_FAILURE_REJECTED: FTM responder rejected measurement
* @NL80211_PMSR_FTM_FAILURE_WRONG_CHANNEL: we already know the peer is
* on a different channel, so can't measure (if we didn't know, we'd
* try and get no response)
* @NL80211_PMSR_FTM_FAILURE_PEER_NOT_CAPABLE: peer can't actually do FTM
* @NL80211_PMSR_FTM_FAILURE_INVALID_TIMESTAMP: invalid T1/T4 timestamps
* received
* @NL80211_PMSR_FTM_FAILURE_PEER_BUSY: peer reports busy, you may retry
* later (see %NL80211_PMSR_FTM_RESP_ATTR_BUSY_RETRY_TIME)
* @NL80211_PMSR_FTM_FAILURE_BAD_CHANGED_PARAMS: parameters were changed
* by the peer and are no longer supported
*/
enum nl80211_peer_measurement_ftm_failure_reasons {
NL80211_PMSR_FTM_FAILURE_UNSPECIFIED,
NL80211_PMSR_FTM_FAILURE_NO_RESPONSE,
NL80211_PMSR_FTM_FAILURE_REJECTED,
NL80211_PMSR_FTM_FAILURE_WRONG_CHANNEL,
NL80211_PMSR_FTM_FAILURE_PEER_NOT_CAPABLE,
NL80211_PMSR_FTM_FAILURE_INVALID_TIMESTAMP,
NL80211_PMSR_FTM_FAILURE_PEER_BUSY,
NL80211_PMSR_FTM_FAILURE_BAD_CHANGED_PARAMS,
};
/**
* enum nl80211_peer_measurement_ftm_resp - FTM response attributes
* @__NL80211_PMSR_FTM_RESP_ATTR_INVALID: invalid
*
* @NL80211_PMSR_FTM_RESP_ATTR_FAIL_REASON: FTM-specific failure reason
* (u32, optional)
* @NL80211_PMSR_FTM_RESP_ATTR_BURST_INDEX: optional, if bursts are reported
* as separate results then it will be the burst index 0...(N-1) and
* the top level will indicate partial results (u32)
* @NL80211_PMSR_FTM_RESP_ATTR_NUM_FTMR_ATTEMPTS: number of FTM Request frames
* transmitted (u32, optional)
* @NL80211_PMSR_FTM_RESP_ATTR_NUM_FTMR_SUCCESSES: number of FTM Request frames
* that were acknowleged (u32, optional)
* @NL80211_PMSR_FTM_RESP_ATTR_BUSY_RETRY_TIME: retry time received from the
* busy peer (u32, seconds)
* @NL80211_PMSR_FTM_RESP_ATTR_NUM_BURSTS_EXP: actual number of bursts exponent
* used by the responder (similar to request, u8)
* @NL80211_PMSR_FTM_RESP_ATTR_BURST_DURATION: actual burst duration used by
* the responder (similar to request, u8)
* @NL80211_PMSR_FTM_RESP_ATTR_FTMS_PER_BURST: actual FTMs per burst used
* by the responder (similar to request, u8)
* @NL80211_PMSR_FTM_RESP_ATTR_RSSI_AVG: average RSSI across all FTM action
* frames (optional, s32, 1/2 dBm)
* @NL80211_PMSR_FTM_RESP_ATTR_RSSI_SPREAD: RSSI spread across all FTM action
* frames (optional, s32, 1/2 dBm)
* @NL80211_PMSR_FTM_RESP_ATTR_TX_RATE: bitrate we used for the response to the
* FTM action frame (optional, nested, using &enum nl80211_rate_info
* attributes)
* @NL80211_PMSR_FTM_RESP_ATTR_RX_RATE: bitrate the responder used for the FTM
* action frame (optional, nested, using &enum nl80211_rate_info attrs)
* @NL80211_PMSR_FTM_RESP_ATTR_RTT_AVG: average RTT (s64, picoseconds, optional
* but one of RTT/DIST must be present)
* @NL80211_PMSR_FTM_RESP_ATTR_RTT_VARIANCE: RTT variance (u64, ps^2, note that
* standard deviation is the square root of variance, optional)
* @NL80211_PMSR_FTM_RESP_ATTR_RTT_SPREAD: RTT spread (u64, picoseconds,
* optional)
* @NL80211_PMSR_FTM_RESP_ATTR_DIST_AVG: average distance (s64, mm, optional
* but one of RTT/DIST must be present)
* @NL80211_PMSR_FTM_RESP_ATTR_DIST_VARIANCE: distance variance (u64, mm^2, note
* that standard deviation is the square root of variance, optional)
* @NL80211_PMSR_FTM_RESP_ATTR_DIST_SPREAD: distance spread (u64, mm, optional)
* @NL80211_PMSR_FTM_RESP_ATTR_LCI: LCI data from peer (binary, optional);
* this is the contents of the Measurement Report Element (802.11-2016
* 9.4.2.22.1) starting with the Measurement Token, with Measurement
* Type 8.
* @NL80211_PMSR_FTM_RESP_ATTR_CIVICLOC: civic location data from peer
* (binary, optional);
* this is the contents of the Measurement Report Element (802.11-2016
* 9.4.2.22.1) starting with the Measurement Token, with Measurement
* Type 11.
* @NL80211_PMSR_FTM_RESP_ATTR_PAD: ignore, for u64/s64 padding only
*
* @NUM_NL80211_PMSR_FTM_RESP_ATTR: internal
* @NL80211_PMSR_FTM_RESP_ATTR_MAX: highest attribute number
*/
enum nl80211_peer_measurement_ftm_resp {
__NL80211_PMSR_FTM_RESP_ATTR_INVALID,
NL80211_PMSR_FTM_RESP_ATTR_FAIL_REASON,
NL80211_PMSR_FTM_RESP_ATTR_BURST_INDEX,
NL80211_PMSR_FTM_RESP_ATTR_NUM_FTMR_ATTEMPTS,
NL80211_PMSR_FTM_RESP_ATTR_NUM_FTMR_SUCCESSES,
NL80211_PMSR_FTM_RESP_ATTR_BUSY_RETRY_TIME,
NL80211_PMSR_FTM_RESP_ATTR_NUM_BURSTS_EXP,
NL80211_PMSR_FTM_RESP_ATTR_BURST_DURATION,
NL80211_PMSR_FTM_RESP_ATTR_FTMS_PER_BURST,
NL80211_PMSR_FTM_RESP_ATTR_RSSI_AVG,
NL80211_PMSR_FTM_RESP_ATTR_RSSI_SPREAD,
NL80211_PMSR_FTM_RESP_ATTR_TX_RATE,
NL80211_PMSR_FTM_RESP_ATTR_RX_RATE,
NL80211_PMSR_FTM_RESP_ATTR_RTT_AVG,
NL80211_PMSR_FTM_RESP_ATTR_RTT_VARIANCE,
NL80211_PMSR_FTM_RESP_ATTR_RTT_SPREAD,
NL80211_PMSR_FTM_RESP_ATTR_DIST_AVG,
NL80211_PMSR_FTM_RESP_ATTR_DIST_VARIANCE,
NL80211_PMSR_FTM_RESP_ATTR_DIST_SPREAD,
NL80211_PMSR_FTM_RESP_ATTR_LCI,
NL80211_PMSR_FTM_RESP_ATTR_CIVICLOC,
NL80211_PMSR_FTM_RESP_ATTR_PAD,
/* keep last */
NUM_NL80211_PMSR_FTM_RESP_ATTR,
NL80211_PMSR_FTM_RESP_ATTR_MAX = NUM_NL80211_PMSR_FTM_RESP_ATTR - 1
};
/**
* enum nl80211_obss_pd_attributes - OBSS packet detection attributes
* @__NL80211_HE_OBSS_PD_ATTR_INVALID: Invalid
*
* @NL80211_HE_OBSS_PD_ATTR_MIN_OFFSET: the OBSS PD minimum tx power offset.
* @NL80211_HE_OBSS_PD_ATTR_MAX_OFFSET: the OBSS PD maximum tx power offset.
* @NL80211_HE_OBSS_PD_ATTR_NON_SRG_MAX_OFFSET: the non-SRG OBSS PD maximum
* tx power offset.
* @NL80211_HE_OBSS_PD_ATTR_BSS_COLOR_BITMAP: bitmap that indicates the BSS color
* values used by members of the SRG.
* @NL80211_HE_OBSS_PD_ATTR_PARTIAL_BSSID_BITMAP: bitmap that indicates the partial
* BSSID values used by members of the SRG.
* @NL80211_HE_OBSS_PD_ATTR_SR_CTRL: The SR Control field of SRP element.
*
* @__NL80211_HE_OBSS_PD_ATTR_LAST: Internal
* @NL80211_HE_OBSS_PD_ATTR_MAX: highest OBSS PD attribute.
*/
enum nl80211_obss_pd_attributes {
__NL80211_HE_OBSS_PD_ATTR_INVALID,
NL80211_HE_OBSS_PD_ATTR_MIN_OFFSET,
NL80211_HE_OBSS_PD_ATTR_MAX_OFFSET,
NL80211_HE_OBSS_PD_ATTR_NON_SRG_MAX_OFFSET,
NL80211_HE_OBSS_PD_ATTR_BSS_COLOR_BITMAP,
NL80211_HE_OBSS_PD_ATTR_PARTIAL_BSSID_BITMAP,
NL80211_HE_OBSS_PD_ATTR_SR_CTRL,
/* keep last */
__NL80211_HE_OBSS_PD_ATTR_LAST,
NL80211_HE_OBSS_PD_ATTR_MAX = __NL80211_HE_OBSS_PD_ATTR_LAST - 1,
};
/**
* enum nl80211_bss_color_attributes - BSS Color attributes
* @__NL80211_HE_BSS_COLOR_ATTR_INVALID: Invalid
*
* @NL80211_HE_BSS_COLOR_ATTR_COLOR: the current BSS Color.
* @NL80211_HE_BSS_COLOR_ATTR_DISABLED: is BSS coloring disabled.
* @NL80211_HE_BSS_COLOR_ATTR_PARTIAL: the AID equation to be used..
*
* @__NL80211_HE_BSS_COLOR_ATTR_LAST: Internal
* @NL80211_HE_BSS_COLOR_ATTR_MAX: highest BSS Color attribute.
*/
enum nl80211_bss_color_attributes {
__NL80211_HE_BSS_COLOR_ATTR_INVALID,
NL80211_HE_BSS_COLOR_ATTR_COLOR,
NL80211_HE_BSS_COLOR_ATTR_DISABLED,
NL80211_HE_BSS_COLOR_ATTR_PARTIAL,
/* keep last */
__NL80211_HE_BSS_COLOR_ATTR_LAST,
NL80211_HE_BSS_COLOR_ATTR_MAX = __NL80211_HE_BSS_COLOR_ATTR_LAST - 1,
};
/**
* enum nl80211_iftype_akm_attributes - interface type AKM attributes
* @__NL80211_IFTYPE_AKM_ATTR_INVALID: Invalid
*
* @NL80211_IFTYPE_AKM_ATTR_IFTYPES: nested attribute containing a flag
* attribute for each interface type that supports AKM suites specified in
* %NL80211_IFTYPE_AKM_ATTR_SUITES
* @NL80211_IFTYPE_AKM_ATTR_SUITES: an array of u32. Used to indicate supported
* AKM suites for the specified interface types.
*
* @__NL80211_IFTYPE_AKM_ATTR_LAST: Internal
* @NL80211_IFTYPE_AKM_ATTR_MAX: highest interface type AKM attribute.
*/
enum nl80211_iftype_akm_attributes {
__NL80211_IFTYPE_AKM_ATTR_INVALID,
NL80211_IFTYPE_AKM_ATTR_IFTYPES,
NL80211_IFTYPE_AKM_ATTR_SUITES,
/* keep last */
__NL80211_IFTYPE_AKM_ATTR_LAST,
NL80211_IFTYPE_AKM_ATTR_MAX = __NL80211_IFTYPE_AKM_ATTR_LAST - 1,
};
/**
* enum nl80211_fils_discovery_attributes - FILS discovery configuration
* from IEEE Std 802.11ai-2016, Annex C.3 MIB detail.
*
* @__NL80211_FILS_DISCOVERY_ATTR_INVALID: Invalid
*
* @NL80211_FILS_DISCOVERY_ATTR_INT_MIN: Minimum packet interval (u32, TU).
* Allowed range: 0..10000 (TU = Time Unit)
* @NL80211_FILS_DISCOVERY_ATTR_INT_MAX: Maximum packet interval (u32, TU).
* Allowed range: 0..10000 (TU = Time Unit)
* @NL80211_FILS_DISCOVERY_ATTR_TMPL: Template data for FILS discovery action
* frame including the headers.
*
* @__NL80211_FILS_DISCOVERY_ATTR_LAST: Internal
* @NL80211_FILS_DISCOVERY_ATTR_MAX: highest attribute
*/
enum nl80211_fils_discovery_attributes {
__NL80211_FILS_DISCOVERY_ATTR_INVALID,
NL80211_FILS_DISCOVERY_ATTR_INT_MIN,
NL80211_FILS_DISCOVERY_ATTR_INT_MAX,
NL80211_FILS_DISCOVERY_ATTR_TMPL,
/* keep last */
__NL80211_FILS_DISCOVERY_ATTR_LAST,
NL80211_FILS_DISCOVERY_ATTR_MAX = __NL80211_FILS_DISCOVERY_ATTR_LAST - 1
};
/*
* FILS discovery template minimum length with action frame headers and
* mandatory fields.
*/
#define NL80211_FILS_DISCOVERY_TMPL_MIN_LEN 42
/**
* enum nl80211_unsol_bcast_probe_resp_attributes - Unsolicited broadcast probe
* response configuration. Applicable only in 6GHz.
*
* @__NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_INVALID: Invalid
*
* @NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_INT: Maximum packet interval (u32, TU).
* Allowed range: 0..20 (TU = Time Unit). IEEE P802.11ax/D6.0
* 26.17.2.3.2 (AP behavior for fast passive scanning).
* @NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_TMPL: Unsolicited broadcast probe response
* frame template (binary).
*
* @__NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_LAST: Internal
* @NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_MAX: highest attribute
*/
enum nl80211_unsol_bcast_probe_resp_attributes {
__NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_INVALID,
NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_INT,
NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_TMPL,
/* keep last */
__NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_LAST,
NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_MAX =
__NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_LAST - 1
};
/**
* enum nl80211_sae_pwe_mechanism - The mechanism(s) allowed for SAE PWE
* derivation. Applicable only when WPA3-Personal SAE authentication is
* used.
*
* @NL80211_SAE_PWE_UNSPECIFIED: not specified, used internally to indicate that
* attribute is not present from userspace.
* @NL80211_SAE_PWE_HUNT_AND_PECK: hunting-and-pecking loop only
* @NL80211_SAE_PWE_HASH_TO_ELEMENT: hash-to-element only
* @NL80211_SAE_PWE_BOTH: both hunting-and-pecking loop and hash-to-element
* can be used.
*/
enum nl80211_sae_pwe_mechanism {
NL80211_SAE_PWE_UNSPECIFIED,
NL80211_SAE_PWE_HUNT_AND_PECK,
NL80211_SAE_PWE_HASH_TO_ELEMENT,
NL80211_SAE_PWE_BOTH,
};
/**
* enum nl80211_sar_type - type of SAR specs
*
* @NL80211_SAR_TYPE_POWER: power limitation specified in 0.25dBm unit
*
*/
enum nl80211_sar_type {
NL80211_SAR_TYPE_POWER,
/* add new type here */
/* Keep last */
NUM_NL80211_SAR_TYPE,
};
/**
* enum nl80211_sar_attrs - Attributes for SAR spec
*
* @NL80211_SAR_ATTR_TYPE: the SAR type as defined in &enum nl80211_sar_type.
*
* @NL80211_SAR_ATTR_SPECS: Nested array of SAR power
* limit specifications. Each specification contains a set
* of %nl80211_sar_specs_attrs.
*
* For SET operation, it contains array of %NL80211_SAR_ATTR_SPECS_POWER
* and %NL80211_SAR_ATTR_SPECS_RANGE_INDEX.
*
* For sar_capa dump, it contains array of
* %NL80211_SAR_ATTR_SPECS_START_FREQ
* and %NL80211_SAR_ATTR_SPECS_END_FREQ.
*
* @__NL80211_SAR_ATTR_LAST: Internal
* @NL80211_SAR_ATTR_MAX: highest sar attribute
*
* These attributes are used with %NL80211_CMD_SET_SAR_SPEC
*/
enum nl80211_sar_attrs {
__NL80211_SAR_ATTR_INVALID,
NL80211_SAR_ATTR_TYPE,
NL80211_SAR_ATTR_SPECS,
__NL80211_SAR_ATTR_LAST,
NL80211_SAR_ATTR_MAX = __NL80211_SAR_ATTR_LAST - 1,
};
/**
* enum nl80211_sar_specs_attrs - Attributes for SAR power limit specs
*
* @NL80211_SAR_ATTR_SPECS_POWER: Required (s32)value to specify the actual
* power limit value in units of 0.25 dBm if type is
* NL80211_SAR_TYPE_POWER. (i.e., a value of 44 represents 11 dBm).
* 0 means userspace doesn't have SAR limitation on this associated range.
*
* @NL80211_SAR_ATTR_SPECS_RANGE_INDEX: Required (u32) value to specify the
* index of exported freq range table and the associated power limitation
* is applied to this range.
*
* Userspace isn't required to set all the ranges advertised by WLAN driver,
* and userspace can skip some certain ranges. These skipped ranges don't
* have SAR limitations, and they are same as setting the
* %NL80211_SAR_ATTR_SPECS_POWER to any unreasonable high value because any
* value higher than regulatory allowed value just means SAR power
* limitation is removed, but it's required to set at least one range.
* It's not allowed to set duplicated range in one SET operation.
*
* Every SET operation overwrites previous SET operation.
*
* @NL80211_SAR_ATTR_SPECS_START_FREQ: Required (u32) value to specify the start
* frequency of this range edge when registering SAR capability to wiphy.
* It's not a channel center frequency. The unit is kHz.
*
* @NL80211_SAR_ATTR_SPECS_END_FREQ: Required (u32) value to specify the end
* frequency of this range edge when registering SAR capability to wiphy.
* It's not a channel center frequency. The unit is kHz.
*
* @__NL80211_SAR_ATTR_SPECS_LAST: Internal
* @NL80211_SAR_ATTR_SPECS_MAX: highest sar specs attribute
*/
enum nl80211_sar_specs_attrs {
__NL80211_SAR_ATTR_SPECS_INVALID,
NL80211_SAR_ATTR_SPECS_POWER,
NL80211_SAR_ATTR_SPECS_RANGE_INDEX,
NL80211_SAR_ATTR_SPECS_START_FREQ,
NL80211_SAR_ATTR_SPECS_END_FREQ,
__NL80211_SAR_ATTR_SPECS_LAST,
NL80211_SAR_ATTR_SPECS_MAX = __NL80211_SAR_ATTR_SPECS_LAST - 1,
};
/**
* enum nl80211_mbssid_config_attributes - multiple BSSID (MBSSID) and enhanced
* multi-BSSID advertisements (EMA) in AP mode.
* Kernel uses some of these attributes to advertise driver's support for
* MBSSID and EMA.
* Remaining attributes should be used by the userspace to configure the
* features.
*
* @__NL80211_MBSSID_CONFIG_ATTR_INVALID: Invalid
*
* @NL80211_MBSSID_CONFIG_ATTR_MAX_INTERFACES: Used by the kernel to advertise
* the maximum number of MBSSID interfaces supported by the driver.
* Driver should indicate MBSSID support by setting
* wiphy->mbssid_max_interfaces to a value more than or equal to 2.
*
* @NL80211_MBSSID_CONFIG_ATTR_MAX_EMA_PROFILE_PERIODICITY: Used by the kernel
* to advertise the maximum profile periodicity supported by the driver
* if EMA is enabled. Driver should indicate EMA support to the userspace
* by setting wiphy->ema_max_profile_periodicity to
* a non-zero value.
*
* @NL80211_MBSSID_CONFIG_ATTR_INDEX: Mandatory parameter to pass the index of
* this BSS (u8) in the multiple BSSID set.
* Value must be set to 0 for the transmitting interface and non-zero for
* all non-transmitting interfaces. The userspace will be responsible
* for using unique indices for the interfaces.
* Range: 0 to wiphy->mbssid_max_interfaces-1.
*
* @NL80211_MBSSID_CONFIG_ATTR_TX_IFINDEX: Mandatory parameter for
* a non-transmitted profile which provides the interface index (u32) of
* the transmitted profile. The value must match one of the interface
* indices advertised by the kernel. Optional if the interface being set up
* is the transmitting one, however, if provided then the value must match
* the interface index of the same.
*
* @NL80211_MBSSID_CONFIG_ATTR_EMA: Flag used to enable EMA AP feature.
* Setting this flag is permitted only if the driver advertises EMA support
* by setting wiphy->ema_max_profile_periodicity to non-zero.
*
* @__NL80211_MBSSID_CONFIG_ATTR_LAST: Internal
* @NL80211_MBSSID_CONFIG_ATTR_MAX: highest attribute
*/
enum nl80211_mbssid_config_attributes {
__NL80211_MBSSID_CONFIG_ATTR_INVALID,
NL80211_MBSSID_CONFIG_ATTR_MAX_INTERFACES,
NL80211_MBSSID_CONFIG_ATTR_MAX_EMA_PROFILE_PERIODICITY,
NL80211_MBSSID_CONFIG_ATTR_INDEX,
NL80211_MBSSID_CONFIG_ATTR_TX_IFINDEX,
NL80211_MBSSID_CONFIG_ATTR_EMA,
/* keep last */
__NL80211_MBSSID_CONFIG_ATTR_LAST,
NL80211_MBSSID_CONFIG_ATTR_MAX = __NL80211_MBSSID_CONFIG_ATTR_LAST - 1,
};
/**
* enum nl80211_ap_settings_flags - AP settings flags
*
* @NL80211_AP_SETTINGS_EXTERNAL_AUTH_SUPPORT: AP supports external
* authentication.
* @NL80211_AP_SETTINGS_SA_QUERY_OFFLOAD_SUPPORT: Userspace supports SA Query
* procedures offload to driver. If driver advertises
* %NL80211_AP_SME_SA_QUERY_OFFLOAD in AP SME features, userspace shall
* ignore SA Query procedures and validations when this flag is set by
* userspace.
*/
enum nl80211_ap_settings_flags {
NL80211_AP_SETTINGS_EXTERNAL_AUTH_SUPPORT = 1 << 0,
NL80211_AP_SETTINGS_SA_QUERY_OFFLOAD_SUPPORT = 1 << 1,
};
#endif /* __LINUX_NL80211_H */
|