Viewing file:  ipmi_msgdefs.h (3.35 KB) -rw-r--r--
Select action/file-type:
 (+) |  (+) |  (+) | Code (+) | Session (+) |  (+) | SDB (+) |  (+) |  (+) |  (+) |  (+) |  (+) |
/* SPDX-License-Identifier: GPL-2.0+ WITH Linux-syscall-note */
/*
* ipmi_smi.h
*
* MontaVista IPMI system management interface
*
* Author: MontaVista Software, Inc.
* Corey Minyard <minyard@mvista.com>
* source@mvista.com
*
* Copyright 2002 MontaVista Software Inc.
*
*/
#ifndef __LINUX_IPMI_MSGDEFS_H
#define __LINUX_IPMI_MSGDEFS_H
/* Various definitions for IPMI messages used by almost everything in
the IPMI stack. */
/* NetFNs and commands used inside the IPMI stack. */
#define IPMI_NETFN_SENSOR_EVENT_REQUEST 0x04
#define IPMI_NETFN_SENSOR_EVENT_RESPONSE 0x05
#define IPMI_GET_EVENT_RECEIVER_CMD 0x01
#define IPMI_NETFN_APP_REQUEST 0x06
#define IPMI_NETFN_APP_RESPONSE 0x07
#define IPMI_GET_DEVICE_ID_CMD 0x01
#define IPMI_COLD_RESET_CMD 0x02
#define IPMI_WARM_RESET_CMD 0x03
#define IPMI_CLEAR_MSG_FLAGS_CMD 0x30
#define IPMI_GET_DEVICE_GUID_CMD 0x08
#define IPMI_GET_MSG_FLAGS_CMD 0x31
#define IPMI_SEND_MSG_CMD 0x34
#define IPMI_GET_MSG_CMD 0x33
#define IPMI_SET_BMC_GLOBAL_ENABLES_CMD 0x2e
#define IPMI_GET_BMC_GLOBAL_ENABLES_CMD 0x2f
#define IPMI_READ_EVENT_MSG_BUFFER_CMD 0x35
#define IPMI_GET_CHANNEL_INFO_CMD 0x42
/* Bit for BMC global enables. */
#define IPMI_BMC_RCV_MSG_INTR 0x01
#define IPMI_BMC_EVT_MSG_INTR 0x02
#define IPMI_BMC_EVT_MSG_BUFF 0x04
#define IPMI_BMC_SYS_LOG 0x08
#define IPMI_NETFN_STORAGE_REQUEST 0x0a
#define IPMI_NETFN_STORAGE_RESPONSE 0x0b
#define IPMI_ADD_SEL_ENTRY_CMD 0x44
#define IPMI_NETFN_FIRMWARE_REQUEST 0x08
#define IPMI_NETFN_FIRMWARE_RESPONSE 0x09
/* The default slave address */
#define IPMI_BMC_SLAVE_ADDR 0x20
/* The BT interface on high-end HP systems supports up to 255 bytes in
* one transfer. Its "virtual" BMC supports some commands that are longer
* than 128 bytes. Use the full 256, plus NetFn/LUN, Cmd, cCode, plus
* some overhead; it's not worth the effort to dynamically size this based
* on the results of the "Get BT Capabilities" command. */
#define IPMI_MAX_MSG_LENGTH 272 /* multiple of 16 */
#define IPMI_CC_NO_ERROR 0x00
#define IPMI_NODE_BUSY_ERR 0xc0
#define IPMI_INVALID_COMMAND_ERR 0xc1
#define IPMI_TIMEOUT_ERR 0xc3
#define IPMI_ERR_MSG_TRUNCATED 0xc6
#define IPMI_REQ_LEN_INVALID_ERR 0xc7
#define IPMI_REQ_LEN_EXCEEDED_ERR 0xc8
#define IPMI_DEVICE_IN_FW_UPDATE_ERR 0xd1
#define IPMI_DEVICE_IN_INIT_ERR 0xd2
#define IPMI_NOT_IN_MY_STATE_ERR 0xd5 /* IPMI 2.0 */
#define IPMI_LOST_ARBITRATION_ERR 0x81
#define IPMI_BUS_ERR 0x82
#define IPMI_NAK_ON_WRITE_ERR 0x83
#define IPMI_ERR_UNSPECIFIED 0xff
#define IPMI_CHANNEL_PROTOCOL_IPMB 1
#define IPMI_CHANNEL_PROTOCOL_ICMB 2
#define IPMI_CHANNEL_PROTOCOL_SMBUS 4
#define IPMI_CHANNEL_PROTOCOL_KCS 5
#define IPMI_CHANNEL_PROTOCOL_SMIC 6
#define IPMI_CHANNEL_PROTOCOL_BT10 7
#define IPMI_CHANNEL_PROTOCOL_BT15 8
#define IPMI_CHANNEL_PROTOCOL_TMODE 9
#define IPMI_CHANNEL_MEDIUM_IPMB 1
#define IPMI_CHANNEL_MEDIUM_ICMB10 2
#define IPMI_CHANNEL_MEDIUM_ICMB09 3
#define IPMI_CHANNEL_MEDIUM_8023LAN 4
#define IPMI_CHANNEL_MEDIUM_ASYNC 5
#define IPMI_CHANNEL_MEDIUM_OTHER_LAN 6
#define IPMI_CHANNEL_MEDIUM_PCI_SMBUS 7
#define IPMI_CHANNEL_MEDIUM_SMBUS1 8
#define IPMI_CHANNEL_MEDIUM_SMBUS2 9
#define IPMI_CHANNEL_MEDIUM_USB1 10
#define IPMI_CHANNEL_MEDIUM_USB2 11
#define IPMI_CHANNEL_MEDIUM_SYSINTF 12
#define IPMI_CHANNEL_MEDIUM_OEM_MIN 0x60
#define IPMI_CHANNEL_MEDIUM_OEM_MAX 0x7f
#endif /* __LINUX_IPMI_MSGDEFS_H */
|